47.020.05 造船用材料和零件 标准查询与下载

SNI 7361-2007 轮船用非水密门

Ship non-watertight steel doors

SNI 7362-2007 小船用防风雨钢门

Weathertight steel doors for small ships

KS V ISO 538:2006 船舶管系安装图常用符号

이 규격 즉, 권고사항은 선박의 배관 시스템의 설치에 사용하는 통상적인 부호를 포함한다.

Conventional signs to be used in schemes for the installations of pipeline systems in ships-Recommendation

KS V ISO 538-2006(2016) 船舶管道系统安装方案中使用的常规标志建议

Conventional signs to be used in schemes for the installations of pipeline systems in ships－Recommendation

KS V ISO 644-2006(2021) 船舶通风系统安装方案中使用的常规标志－建议

Conventional signs to be used in schemes for the installations of ventilation systems in ships－Recommendation

KS V ISO 538-2006(2021) 船舶管道系统安装方案中使用的常规标志－建议

Conventional signs to be used in schemes for the installations of pipeline systems in ships－Recommendation

KS V ISO 784-2006(2021) 船舶卫生系统安装方案中使用的常规标志－建议

Conventional signs to be used in schemes for the installations of sanitary systems in ships－Recommendation

KS V ISO 644-2006(2016) 船舶通风系统安装方案中使用的常规标志建议

Conventional signs to be used in schemes for the installations of ventilation systems in ships－Recommendation

KS V ISO 644:2006 用于船舶通风系统安装设计图的常规符号

이 규격 즉, 권고 사항은 선박의 환기 시스템의 설치 계통도에 사용하는 통상적인 부호를 포

Conventional signs to be used in schemes for the installations of ventilation systems in ships－Recommendation

KS V ISO 784-2006(2016) 船舶卫生系统安装方案中使用的常规标志建议

Conventional signs to be used in schemes for the installations of sanitary systems in ships－Recommendation

SAE J1781-2006 船舶系统和液压系统的设备材料

The purpose of this Recommended Practice is to define materials for use in fluid systems of marine vehicles, including submersibles and advanced surface craft. This report is more particularly directed to the designer of fluid power and piping systems on board marine vehicles. The scope of this Recommended Practice is to delineate groups of materials for which there is considerable fabrication and operating experience in the sea water environment. In addition, some of the more promising materials for possible future applications are covered.

Ship Systems and Equipment - Materials for Fluid Systems

SAE J1527-2006 航海燃料软管

This SAE Standard specifies requirements for two types, two classes and three styles of reinforced hose for conveying gasoline or diesel fuel aboard small craft including pleasure craft whose fuel systems are regulated under 33 CFR 183 Subpart J. Refer to SAE J 1942 Hose and Hose Assemblies for commercial marine nonmetallic flexible hose or hose assemblies used in systems on board commercial vessels inspected and certified by the U.S. Coast Guard.

Marine Fuel Hoses

KS V 4031-2005(2010) 海洋旋转

Swivel for marine use

CB 853-2005 P 3.0 MPa 法兰铸钢截止阀规范

本规范规定了法兰连接尺寸按CB 856的P3.0 MPa 的法兰铸铜截止阀（以下简称截止阀）的要求、质量保证规定和交货准备等。 本规范适用于潜艇淡水、海水、燃油、滑油等管路系统用截止阀的设计、制造和验收。

Specification for P 3.0 MPa flanged cast steel stop valve

CB 1384-2005 舰船用柴油机空气冷却器规范

本规范规定了舰船用柴油机空气冷却器（以下简称空冷器）的要求、质量保证规定和交货准备等。 本规范适用于水侧设计压力不大于0.5MPa、进口设计温度为32℃，空气侧设计压力不大于0.35MPa、设计温度不高于270℃，冷却介质为海水、被冷却介质为增压空气的空冷器的设计、制造和检验。

Specification for air cooler of ship diesel engines

CB 688-2005 舰船用手动液压滑阀操纵器规范

本规范规定了船舰用手动液压滑阀操纵器（以下简称操纵器）的要求、质量保证规定和交货准备等。 本规范适用于公称压力为10MPa的操纵器的设计、制造和验收。

Specification for handle hydraulic spool controller of ship

CB/T 3351-2005 船舶焊接接头弯曲试验方法

本标准规定了船用钢焊接接头弯曲试验的式样、样坯截取及试样制备、试验步骤和试验结果的检查等。 本标准适用于船用钢焊接接头弯曲试验。

Methods of bend tests for shipbuilding welded joint

CB 855-2005 P 3.0 MPa 法兰青铜截止止回阀规范

本规范规定了法兰连接尺寸按CB 857，工作压力为3.0 MPa 的法兰青铜截止止回阀（以下简称截止止回阀）的要求、质量保证规定和交货准备等。 本规范适用于潜艇淡水、海水、燃油、滑油等管路系统用截止止回阀的设计、制造和验收。

Specification for P 3.0 MPa flanged bronze stop check valve

CB 1375-2005 登陆舰艉部液压泵站规范

本规范规定了登陆舰艉部液压泵站（以下简称液压泵站）的要求、质量保证规定和交货准备等。 本规范适用于公称压力为20MPa，油液温度不高于65℃的液压泵站的设计、制造和验收。

Specification for stern hydraulic power pack of landing ship

CB 1377-2005 登陆舰艉部液压控制系统规范

本规范规定了登陆舰液压艉锚机控制系统和液压艉门控制系统（以下统称控制系统）的要求、质量保证规定和交货准备等。 本规范适用于控制系统的设计、制造和验收。

Specification for stern hydraulic control system of landing ship