47.020.05 造船用材料和零件 标准查询与下载

ANSI/ABYC T-1-2010 船和游艇应用的铝材料

This technical information report provides information on the use of aluminum for constructing outboard boats using riveted construction, outboard boats using welded construction, and inboard powered boats and yachts using welded construction.

Aluminum Applications for Boats and Yachts

ASTM F940-99(2009) 船舶建造和造船用防护涂层（涂料）的质量控制接收检验程序的标准实施规程

Standard Practice for Quality Control Receipt Inspection Procedures for Protective Coatings (Paint), Used in Marine Construction and Shipbuilding

SAE J1527-2008 航海燃油软管

This SAE Standard specifies requirements for two types, three classes and four styles of reinforced hose and non-reinforced tubing for conveying gasoline or diesel fuel aboard small craft including pleasure craft whose fuel systems are regulated under 33 CFR 183 Subpart J. Refer to SAE J 1942 Hose and Hose Assemblies for commercial marine nonmetallic flexible hose or hose assemblies used in systems on board commercial vessels inspected and certified by the U.S. Coast Guard. Refer to SAE J 2046 Personal Watercraft Fuel Systems for fuel hose used on Personal Watercraft.

Marine Fuel Hoses

ANSI/ABYC H-3-2008 外窗、挡风玻璃、舱口、门、舱门窗户和玻璃窗材料

This standard is a guide for the design, construction, and installation of exterior windows, windshields, hatches, port lights, doors, and all glazing materials on boats.

Exterior Windows, Windshields, Hatches, Doors, Port Lights, and Glazing Materials

CB 595-2008 高压空气直角节流阀规范

本规范规定了高压空气直角节流阀（以下简称节流阀）的要求、质量保证规定及交货准备等。 本规范适用于潜艇压缩空气系统用节流阀的设计、制造和验收。

Specification for high air right-angle throttle valve

CB 813-2008 鱼雷焊接通用技术条件

本标准规定了鱼雷产品熔焊（包括焊条电弧焊、埋弧焊、二氧化碳气体保护焊、钨极氩极氩弧焊和熔化极氩弧焊）焊接接头的一般要求、工艺、质量、缺陷修整和检验要求。 本标准适用于鱼雷产品用结构钢及不锈钢、铝及铝合金、钛及钛合金焊接件的焊接。

General specification for torpedo weldings

CB 1124-2008 舰船用高强度船体结构钢焊接材料的鉴定、出厂和进货检验规则

本标准规定了船舶用屈服强度下小于355MPa的高强度船体结构钢焊接材料（以下简称焊接材料）的鉴定、出厂检验和进货检验的一般要求。 本标准适用于手工电弧焊焊条、埋弧焊焊条和焊剂、气体保护焊焊丝（含药芯焊丝）等焊接材料的鉴定检验、出厂检验和进货检验。

Inspection regulation of identification,manufacture and stock on welding consumables for high strength hull structural steel of ship

CB 1140-2008 潜望镜镜管毛坯规范

本规范规定了潜艇潜望镜镜管毛坯（以下简称毛坯）的要求、质量保证规定和交货准备等。 本规范适用于各型潜艇潜望镜镜管毛坯的设计、生产和验收。

Specification for rough of submarine periscope tube

CB 1416-2008 舰船用铜合金锻件超声波检测

本标准规定了铜合金锻件超声波检测的一般要求、试块、检测条件和灵敏度调整、缺陷的评定、质量等级及检测报告等。 本标准适用于A型脉冲反射式超声波检测方法对厚度大于等于12mm的铜合金锻件超声波检测。

Ultrasonic inspection for copper alloy forgings of ship

CB/T 4106-2008 填料式伸缩接头

本标准规定了填料式伸缩接头（以下简称伸缩接头）的分类、要求、试验方法、检验规则、标志和包装。 本标准适用于温度不高于205℃的民用船舶蒸汽管路系统伸缩接头的设计、制造和验收。

Expansion joints of sleeve type

CB 1417-2008 舰船用铜合金锻件渗透检测

本标准规定了铜合金锻件渗透检测的一般要求、试块、检测、显示分类和缺陷等级评定及检测报告等。 本标准适用于铜合金锻件的表面开口缺陷的检测，其他铜合金压力加工制品表面开口缺陷的检测也可参考本标准执行。

Liquid penentrant inspection for copper alloy forgings of ship

CB 1389-2008 舰船用液压泵站规范

本标准规定了舰船用液压泵站（以下简称泵站）的要求、质量保证规定和交货准备等。 本规范适用于以石油基液压油为工作介质的泵站的研制、生产及验收。

Specification for hydraulic fluid power units of ships

CB 1399-2008 舰船用低噪声液压泵规范

本规范规定了舰船用轴向柱塞式、子母叶片式、柱销叶片式和内啮合齿轮式低噪声液压吵泵（以下简称泵）的要求、质量保证规定和交货准备等。 本规范适用于以石油基矿物为工作介质的泵的设计、制造和验收。

Specification of low noise hydraulic pump for ship

CB 1398-2008 舰船用滑油、燃油滤清器规范

本标准规定了舰船用滑油、燃油滤清器（以下简称滤清器）的要求、质量保证规定和交货准备等。 本标准适用于工作介质为滑油、燃油的全流式滤清器的设计、制造和验收。

Specification for lubricating oil and fuel oil filters of ships

CB 1390-2008 舰用柴油机排气系统消声器规范

本规范规定了舰用柴油机排气系统消声器（以下简称消声器）的要求、质量保证规定和交货准备。 本规范适用于消声器的研制、生产和验收。

Specification of exhaust system silencers of ship diesel engine

DIN 80200:2007 造船用钢制部件.表面预处理、预涂底漆和底漆涂层用符号

Steel components for shipbuilding - Symbols used for surface preparations, shop primers and priming coats

ANSI/ASTM F718:2007 造船厂和船舶漆及涂料制品/工艺数据单用规范

The Shipbuilders and Marine Paints and Coatings Product/Procedure Data Sheet provides on one sheet needed information concerning the characteristics of a specific paint or coating to include generic description, physical properties, surface preparation requirements, application requirements, and safety. The front side of the sheet contains four major, numbered paragraphs and a highlighted section for Special Safety Precautions. These paragraphs are as follows: I. Generic Type and Description II. Manufacturers Data III. Properties IV. Surface Preparation Minimum Requirements The back side of the page contains the following paragraphs: V. Mixing Procedure VI. Application The completed data sheets can be used by technical personnel to help evaluate the technical acceptability of a proposed material, by production personnel to evaluate production compatibility of proposed materials and to provide application instructions for selected paints and coatings materials, and by quality control personnel to verify attributes of materials.

Specification for Shipbuilders and Marine Paints and Coatings Product/procedure Data Sheet

ASTM F718-07 造船和船舶油漆和涂料标准产品/程序数据表

1.1 The Shipbuilders and Marine Paints and Coatings Product/Procedure Data Sheet provides on one sheet needed information concerning the characteristics of a specific paint or coating to include generic description, physical properties, surface preparation requirements, application requirements, and safety. The front side of the sheet contains four major, numbered paragraphs and a highlighted section for Special Safety Precautions. These paragraphs are as follows:I. Generic Type and DescriptionII. Manufacturers DataIII. Properties IV. Surface Preparation Minimum RequirementsThe back side of the page contains the following paragraphs:V. Mixing ProcedureVI. Application1.2 The completed data sheets can be used by technical personnel to help evaluate the technical acceptability of a proposed material, by production personnel to evaluate production compatibility of proposed materials and to provide application instructions for selected paints and coatings materials, and by quality control personnel to verify attributes of materials.

Standard for Shipbuilders and Marine Paints and Coatings Product/Procedure Data Sheet

ANSI/NAAMM FP1001-2007 金属标杆的设计指导规范

Standard provides a method to determine size of flagpole based on wind load on both pole and flag. Calculation procedure utilizes charts and tables based on variables including wind speed, height of pole, pole material, and flag size.

Guide Specifications for Design of Metal Flagpoles

SNI 7363-2007 小船用非防风雨钢门

Non weather tight steel doors for small ships