47.020.05 造船用材料和零件 标准查询与下载

CB 1375-2005 登陆舰艉部液压泵站规范

本规范规定了登陆舰艉部液压泵站（以下简称液压泵站）的要求、质量保证规定和交货准备等。 本规范适用于公称压力为20MPa，油液温度不高于65℃的液压泵站的设计、制造和验收。

Specification for stern hydraulic power pack of landing ship

ASTM E662-05 由固体材料产生的烟雾的特定光密度的标准测试方法

1.1 This fire-test-response standard covers determination of the specific optical density of smoke generated by solid materials and assemblies mounted in the vertical position in thicknesses up to and including 1 in. (25.4 mm).1.2 Measurement is made of the attenuation of a light beam by smoke (suspended solid or liquid particles) accumulating within a closed chamber due to nonflaming pyrolytic decomposition and flaming combustion.1.3 Results are expressed in terms of specific optical density which is derived from a geometrical factor and the measured optical density, a measurement characteristic of the concentration of smoke.1.4 This test method is intended for use in research and development and not as a basis for ratings for regulatory purposes.This standard measures and describes the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products or assemblies under actual fire conditions.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.1.5 The values stated in inch-pound units are to be regarded as standard. Values stated in parentheses are for information only.

Standard Test Method for Specific Optical Density of Smoke Generated by Solid Materials

KS V ISO 3372-2005 内河船舶 蘑菇型通风机头

Inland vessels－Mushroom-type ventilator heads

KS V ISO 3372:2005 内河船舶蘑菇型通风机头

Inland vessels－Mushroom-type ventilator heads

ASTM F941-99(2005) 海洋表面处理和涂层应用检验标准实践

Standard Practice for Inspection of Marine Surface Preparation and Coating Application

ISO 21005:2004 船舶和海上技术.窗户和舷窗用热钢化安全玻璃

This International Standard specifies materials and finish, dimensions for interchangeability, tolerances, parallelism and flatness, testing, marking and designation of thermally toughened safety glass panes for windows complying with ISO 3903 and side scuttles complying with ISO 1751.

Ships and marine technology - Thermally toughened safety-glass panes for windows and side scuttles

CB 871-2004 高压减震接管规范

本规范规定了舰艇液压及空气系统用高压减振接管的要求、质量保证规定和交货准备。 本规范适用于接管的设计、制造和验收。

Specifications for high pressure damping connection

ASTM A131/A131M-04 船用结构钢标准规范

1.1 This specification covers structural steel plates, shapes, bars, and rivets intended primarily for use in ship construction.1.2 Material under this specification is available in the following categories: 1.2.1 Ordinary StrengthGrades A, B, D, CS, and E with a specified minimum yield point of 34 ksi [235 MPa], and1.2.2 Higher StrengthGrades AH, DH, EH, and FH with specified minimum yield points of either 46 ksi [315 MPa], 51 ksi [350 MPa], or 57 ksi [390 MPa]. 1.3 Shapes and bars are normally available as Grades A, AH32, or AH36. Other grades may be furnished by agreement between the purchaser and the manufacturer. 1.4 When the steel is to be welded, it is presupposed that a welding procedure suitable for the grade of steel and intended use or service will be utilized. See Appendix X3 of Specification A 6/A 6M for information on weldability. 1.5 The values stated in either inch-pound units or SI units are to be regarded separately as the standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with this specification.

Standard Specification for Structural Steel for Ships

SAE J1527-2004 船用燃油软管 R（2000）

This SAE Standard specifies requirements for two types, two classes and three styles of reinforced hose for conveying gasoline or diesel fuel aboard small craft including pleasure craft whose fuel systems are regulated under 33 CFR 183 Subpart J. Refer to SAE J 1942 Hose and Hose Assemblies for commercial marine nonmetallic flexible hose or hose assemblies used in systems on board commercial vessels inspected and certified by the U.S. Coast Guard.

Marine Fuel Hoses R(2000)

CB 859-2004 P3.0MPa焊接钢法兰规范

本规范规定了工作压力P3.0 MPa焊接钢法兰的要求、质量保证规定和交货准备。 本规范适用于水下产品的管路附件和机械设备接口法兰的设计、制造和验收。

Specification for P3.0MPa welded steel pipe flanges

CB 540-2004 舷侧杯形管节规范

本规范规定了舷侧杯形管节的要求、质量保证和交货准备等。 本规范适用于工作压力不大于3.0 MPa的管节的制造和验收。

Specification for overboard penetrator on pressure hull

CB 587-2004 黄铜通海阀规范

本規範规定了黃銅遂海商 的要求、質其保證规定和交貨維備等。 本規範适用於工作压力不大於3.0 MPa的通海閃的製造和驗收。

Specification for brass outboard valve

CB 898-2004 排污舷侧阀规范

本规范规定了工作压力为3.0 MPa排污舷侧阀的要求、质量保证规定和交货准备。 本规范适用于潜艇吹除厕所容器内污物用排污阀的设计、制造和验收。

Specification for overboard discharge

CB 858-2004 P3.0MPa焊接铜法兰规范

本规范规定了工作压力P3.0 MPa焊接铜法兰的要求、质量保证规定和交货准备。 本规范适用于水产品的管路附件和机械设备接口法兰的设计、制造和验收。

Specification for P3.0MPa welded braze pipe flanges

CB/T 3955-2004 法兰不锈钢闸阀

本标准规定了法兰不锈钢闸阀的分类、要求、试验方法、检验规则、标志和包装。 本标准适用于公称压力不高于0.6 MPa，设计温度不低于-165℃的液化气体运输船、散装化学品船、舰船及其他船舶的具有腐蚀性介质的管路系统用闸阀的设计、制造和验收。

Flanged stainless steel gate valve

CB 857-2004 P3.0MPa铸铜法兰规范

本规范规定了工作压力P3.OMPa铸铜法兰的要求、质量保证规定和交货准备。 本规范适用于水下产品的管路附件和机械设备接口法兰的设计、制造和验收。

Specification for P3.0MPa cast brass pipe flanges

CB 1144-2004 P3.0MPa盲板法兰规范

本规范规定了工作压力P3.0MPa盲板法兰的要求、质量保证规定和交货准备等。 本规范适用于工作压力不大于3.0 MPa的盲板法兰的制造和验收。

Specification for P3.0MPa blank flanges

CB/T 709.2-2004 船用柴油机喷油嘴偶件技术条件

本标准规定了船用柴油机喷油器闭式喷油嘴偶件的要求、试验方法、检验规则及标志、包装、运输、贮存。 本标准适用于中、大功率的高、中速船用柴油机喷油嘴偶件的制造和验收。

Specifications for fuel injector assembly of marine diesel engine

CB/T 709.1-2004 船用柴油机喷油器总成技术条件

本标准规定了船用柴油机闭式喷油器总成的要求、试验方法、检验规则及标志、包装、运输、贮存。 本标准适用于中、大功率的高、中速船用柴油机喷油器的制造和验收。

Specifications of fuel injector assembly for marine diesel engine

CB 1372-2004 舰船滤油用高分子滤板纸规范

本截范规定了艦船油類管路系統沖洗或運行油液淨化用高分子濾板紙 的要求、 质基保证规定和交货准备等。 本规范适用于舰船上用以净化润清油、燃油、液压油等管路系统冲洗和运行油液的高分子小板纸的 制造和验收。

Specification for the hign-polymer of filter paper of filtering oil on ships