49.025.20 铝 标准查询与下载

SAE AMS4132F-2008 2.3Cu 1.6Mg 1.1Fe 1.0Ni 0.18Si 0.07Ti(2618-T61)溶解和沉淀热处理的铝合金、锻模和手制锻件、轧制环材和锻造原料

This specification covers an aluminum alloy in the form of die forgings, hand forgings, rolled rings, and forging stock. These products have been used typically for rotating parts operating in service up to 450 °F (232 °C) and other parts operating up to 600 °F (316 °C) at low stresses, but usage is not limited to such applications.

Aluminum Alloy, Die and Hand Forgings, Rolled Rings, and Forging Stock 2.3Cu 1.6Mg 1.1Fe 1.0Ni 0.18Si 0.07Ti (2618-T61) Solution and Precipitation Heat Treated

SAE AMS4090E-2008 5.7Zn,2.2Mg,1.6Cu,0.22Cr(7475-T651)溶液热处理,应力释放,和沉淀热处理的铝合金板

This specification covers an aluminum alloy in the form of plate. This plate has been used typically for structural applications requiring plate with high strength, moderate fatigue strength, and high fracture-toughness, but usage is not limited to such applications.

Aluminum Alloy, Plate 5.7Zn 2.2Mg 1.6Cu 0.22Cr (7475-T651) Solution Heat Treated, Stress Relieved, and Precipitation Heat Treated

SAE AMS4415A-2008 8.9Zn 2.2Cu 2.2Mg 0.15Zr(7136-T76511,-T76510)溶解热处理、应力消除、拉直、过于老化的铝合金模压品

This specification covers an aluminum alloy in the form of extruded bars, rods, wire, profiles (shapes) and tubing. These extrusions have been used typically for structural applications requiring a combination of high tensile and compressive strength and good corrosions resistance, but usage is not limited to such applications. Certain processing procedures may cause this product to become susceptible to stress-corrosion cracking; ARP 823 recommends practices to minimize such conditions.

Aluminum Alloy Extrusions 8.9Zn 2.2Cu 2.2Mg 0.15Zr (7136-T76511, -T76510) Solution Heat Treated, Stress-Relieved, Straightened, and Overaged

SAE AMS4178E-2008 5052、350(177)层状结构用处理的柔性蜂窝芯状铝合金

This specification covers an aluminum alloy in the form of honeycomb core in a non-hexagonal, flexible cell configuration, the core being treated for increased corrosion resistance and furnished only in the expanded form. This honeycomb core has been used typically in contoured sandwich construction for short-term service up to 350 °F (177 °C) or for long-term service up to 200 °F (93 °C), but usage is not limited to such applications.

Core, Flexible Honeycomb, Aluminum Alloy, Treated, For Sandwich Construction, 5052, 350 (177)

SAE AMS4141F-2008 5.6Zn 2.5Mg 1.6Cu 0.23Cr(7075-T73)溶解和沉淀热处理的铝合金模锻件

This specification covers an aluminum alloy in the form of die forgings and forging stock ordered to inch/pound units. These forgings have been used typically for parts requiring good resistance to stress-corrosion cracking but with lower strength than AMS 4126, but usage is not limited to such applications.

Aluminum Alloy Die Forgings, 5.6Zn 2.5Mg 1.6Cu 0.23Cr (7075-T73) Solution and Precipitation Heat Treated

SAE AMS4457-2008 3.5Cu-1.1Li-0.50Mg-0.40Ag-0.12Zr(20980-T8)溶解热处理,冷作和人工老化的铝合金薄板材

1.1 FormThis specification covers an aluminum alloy in the form of sheet.1.2 ApplicationThis product has been used for aircraft applications where if offers a combination of high strength and low density, but usage is not limited to such applications.

Aluminum Alloy, Sheet 3.5Cu-1.1Li-0.50Mg-0.40Ag-0.12Zr (20980-T8) Solution Heat Treated, Cold Worked, and Artificially Aged

SAE AMS4416-2008 2.9Cu-1.7Li-0.4Mg-0.4Ag-0.10Zr溶解热处理,使用拉伸和人工老化应力释放的铝合金挤压轮廓(2196-T8511)

This specification covers an aluminum-lithium alloy in the form of extruded profiles.1.2 ApplicationThese extrusions have been used typically for machined parts requiring dimensional stability during machining processes,and high strength, but usage is not limited to such applications.1.2.1 Certain processing procedures may cause this product to become susceptible to stress-corrosion cracking;ARP823 recommends practices to minimize such conditions.

Aluminum Alloy, Extruded Profiles (2196-T8511) 2.9Cu-1.7Li-0.4Mg-0.4Ag-0.10Zr Solution Heat Treated, Stress Relieved by Stretching and Artificially Aged

SAE AMS4310E-2008 5.6Zn 2.5Mg 1.6Cu 0.23Cr(7075-T651、7075-T652)溶解热处理,机械应力释放和沉淀热处理的铝合金轧制或锻制环材

1.1 FormThis specification covers an aluminum alloy in the form of rolled or forged rings.1.2 ApplicationThese rings have been used typically for high strength machined parts where good stability is required during machining,but usage is not limited to such applications. These rings are not recommended for fusion welding.1.2.1 Certain design and fabricating procedures may cause these rings to become susceptible to stress-corrosion cracking; ARP823 recommends practices to minimize such conditions.1.3 ClassificationRings are classified by type of mechanical stress relief as follows:7075-T651 Stress relieved by tension7075-T652 Stress relieved by compression1.3.1 Either type may be supplied, unless a specific type is ordered.

Aluminum Alloy, Rolled or Forged Rings, 5.6Zn-2.5Mg-1.6Cu-0.23Cr (7075-T651, 7075-T652) Solution Heat Treated, Mechanically Stress Relieved, and Precipitation Heat Treated

SAE AMS4415-2008 8.9Zn 2.2Cu 2.2Mg 0.15Zr(7136-T76511,-T76510)溶解热处理,应力释放,拉直和老化的铝合金模压品

1.1 FormThis specification covers an aluminum alloy in the form of extruded bars, rods, wire, profiles (shapes) and tubing.1.2 ApplicationThese extrusions have been used typically for structural applications requiring a combination of high tensile andcompressive strength and good corrosion resistance, but usage is not limited to such applications.1.3 Certain processing procedures may cause this product to become susceptible to stress-corrosion cracking;ARP823 recommends practices to minimize such conditions.

Aluminum Alloy Extrusions 8.9Zn-2.2Cu-2.2Mg-0.15Zr (7136-T76511, -T76510) Solution Heat Treated, Stress-Relieved, Straightened, and Overaged

SAE AMS4312D-2008 1.0Mg 0.60Si 0.28Cu 0.20Cr(6061-T651,6061-T652)溶解热处理,机械应力释放和沉淀热处理的铝合金滚压或锻制环材

1.1 FormThis specification covers an aluminum alloy in the form of rolled or forged rings.1.2 ApplicationThese rings have been used typically for structural applications requiring material with moderate strength and excellentresistance to stress-corrosion cracking and where good stability is required during machining, but usage is not limited tosuch applications. Alloy is further characterized by excellent fusion weldability.1.3 ClassificationRings covered by this specification are classified by type of mechanical stress relief as follows:Type 1 Stress relieved by stretching (6061T651)Type 2 Stress relieved by compression (6061T652)1.3.1 Either type may be supplied, unless a specific type is ordered.

Aluminum Alloy, Rolled or Forged Rings 1.0Mg-0.60Si-0.28Cu-0.20Cr (6061-T651, 6061-T652) Solution Heat Treated, Mechanically Stress Relieved, and Precipitation Heat Treated

SAE AMS4025L-2008 1.0Mg 0.60Si 0.28Cu 0.20Cr(6061-0)退火的铝合金薄板材和厚板材

1.1 FormThis specification covers an aluminum alloy in the form of sheet and plate.1.2 ApplicationThese products have been used typically for parts where moderate formability and response to solution and precipitationheat treatment are required, but usage is not limited to such applications.

Aluminum Alloy, Sheet and Plate, 1.0Mg-0.60Si-0.28Cu-0.20Cr (6061-0) Annealed

SAE AMS4027N-2008 1.0Mg 0.60Si 0.28Cu 0.20Cr(6061;-T6薄板材,-T651厚板材)溶解和沉淀热处理的铝合金薄板材和厚板材

1.1 FormThis specification covers an aluminum alloy in the form of sheet and plate.1.2 ApplicationThese products have been used typically for parts where strength is required and limited formability is acceptable, butusage is not limited to such applications.

Aluminum Alloy, Sheet and Plate 1.0Mg 0.60Si 0.28Cu 0.20Cr (6061; -T6 Sheet, -T651 Plate) Solution and Precipitation Heat Treated

SAE AMS4285D-2008 7.0Si 0.3Mg(356.0-T6)溶解和沉淀热处理离心的铝合金铸件

1.1 FormThis specification covers an aluminum alloy in the form of centrifugal castings.1.2 ApplicationThese castings have been used typically for intricate castings with thin walls or sections used at relatively high stresses,but usage is not limited to such applications.

Aluminum Alloy Castings, Centrifugal, 7.0Si 0.3Mg (356.0-T6) Solution and Precipitation Heat Treated

SAE AMS4284H-2008 7.0Si 0.30Mg(355.0-T6)溶解和沉淀热处理的永久铸模铝合金铸件

1.1 FormThis specification covers an aluminum alloy in the form of permanent mold castings.1.2 ApplicationThese castings have been used typically for components requiring low weight, moderate strength, and soundness, but usage is not limited to such applications.

Aluminum Alloy Castings, Permanent Mold 7.0Si 0.30Mg (355.0-T6) Solution and Precipitation Heat Treated

SAE AMS4281G-2008 5.0Si 1.2Cu 0.5Mg(355.0-T6)溶解和沉淀热处理永久铸模的铝合金铸件

1.1 FormThis specification covers an aluminum alloy in the form of permanent mold castings.1.2 ApplicationThese castings have been used typically for parts requiring moderate strength up to 300 °F (149 °C), but usage is not limited to such applications.

Aluminum Alloy Castings, Permanent Mold 5.0Si 1.2Cu 0.5Mg (355.0-T6) Solution and Precipitation Heat Treated

SAE AMS4280J-2008 5.0Si 1.2Cu 0.5Mg(355.0-T71)溶解热处理和老化的永久铸模铝合金铸件

1.1 FormThis specification covers an aluminum alloy in the form of permanent mold castings.1.2 ApplicationThese castings have been used typically for components requiring moderate strength and dimensional stability up to 300°F (149 °C), but usage is not limited to such applications.

Aluminum Alloy Castings, Permanent Mold, 5.0Si 1.2Cu 0.5Mg (355.0-T71) Solution Heat Treated and Overaged

SAE AMS4081J-2008 1.0Mg 0.60Si 0.28Cu 0.20Cr(6061-T4)溶解热处理和自然老化的液压拉制无缝铝合金圆管

1.1 FormThis specification covers an aluminum alloy in the form of seamless, round tubing.1.2 ApplicationThis tubing has been used typically for aircraft hydraulic systems and fuel and oil lines to be formed in the solution heattreated condition and subsequently precipitation heat treated, but usage is not limited to such applications.

Aluminum Alloy, Tubing, Hydraulic, Seamless, Drawn, Round 1.0Mg 0.60Si 0.28Cu 0.20Cr (6061-T4) Solution Heat Treated and Naturally Aged

SAE AMS4082P-2008 1.0Mg 0.60Si 0.28Cu 0.20Cr(6061-T6)溶解和沉淀热处理的拉制无缝铝合金管

1.1 FormThis specification covers an aluminum alloy in the form of seamless, drawn tubing.1.2 ApplicationThis tubing has been used typically for parts, such as brackets, conduits, and low-pressure liquid lines, requiringmoderate strength at ambient temperatures, but usage is not limited to such applications.

Aluminum Alloy, Seamless Drawn Tubing, 1.0Mg 0.60Si 0.28Cu 0.20Cr (6061-T6) Solution and Precipitation Heat Treated

SAE AMS4214J-2008 5.0Si 1.2Cu 0.50Mg溶解热处理和稳定的铝合金沙铸件

1.1 FormThis specification covers an aluminum alloy in the form of sand castings.1.2 ApplicationThese castings have been used typically for components requiring strength up to 450 °F (232 °C), but usage is not limitedto such applications.

Castings, Aluminum Alloy Sand 5.0Si 1.2Cu 0.50Mg Solution Heat Treated and Stabilized

SAE AMS4260G-2008 7.0Si 0.32Mg(356.0-T6)溶解和沉淀热处理的铝合金熔模铸件

1.1 FormThis specification covers an aluminum alloy in the form of castings.1.2 ApplicationThese castings have been used typically for components requiring low weight, moderate strength and soundness, cast toapproximately final dimensions, but usage is not limited to such applications.

Aluminum Alloy, Investment Castings 7.0Si 0.32Mg (356.0-T6) Solution and Precipitation Heat Treated