43.180 检查、维修和试验设备 标准查询与下载
共找到 593 条与 检查、维修和试验设备 相关的标准，共 40 页
本标准规定了汽车积碳清洗机行业经营服务的要求、管理与验收的依据。 本标准适用于采用压滤机式电解槽技术，在液态纯净水中加入介质电解后，制取氢气和氧气的混合气体，用于氢氧气产气量不大于4000L/h的汽车除碳。
Vehicle decarbonization system
- ICS
- 43.180
- CCS
- T00/09
- 发布
- 2012-08-01
- 实施
- 2012-11-01
Road vehicles. Diagnostic communication over K-Line (DoK-Line). Physical layer
- ICS
- 43.180
- CCS
- R17
- 发布
- 2012-06-30
- 实施
- 2012-06-30
This part of ISO 14230 specifies the physical layer, based on ISO 9141, on which the diagnostic services will be implemented. It is based on the physical layer described in ISO 9141-2, but expanded to allow for road vehicles with either 12 V d.c. or 24 V d.c. voltage supply. NOTE In this part of ISO 14230, values given in parentheses apply to 24 V d.c. systems.
Road vehicles - Diagnostic communication over K-Line (DoK-Line) - Part 1: Physical layer
- ICS
- 43.180
- CCS
- T07
- 发布
- 2012-06
- 实施
Test conditions for vehicle safety technology at highway passenger stations
- ICS
- 43.180
- CCS
- R 10
- 发布
- 2012-04-28
- 实施
- 2012-06-10
Comprehensive performance testing of commercial vehicles Vehicle appearance and chassis inspection methods and evaluation
- ICS
- 43.180
- CCS
- R 86
- 发布
- 2012-04-28
- 实施
- 2012-06-10
Safety Technical Requirements for Road Transport of Dangerous Goods
- ICS
- 43.180
- CCS
- R 12
- 发布
- 2012-04-28
- 实施
- 2012-06-10
Automobile secondary maintenance quality specification
- ICS
- 43.180
- CCS
- R 16
- 发布
- 2012-04-28
- 实施
- 2012-06-10
Completion Technical Conditions for Automobile Minor Repair
- ICS
- 43.180
- CCS
- T 40
- 发布
- 2012-04-28
- 实施
- 2012-06-10
Specifications for evaluation of testing capabilities of automobile comprehensive performance testing stations
- ICS
- 43.180
- CCS
- T 40
- 发布
- 2012-04-28
- 实施
- 2012-06-10
Automobile maintenance service quality specification
- ICS
- 43.180
- CCS
- R 16
- 发布
- 2012-04-28
- 实施
- 2012-06-10
Specifications for the operation and service of automobile comprehensive performance testing stations
- ICS
- 43.180
- CCS
- T 40
- 发布
- 2012-04-28
- 实施
- 2012-06-10
This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This SAE Recommended Practice is intended as a guide toward implementation of a standard practice but may be subject to frequent change to keep pace with experience and technical advances. This should be kept in mind when considering its use. The SAE band friction test method is used to evaluate the frictional characteristics of automatic transmission band friction materials with automatic transmission fluids. It can also be used to conduct durability tests on wet friction materials.
SAE Band Friction Test Machine Guidelines
- ICS
- 43.180
- CCS
- T21
- 发布
- 2012-03-19
- 实施
- 2013-09-13
This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This SAE Recommended Practice is intended as a guide toward implementation of a standard practice but may be subject to frequent change to keep pace with experience and technical advances. This should be kept in mind when considering its use. The SAE No. 2 Friction Test Machine is used to evaluate the friction characteristics of automatic transmission plate clutch with automotive transmission fluids. It can also be used to conduct durability tests on wet friction systems. This document is intended for common use by both suppliers and end users to deine minimum test machine requirements to allow objective comparisons for wet friction material system performance.
SAE No. 2 Clutch Friction Test Machine Guidelines
- ICS
- 43.180
- CCS
- R17
- 发布
- 2012-03-19
- 实施
- 2013-09-13
This document specifies the vehicle communication interface and test equipment requirements regarding thephysical and data link layer based on IEEE 802.3 100BaseTx.This interface serves as the physical basis for Internet Protocol based communication between the vehicleand test equipment. Therefore the following aspects are specified in the clauses of this document:. signal and wiring schematics requirements to ensure physical layer compatibility of the vehicle interfaceand Ethernet networks and test equipment communication interfaces,. activation and deactivation of the diagnostic Ethernet interface and. mechanical and electrical diagnostic connector requir
Road vehicles - Diagnostic communication over Internet Protocol (DoIP) - Part 3: Wired vehicle interface based on IEEE 802.3
- ICS
- 43.180
- CCS
- 发布
- 2012-03-01
- 实施
- 2012-03-01
The scope of this document is to describe the general use-cases and communication scenarios which shall becovered by an Internet Protocol based vehicle communication standard. Each use-case drives specificcommunication capabilities of the vehicle communication interface e.g. in order to be interoperable in anexisting computer network.The diagnostic communication over Internet Protocol (DoIP) protocol supports the standardized serviceprimitive interface as specified in ISO 14229-2.This part of ISO 13400 provides the transport protocol and network layer services to support differentapplication layer implementations like:. Enhanced vehicle diagnostics (system
Road vehicles - Diagnostic communication over Internet Protocol (DoIP) - Part 1: General information and use case definition
- ICS
- 43.180
- CCS
- 发布
- 2012-02-03
- 实施
- 2012-02-03
Garage equipment. Safety requirements and methods of inspection
- ICS
- 43.180
- CCS
- 发布
- 2012
- 实施
- 2014-01-01
This SAE Recommended Practice establishes uniform procedures for evaluating conformity between the actual and target drive speeds for chassis dynamometer testing utilizing standard fuel economy and emissions drive schedules.
Drive Quality Evaluation for Chassis Dynamometer Testing
- ICS
- 43.180
- CCS
- R17
- 发布
- 2011-11-30
- 实施
- 2014-01-28
This European Standard applies to stationary, mobile and movable vehicle lifts, which are not intended to lift persons but which are designed to raise vehicles totally, for the purpose of examining and working on or under the vehicles whilst in a raised position. The vehicle lift may consist of one or more lifting-units. Power supply to the vehicle lift by internal combustion engines is not considered. The floor or ground supporting the vehicle lift in use is assumed to be horizontal. This document is not applicable to vehicle lifts which are manufactured ½ year after the date of its publication as EN.
Vehicle lifts
- ICS
- 43.180
- CCS
- 发布
- 2011-10-12
- 实施
本标准规定了机动车维修服务的总要求、维修服务流程、服务质量管理及服务质量控制等内容。 本标准适用于汽车整车维修企业和发动机、车身、电气系统、自动变速器专项维修业户，其他的机动车维修企业可参照执行。
Service specification for motor vehicle maintenance and repair
- ICS
- 43.180
- CCS
- R16
- 发布
- 2011-10-08
- 实施
- 2012-01-10
