43.180 检查、维修和试验设备 标准查询与下载

JT/T 123-2007 气缸体轴瓦镗床

本标准规定了气缸体轴瓦镗床的分类与结构、技术要求、试验方法、检验规则以及标志、包装、运输和储存等要求。 本标准适用于修理汽车、拖拉机和摩托车等的发动机气缸体轴瓦镗床。

Cylinder bushing boring machine

SANS 1144:2007 液压千斤顶

Specifies requirements for the design, construction, performance and marking of hydraulic trolley jacks designed to raise vehicles. It does not include devices that raise entire vehicles.

Hydraulic trolley jacks

AS/NZS 2693:2007 机动车辆千斤顶

Specifies requirements for the design, construction, performance and labelling of jacks designed to raise vehicles.

Vehicle jacks

BS ISO 14229:2007 道路车辆 统一诊断服务（UDS） 规范和要求

Road vehicles. Unified diagnostic services (UDS). Specification and requirements

SAE J2779-2007 HIII 5oth男性假人的低速胸部撞击试验程序

This procedure establishes a recommended practice for performing a Low Speed Thorax Impact Test to the Hybrid III 50th Male Anthropomorphic Test Device (ATD or crash dummy). This test was created to satisfy the demand by the industry to have a calibration test which resulted in similar results to an actual low energy automotive impact test. An inherent problem exists with the current calibration procedure because the normal (6.7 m/s) thorax impact test has test corridors that are not representative to these low energy impact tests. The normal test corridors specify a displacement range of around 68 mm and the low speed displacement corridor needs to be around 25 mm. The intent of this recommended practice is to develop a low speed thorax calibration procedure for the H-III50M dummy in 25 to 30 mm deflection range.

Low Speed Thorax Impact Test Procedure for the HIII 50th Male Dummy

UL 201 BULLETIN-2007 汽车车库设备UL安全性标准.评议提交截止日期:2007年10月30日

1. Revision of the Operation - Lodgement Test in Section 32; 2. Sprinkler Assembly Load Measurement (Section 19.4); 3. Revision to Heptane Specifications (Add 5.14.1, revise 56.1.5 and 58.4.2, and delete 58.4.10); 4. Revisions to Bring Definitions in Closer Alignment with NFPA 13; 5. Revisions to Clarify Requirements and Maintain Consistency with Existing Test Practices; and 6. Miscellaneous Editorial Clarifications.

UL Standard for Safety Garage Equipment COMMENTS DUE: October 30, 2007

KS R 0112-3-2006 道路车辆 诊断系统 关键字协议 2000 第3部分：应用层

Road vehicles－Diagnostic systems－Keyword protocl 2000－Part 3：Application layer

KS R 0112-2-2006 道路车辆 诊断系统 关键字协议 2000 第2部分：数据链路层

Road vehicles－Diagnostic systems－Keyword Protocol 2000－Part 2：Data link layer

KS R 0112-1-2006 道路车辆诊断系统 关键字协议 2000 艺术 1 物理层

Road vehicles－Diagnostic systems－Keyword protocol 2000－Part 1：Physical layer

KS R 0111-2006 道路车辆-诊断系统-点火系统测试设备

Road vehicles－Diagnostic systems－Equipment for ignition systems testing

ISO 14229-1:2006 道路车辆.统一诊断设备(UDS).第1部分:规范和要求

Road vehicles - Unified diagnostic services (UDS) - Part 1: Specification and requirements

ISO 14229:2006 道路车辆.统一诊断设备(UDS).要求和规范

ISO 14229 specifies data link independent requirements of diagnostic services, which allow a diagnostic tester (client) to control diagnostic functions in an on-vehicle Electronic Control Unit (server) such as an electronic fuel injection, automatic gear box, anti-lock braking system, etc. connected on a serial data link embedded in a road vehicle. It specifies generic services which allow the diagnostic tester (client) to stop or to resume nondiagnostic message transmission on the data link. ISO 14229 does not apply to non-diagnostic message transmission or to use of the communication data link between two Electronic Control Units. It does not specify any implementation requirements. The vehicle diagnostic architecture of ISO 14229 applies to: -- a single tester (client) that may be temporarily or permanently connected to the on-vehicle diagnostic data link; and -- several on-vehicle Electronic Control Units (servers) connected directly or indirectly.

Road vehicles - Unified diagnostic services (UDS) - Specification and requirements

JIS D 8101 AMD 1:2006 汽车用便携式液压千斤顶（修改件1）

JIS D 8101:1994を，次のように改正する。

Portable hydraulic jacks for automobiles (Amendment 1)

JIS D 8103 AMD 1:2006 汽车用便携式螺旋千斤顶（修改件1）

JIS D 8103:1994を，次のように改正する。

Portable screw jacks for automobiles (Amendment 1)

JT/T 649-2006 多功能汽车制动性能检测台

本标准规定了多功能汽车制动性能检测台的产品型号、技术要求、试验方法、检验规则及标志、包装、运输和贮存等。 本标准适用于检测常规制动系及防抱死等多项功能的汽车制动性能检测台。

Multi-function automobile brake tester

JTG B03-2006 公路建设项目环境影响评价规范

1.0.1 为了落实《中华人民共和国环境保护法》、《中华人民共和国环境影响评价法》、《中华人民共和国水土保持法》和《中华人民共和国公路法》等法律法规要求，促进公路交通行业可持续发展，统一公路建设项目环境影响评价的基本原则、内容、方法和要求，保证公路建设项目环境影响评价质量，特制定本规范。 1.0.2 公路建设项目环境影响评价应结合公路的工程特点、所在区域的环境特征及环境区划，突出重点、兼顾一般，并根据公路建设规模和所在地区环境敏感程度，合理确定环境评价工作的总体要求。 1.0.3 本规范适用于需编制报告书的信件或改扩建的高速公路、一级公路和二级公路建设项目的环境影响评价，其他等级的公路建设项目环境影响评价可参照执行。 1.0.4 评价分为现状评价和预测评价，预测评价包括施工期和运营近、中期。环境敏感或环境管理有要求时，对必要的环境要素可以进行远期预测。 1.0.5 公路建设项目环境影响评价除应符合本规范外，还应符合国家现行的有关标准的规定。

Specification for Environmental Impact Assessment of Highways

SAE J286-2006 SAE 2 号离合器摩擦试验机指南

This SAE Recommended Practice is intended as a guide toward implementation of a standard practice but may be subject to frequent change to keep pace with experience and technical advances. This should be kept in mind when considering its use. The SAE No. 2 Friction Test Machine is used to evaluate the friction characteristics of automatic transmission plate clutch with automotive transmission fluids. It can also be used to conduct durability tests on wet friction systems. This document is intended for common use by both suppliers and end users to deine minimum test machine requirements to allow objective comparisons for wet friction material system performance.

SAE No. 2 Clutch Friction Test Machine Guidelines

UL 201 BULLETINS-2006 CSDS 03/17/2006 (2p)

1. Revision of the Operation - Lodgement Test in Section 32; 2. Sprinkler Assembly Load Measurement (Section 19.4); 3. Revision to Heptane Specifications (Add 5.14.1, revise 56.1.5 and 58.4.2, and delete 58.4.10); 4. Revisions to Bring Definitions in Closer Alignment with NFPA 13; 5. Revisions to Clarify Requirements and Maintain Consistency with Existing Test Practices; and 6. Miscellaneous Editorial Clarifications.

CSDS 03/17/2006 (2p)

KS R 4040-2005(2015) 汽车空运

Airlifts for automobiles

KS R 4040-2005 汽车用空气起重机

이 규격은 압축 공기에 의하여 자동차의 한쪽을 승강시키는 이동식의 에어 리프트(이하, 리프

Airlifts for automobiles