共找到 486 条与 垫圈和其他锁紧元件 相关的标准,共 33 页
The object of this test is to detail a standard test method to determine the ability of an electrical connector to operate with an acceptable level of partial discharge at working voltages up to the extinction voltage.
TP-44A Corona Test Procedure for Electrical Connectors
This International Standard specifies the diameters of lockwire. This International Standard is applicable to the compilation of aerospace product standards.
Aerospace - Lockwire - Diameters
This section specifies the Logical Link Control (LLC) Sublayer protocol data unit (PDU) structure for the CEBus Network. The LLC PDU (LPDU) is the unit of data exchanged between peer LLC entities. The LPDU consists of an "LPDU Header" and an "LLC Service Data Unit" (LSDU). The LSDU may be a Network Layer Protocol Data Unit (NPDU) to be exchanged between peer Network Layer entities. The LPDU Header is a unit of data which the LLC Sublayer appends to the LSDU to properly deliver the LSDU to its destination. Upon reception of an LPDU, the LPDU Header is stripped away by the receiving LLC Sublayer, and the LSDU is passed to the destination's Network Layer. (Note that the LPDU Header is currently null.)
Node Logical Link Control Sublayer
This specification contains all the information necessary to facilitate the exchange of data and control information over the power line medium within a home. The document is divided into six sections (1 - 6):An introduction to the PL standard. A general description of the PL network that is likely to exist in residential environments. The specifications of the allowed topology and configuration rules for constructing PL networks in the home. A specification of the PL physical medium - this section covers frequency allocation, physical and electrical specification of the medium, connectors, environmental requirements, and installation considerations.
Power Line Physical Layer and Medium Specification
This section specifies the Medium Access Control (MAC) Sublayer protocol data unit (PDU) structures for the CEBus Network. The MAC PDU (MPDU) is the unit of data exchanged between peer MAC entities. The MPDU consists of an "MPDU Header" and an "LPDU". The LPDU is the LLC Protocol Data Unit, that is the data handed down from the LLC to the MAC for transmission. (The LPDU is also referred to as a "MAC Service Data Unit" or "MSDU".) The MPDU Header is data that the MAC Sublayer appends to the LPDU to properly deliver the LPDU to its destination. Upon reception of an MPDU, the MPDU Header is stripped away by the receiving MAC Sublayer, and the LPDU (or MSDU) is passed up to the destination's LLC Sublayer.
Node Medium Access Control Sublayer
This specification provides the engineering and performance requirements for a fimily of high density blade-and-tuning fork contact printed wiring board (PWB) connectors of assessed quality designed for use in electronic and electrical equipment. It shall
Two-Part High Density Blade and Backplane Tuning Fork Connector
Pin-Lock, BrassTABLE 1 - PART NUMBERS AND DIMENSIONS
Pin-Lock, Brass
Washer, Flat - AMS 5510 FSC 5310
Washer, Flat - AMS 5510 FSC 5310
Washer, Flat - AMS 6350TABLE1 - PART NUMBERS AND DIMENSIONS
Washer, Flat - AMS 6350
WASHER, FLAT - STEEL AMS 6437 OR AMS 6485, DIFFUSED NICKEL-CADMIUM PLATED, COUNTERSUNK
WASHER, FLAT - STEEL AMS 6437 OR AMS 6485, DIFFUSED NICKEL-CADMIUM PLATED, COUNTERSUNK
Aerospace series. Washers, tab, in heat resisting steel, passivated.
This draft is now available for public comment and your views and technical comments on it would be appreciated. If you have no specific comments to make but find it generally acceptable it would be helpful if you would notify us accordingly Suggestions entailing revision of the text should indicate the preferred wording. Please quote the relevant clause number against any comment.
Aerospace Series Installation Requirements for Metric Nipples, Locked-In with a Serrated Safety Lockring Edition P1
The related documents, units, symbols, terminology, standard values, preferred values, and markings are described in sedion two of Round Style sectional specrfication EIA-540E000 and the following additional requirements. Part Numberina: Each socket desc
Detail Specification for Round Style Sockets
The instructions for the numbers in brackets below indicate the information to be inserted in the corresponding location in the blank detail specification (BDS). By inserting the appropriate information in the BDS, a specific round style socket will be de
Blank Detail Specification for Round Style Sockets
This standard specifies the characteristics of wire locking washers, in corrosion resisting steel, passivated, for aerospace applications.
Aerospace series - Washers, wire locking, in corrosion resisting steel, passivated
This standard specifies the characteristics of tab washers, in heat resisting steel, passivated, for maximum operating temperature 650°C, for aerospace applications.
Aerospace series - Washers, tab, in heat resisting steel, passivated
This standard specifies the characteristics of wire locking washers, in corrosion resisting steel, passivated, for aerospace applications.
Washers, wire locking, in corrosion resisting steel, passivated
This standard specifies the characteristics of tab washers, in heat resisting steel, passivated, for maximum operating temperature 650 ℃, for aerospace applications. Their use under hexagon head bolts is conditional upon the user accepting the possibility of some interference.
Washers, tab, in heat resisting steel, passivated
This standard specifies the characteristics of flat washers, in heat resisting steel, passivated, for maximum operating temperature 650°C, for aerospace applications.
Aerospace series - Washers, flat, in heat resisting steel, passivated
This standard specifies the characteristics of flat washers, large diameter, in heat resisting steel, passivated, for maximum operating temperature 650°C, for aerospace applications.
Aerospace series - Washers, flat, large diameter, in heat resisting steel, passivated
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号