43.060.50 标准查询与下载

BS AU 264:1995 道路车辆.带有圆锥形底座的M18x1.5火花塞及其汽缸盖外壳

This International Standard specifies the main charac-teristics of M18 × 1,5 spark-plugs with conical seating and their cylinder head housing, for use with spark-ignition engines.

Road vehicles - M18 X 1,5 spark-plugs with conical seating and their cylinder head housing

BS AU 262-1:1995 道路车辆.带有圆锥形底座的护套型热线点火塞及其汽缸盖外壳.M14x1.25热线点火塞

This part of ISO 6550 specifies the main character-istics of M14 × 1,25 sheath-type glow-plugs with conical seating and their cylinder head housing, for use with diesel (compression-ignition) engines. Type M14 should not be used for new applications.

Road vehicles - Sheath-type glow-plugs with conical seating and their cylinder head housing - M14 x 1, 25 glow-plugs

BS AU 262-2:1995 道路车辆.带有圆锥形底座的护套型热线点火塞及其汽缸盖外壳.M12x1.25热线点火塞

This part of ISO 6550 specifies the main character-istics of M12 × 1,25 sheath-type glow-plugs with conical seating and their cylinder head housing, for use with diesel (compression-ignition) engines.

Road vehicles - Sheath-type glow-plugs with conical seating and their cylinder head housing - M12 x 1.25 glow-plugs

BS AU 263:1995 道路车辆.带有圆锥形底座的M14x1.25压实火花塞及其汽缸盖外壳

This International Standard specifies the main charac-teristics of M14 × 1,25 compact spark-plugs with conical seating and their cylinder head housing, for use with spark-ignition engines.

Road vehicles - M14 X 1,25 compact spark-plugs with conical seating and their cylinder head housing

BS AU 265-2:1995 公路车辆 点火系统 电气性能和功能测试方法

This part of ISO 6518 specifies the methods and test conditions for testing battery-supplied ignition sys-tems for spark-ignited internal combustion engines. Because of the difficulties in producing repeatable measurements with atmospheric spark gaps and dif-ferent observers, two methods of obtaining the re-sults necessary for calculating the system output energy are given. Method A —using spark gaps for the energy measurement (test arrangement A). The output energy obtained by this method is called spark energy, Esp. Method B —using a Zener diode string for the en-ergy measurement (test arrangement B). The output energy obtained by this method is called Zener discharge energy, Ezd. This method is not suitable for systems giving alter-nating spark current. Method B is also recommended for the comparative testing of ignition coils and current interruption sys-tems.

Road vehicles. Ignition systems. Electrical performance and function test methods

KS R 5058-1995(2010) 汽车用操纵线

Control cables for automobiles

ISO 6518-2:1995 道路车辆 点火系统 第2部分:电气性能和功能试验方法

Cancels and replaces the first edition (1982). Lays down the methods and test conditions for testing battery-supplied ignition systems for spark-ignited internal combustion engines. Gives two methods of obtaining the results necessary for calculating the system output energy.

Road vehicles - Ignition systems - Part 2: Electrical performance and function test methods

JIS D 1607:1995 汽车起动机的试验方法

この規格は，自動車用内燃機関の始動に用いるスタータ(以下，スタータという。)の試験方法について規定する。

Test methods of starter motors for automobiles

SAE J2237-1995 重型起动机再制造程序，推荐做法 1995年2月

These remanufacturing procedures are recommended minimum guidelines (with the understanding that more stringent procedures are acceptable) for use by remanufacturers of heavy-duty starters to promote consistent reliability, durability, and safety of remanufactured starters. Installation of remanufactured or rebuilt products is often an economical way to repair an application even though the products may not be identical to original equipment parts. Before processing any part, a remanufacturer should determine if the original design and present condition of the core are suitable for remanufacturing so as to provide durable operation of the part as well as acceptable performance when installed on the application. The remanufacturer should also consider the safety aspects of the product and any recommendations of the original manufacturers related to remanufacturing or rebuilding their product. While these procedures are meant to be universal in application, various product types have a unique features of dimension and design which may require special remanufacturing processes and tests that are either not covered by or are exceptions to these procedures.

Heavy-Duty Starter Remanufacturing Procedures, Recommended Practice February 1995

ISO 2347:1994 道路车辆 M14×1.25矮型锥座火花塞及气缸盖安装孔

Specifies the main characteristics of, and requirements (dimensions, threads, tolerances, installation tightening torque) for the M14 * 1,25 compact spark-plugs for use with spark-ignition engines.

Road vehicles - M14×1,25 compact spark-plugs with conical seating and their cylinder head housing

ISO 2345:1994 道路车辆 M18×1.5锥座火花塞及气缸盖安装孔

Specifies the main characteristics of, and requirements (dimensions, threads, tolerances, installation tightening torque) for the M18 * 1,5 spark-plugs for use with spark-ignition engines.

Road vehicles - M18×1,5 spark-plugs with conical seating and their cylinder head housing

JIS D 5806:1994 汽车起动器开关

この規格は，自動車用スタ一タスイッチ(以下，スイッチという。)について規定する。

Starter switches for automobiles

KS R 5010-1994(1999) 汽车用分电盘安装尺度

MOUNTING DIMENSIONS OF DISTRIBUTORS FOR AUTOMOBILES

SAE J539-1993 柴油机电气装置电压

This SAE Recommended Practice is intended to apply to lamps, batteries, heaters, radios, and similar equipment for operation with mobile or automotive diesel engines. Twenty-four V systems have long been used for heavy duty services because 24 V permit operating 12 V systems in series-parallel. Thirty-two V systems have been used for marine, railroad-car lighting, and other uses. Generators, storage batteries, starting motors, lighting, and auxiliary electrical equipment shall be for nominal system ratings of 12, 24, or 32 V as determined by the power requirements of the application. It is recommended that no intermediate voltages be considered. The combination of a 24 V starting motor and two 12 V batteries connected in series for cranking is considered practice where it can be adapted to the installation. The batteries are reconnected in parallel for charging from a 12 V generator/ alternator and for operating lights and other auxiliary equipment, or charged separately and used individually for lights and other electrical equipment.

Voltages for Diesel Electrical Systems

JIS D 5204:1993 道路车辆.起动机小齿轮及环形齿轮的尺寸

この規格は，自動車に用いるスタ一タのピニオン及びリングギャのモジュール，圧力角，歯数及びその他の歯車諸元について規定する。

Road vehicles -- Dimensions of starter pinions and ring gears

ANSI/SAE J539-1993 柴油机电气系统的电压

Electrical Systems, Voltages for Diesel

SAE J1310-1993 柴油机点击预热器和电池加热器信息报告,1993年6月

The scope of this SAE Information Report is to acquaint and inform those concerned with cold weather operation of diesel powered machines and vehicles with the selection and application of electrically powered starting aids currently available. It deals specifically with the design, function, and application of line voltage electrically powered engine preheaters and battery warmers.

Electric Engine Preheaters and Battery Warmers for Diesel Engines, Information Report June 1993

ANSI/SAE J973-1993 点火装置测量程序

Ignition System Measurements Procedure

JIS D 2102:1993 汽车用膨胀塞

この規格は，自動車に使用する打込みプラグ(以下，プラグという。)について規定する。

Expansion plugs for automobiles

SAE J2073-1993 汽车起动机再制造程序

These remanufacturing procedures are recommended minimum guidelines for use by remanufactures of light-duty automotive starters to promote consistent reliability, durability, and safety of remanufactured starters. Installation of remanufactured or rebuilt products is often an economical way to repair a vehicle even though the products may not be identical to original equipment parts. Before processing any part, a remanufacturer should determine if the original design and present condition of the core are suitable for remanufacturing so as to provide durable operation of the part as well as acceptable performance when installed on the vehicle. The remanufacturer should also consider the safety aspects of the product and any recommendations of the original manufacturers related to remanufacturing or rebuilding their product. While these PROCEDURES are meant to be universal in application, various product types have unique features of dimension and design which may require special remanufacturing processes and tests that are either not covered by or are exceptions to these PROCEDURES.

Autmotive Starter Remanufacturing Procedures