43.060.40 标准查询与下载
共找到 1309 条与 相关的标准，共 88 页
This document specifies general information regarding the hose component of liquefied petroleum gas fuel, intended for use on the types of motor vehicles as defined in ISO 3833. It provides general design principles and specifies requirements for instructions and marking. It also specifies test requirements for the hose. This document is applicable to vehicles (mono-fuel, bi-fuel or dual-fuel applications) using gaseous fuels in accordance with ISO 9162. It is not applicable to the following: a) fuel containers; b) stationary gas engines; c) container mounting hardware; d) electronic fuel management; e) refuelling receptacles. Fully metal bendable hoses are excluded from this document. NOTE 1 It is recognized that miscellaneous components not specifically addressed herein can be examined for compliance with the criteria of any applicable part of ISO 20766, including testing to the appropriate functional tests. NOTE 2 All references to pressure in this document are considered gauge pressures unless otherwise specified. NOTE 3 This document applies to devices which have a service pressure in the range of 110 kPa (Butane rich at 20 °C) and 840 kPa (Propane at 20 °C), hereinafter referred to in this document. Other service pressures can be accommodated by adjusting the pressure by the appropriate factor (ratio).
Road vehicles — Liquefied petroleum gas (LPG) fuel systems components — Part 18: Hose
- ICS
- 43.060.40
- CCS
- 发布
- 2024-01-31
- 实施
This document specifies general requirements and definitions of liquefied petroleum gas fuel components, intended for use on the types of motor vehicles as defined in ISO 3833. It also provides general design principles, and specifies requirements for instructions and marking. This document is applicable to vehicles (mono-fuel, bi-fuel or dual-fuel applications) using gaseous fuels in accordance with ISO 9162. It is not applicable to the following: a) fuel containers; b) stationary gas engines; c) container mounting hardware; d) electronic fuel management; and e) refuelling receptacles. NOTE 1 It is recognized that miscellaneous components not specifically addressed herein can be examined for compliance with the criteria of any applicable part of ISO 20766, including testing to the appropriate functional tests. NOTE 2 All references to pressure in this document are considered gauge pressures unless otherwise specified. NOTE 3 This document applies to devices which have a service pressure in the range of 110 kPa (Butane rich at 20 °C) and 840 kPa (Propane at 20 °C), hereinafter referred to in this document. Other service pressures can be accommodated by adjusting the pressure by the appropriate factor (ratio).
Road vehicles — Liquefied petroleum gas (LPG) fuel systems components — Part 3: 80% stop valve
- ICS
- 43.060.40
- CCS
- 发布
- 2024-01-31
- 实施
This document specifies general requirements and definitions of liquefied petroleum gas fuel system components, intended for use on the types of motor vehicles as defined in ISO 3833. It also provides general design principles, and specifies requirements for instructions and marking. This document is applicable to vehicles (mono-fuel, bi-fuel or dual-fuel applications) using gaseous fuels in accordance with ISO 9162. It is not applicable to the following: a) fuel containers; b) stationary gas engines; c) container mounting hardware; d) electronic fuel management; and e) refuelling receptacles. NOTE 1 It is recognized that miscellaneous components not specifically addressed herein can be examined for compliance with the criteria of any applicable part of ISO 20766, including testing to the appropriate functional tests. NOTE 2 All references to pressure in this document are considered gauge pressures unless otherwise specified. NOTE 3 This document applies to devices which have a service pressure in the range of 110 kPa (Butane rich at 20 °C) and 840 kPa (Propane rich at 20 °C), hereinafter referred to in this document. Other service pressures can be accommodated by adjusting the pressure by the appropriate factor (ratio).
Road vehicles — Liquefied petroleum gas (LPG) fuel systems components — Part 1: General requirements and definitions
- ICS
- 43.060.40
- CCS
- 发布
- 2024-01-31
- 实施
This document specifies general requirements for the vaporizer/pressure regulator, a component of liquefied petroleum gas fuel, intended for use on the types of motor vehicles as defined in ISO 3833. It also provides general design principles and specifies requirements for instructions and marking. This document is applicable to vehicles (mono-fuel, bi-fuel or dual-fuel applications) using gaseous fuels in accordance with ISO 9162. It is not applicable to the following: a) fuel containers; b) stationary gas engines; c) container mounting hardware; d) electronic fuel management; e) refuelling receptacles. It is recognized that miscellaneous components not specifically addressed herein can be examined for compliance with the criteria of any applicable part of the ISO 20766 series, including testing to the appropriate functional tests. All references to pressure in this document are considered gauge pressures unless otherwise specified. This document applies to devices which have a service pressure in the range of 110 kPa (butane rich at 20 °C) and 840 kPa (propane at 20 °C), hereinafter referred to in this document. Other service pressures can be accommodated by adjusting the pressure by the appropriate factor (ratio).
Road vehicles — Liquefied petroleum gas (LPG) fuel system components — Part 14: Vaporizer/pressure regulator
- ICS
- 43.060.40
- CCS
- 发布
- 2024-01-31
- 实施
This document specifies general requirements and definitions of liquefied petroleum gas fuel components, intended for use on the types of motor vehicles as defined in ISO 3833. It also provides general design principles, and specifies requirements for instructions and marking. This document is applicable to vehicles (mono-fuel, bi-fuel or dual-fuel applications) using gaseous fuels in accordance with ISO 9162. It is not applicable to the following: a) fuel containers; b) stationary gas engines; c) container mounting hardware; d) electronic fuel management; and e) refuelling receptacles. NOTE 1 It is recognized that miscellaneous components not specifically addressed herein can be examined for compliance with the criteria of any applicable part of ISO 20766, including testing to the appropriate functional tests. NOTE 2 All references to pressure in this document are considered gauge pressures unless otherwise specified. NOTE 3 This document applies to devices which have a service pressure in the range of 110 kPa (Butane rich at 20 °C) and 840 kPa (Propane at 20 °C), hereinafter referred to in this document. Other service pressures can be accommodated by adjusting the pressure by the appropriate factor (ratio).
Road vehicles — Liquefied petroleum gas (LPG) fuel systems components — Part 6: Pressure relief valves (PRV)
- ICS
- 43.060.40
- CCS
- 发布
- 2024-01-31
- 实施
BS ISO 20766-23 Road vehicles — Liquefied petroleum gas (LPG) fuel system components - Part 22: Power supply bushing (fuel pump/actuators/fuel level sensor)
- ICS
- 43.060.40
- CCS
- 发布
- 2024-01-26
- 实施
- 2024-01-26
BS ISO 13948-2 Diesel engines - Fuel injection pumps and fuel injector low-pressure connections - Part 2: Non-threaded (push-on) connections
- ICS
- 43.060.40
- CCS
- 发布
- 2024-01-16
- 实施
- 2024-01-16
本文件规定了汽车流体管路系统快换接头的技术要求、试验方法、检验规则、标志、包装、运输及贮存。
Quick Connectors of Auto fluid pipe system
- ICS
- 43.060.40
- CCS
- C3670
- 发布
- 2023-11-30
- 实施
- 2023-12-01
本文件规定了甲醇燃料储存箱（罐）的技术要求、试验方法、检验规则、标志、包装、运输及贮存等。 本文件适用于甲醇发动机、甲醇发电机使用的甲醇燃料储存箱（罐）（以下简称燃料箱）。甲醇采暖炉、甲醇灶具、甲醇锅炉等甲醇燃料热力燃烧应用装备推荐参照本文件。
Technical conditions and test methods for methanol fuel storage boxes (tanks)
- ICS
- 43.060.40
- CCS
- G544
- 发布
- 2023-11-24
- 实施
- 2023-11-30
Road vehicles－Fuel filters for diesel engines－Test methods
- ICS
- 43.060.40
- CCS
- 发布
- 2023-11-03
- 实施
Diesel engines — Fuel injection pumps — High-pressure pipes for testing
- ICS
- 43.060.40
- CCS
- 发布
- 2023-11-03
- 实施
Gaseous hydrogen — Fuelling stations — Part 7: Rubber O-rings
- ICS
- 43.060.40
- CCS
- 发布
- 2023-10
- 实施
Gaseous hydrogen — Fuelling stations — Part 5: Dispenser hoses and hose assemblies
- ICS
- 43.060.40
- CCS
- 发布
- 2023-10
- 实施
Road vehicles. Compressed natural gas (CNG) fuel system components - Gas temperature sensor
- ICS
- 43.060.40
- CCS
- 发布
- 2023-09-30
- 实施
- 2023-09-30
Road vehicles — Compressed natural gas (CNG) fuel system components — Part 23: Gas temperature sensor
- ICS
- 43.060.40
- CCS
- 发布
- 2023-08-31
- 实施
Road vehicles. Liquefied petroleum gas (LPG) fuel system components - Fuel selection system and electrical installations
- ICS
- 43.060.40
- CCS
- 发布
- 2023-08-31
- 实施
- 2023-08-31
Road vehicles. Liquefied natural gas (LNG) fuel system components - Flexible fuel or vent lines
- ICS
- 43.060.40
- CCS
- 发布
- 2023-08-31
- 实施
- 2023-08-31
This document specifies tests and requirements for the flexible fuel lines, a liquefied natural gas fuel system component intended for use on the types of motor vehicles defined in ISO 3833. This document is not applicable to the following: a) fuel containers; b) stationary gas engines; c) container mounting hardware; d) electronic fuel management; e) refuelling receptacles. NOTE 1 It is recognized that miscellaneous components not specifically covered herein can be examined to meet the criteria of this document and tested according to the appropriate functional tests. NOTE 2 All references to pressure in this document are considered gauge pressures unless otherwise specified. NOTE 3 This document is based upon a working pressure for natural gas as a fuel of 1,6 MPa (16 bar). (1 bar = 0,1 MPa = 105 Pa; 1 MPa = 1 N/mm2.) Other working pressures can be accommodated by adjusting the pressure by the appropriate factor (ratio). For example, a 2 MPa (20 bar) working pressure system will require pressures to be multiplied by 1,25.
Road vehicles — Liquefied natural gas (LNG) fuel system components — Part 20: Flexible fuel or vent lines
- ICS
- 43.060.40
- CCS
- 发布
- 2023-08-28
- 实施
This document specifies general requirements and definitions of liquefied petroleum gas fuel components (fuel selection system and electrical installations, intended for use on the types of motor vehicles as defined in ISO 3833). It also provides general design principles, and specifies requirements for instructions and marking. This document is applicable to vehicles (mono-fuel, bi-fuel or dual-fuel applications) using gaseous fuels in accordance with ISO 9162. It is not applicable to the following: a) fuel containers; b) stationary gas engines; c) container mounting hardware; d) refuelling receptacles. It is recognized that miscellaneous components not specifically addressed herein can be examined for compliance with the criteria of any applicable part of the ISO 20766 series, including testing to the appropriate functional tests. All references to pressure in this document are considered gauge pressures unless otherwise specified. This document applies to devices which have a service pressure in the range of 110 kPa (butane rich at 20 °C) and 840 kPa (propane rich at 20 °C), hereinafter referred to in this document. Other service pressures can be accommodated by adjusting the pressure by the appropriate factor (ratio).
Road vehicles — Liquefied petroleum gas (LPG) fuel system components — Part 5: Fuel selection system and electrical installations
- ICS
- 43.060.40
- CCS
- 发布
- 2023-08-28
- 实施
Gaseous hydrogen — Fuelling stations — Part 7: Rubber O-rings
- ICS
- 43.060.40
- CCS
- 发布
- 2023-07
- 实施
