49.035 航空航天制造用零部件 标准查询与下载
共找到 2327 条与 航空航天制造用零部件 相关的标准，共 156 页
This standard is applicable to the design, manufacture and repair of aerospace components by brazing or high- temperature brazing.
Aerospace series - Brazed and high-temperature brazed metallic components - Technical specifications; Text in German and English
- ICS
- 49.035
- CCS
- V11
- 发布
- 2009-01
- 实施
5.1 Transparent parts, such as aircraft windshields and windows, can be inspected using this practice, and the amount of optical distortion or deviation can be measured. The measurement can be checked for acceptability against the specification for the part. The photograph (digital file, print or negative) can be maintained as a permanent record of the optical quality of the part. 1.1 This photographic practice determines the optical distortion and deviation of a line of sight through a simple transparent part, such as a commercial aircraft windshield or a cabin window. This practice applies to essentially flat or nearly flat parts and may not be suitable for highly curved materials. 1.2 Test Method F801 addresses optical deviation (angluar deviation) and Test Method F2156 addresses optical distortion using grid line slope. These test methods should be used instead of Practice F733 whenever practical. 1.3 This standard does not purport to address the safety concerns associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Standard Practice for Optical Distortion and Deviation of Transparent Parts Using the Double-Exposure Method
- ICS
- 49.035
- CCS
- 发布
- 2009
- 实施
This Aerospace Standard specifies the inside diameters, cross-sections, tolerances, and size identification codes (dash numbers) for O-rings used in sealing applications and for straight thread tube fitting boss gaskets. The dimensions and tolerances specified in this standard are suitable for any elastomeric material provided that suitable tooling is available. This standard is intended to be used in the preparation of Company, Military, or other Standard Drawings for O-Rings. Each dash number, which should be appended to an appropriate Drawing or Standard number, identifies one nominal size O-Ring only. No attempt is made in this AS to indicate which of the O-Ring sizes listed under this system should be included in any particular Standard Drawing. Its only purpose is to standardize O-Ring sizes and dimensional tolerances and the means of identifying them dimensionally.
Aerospace Size Standard for O-Rings
- ICS
- 49.035
- CCS
- V21
- 发布
- 2008-12-05
- 实施
This standard specifies the rules for the marking of aerospace products. It is applicable whenever referenced in the definition document of the product.
Aerospace series - Marking of aerospace products; German and English version EN 2424:2008
- ICS
- 49.035
- CCS
- V04
- 发布
- 2008-10
- 实施
Aerospace－Eye-ends, in corrosion-resistant steel,swaged on aircraft control wire rope－Dimensions and loads
- ICS
- 49.035
- CCS
- 发布
- 2008-09-30
- 实施
Aerospace－Eye-ends, in corrosion-resistant steel,swaged on aircraft control wire rope－Dimensions and loads
- ICS
- 49.035
- CCS
- 发布
- 2008-09-30
- 实施
이 표준은 항공기 조종 와이어로프에 스웨이지하는 내식강으로 된 끝단 고리의 특성에 대한 표
Aerospace－Eye-ends, in corrosion-resistant steel,swaged on aircraft control wire rope－Dimensions and loads
- ICS
- 49.035
- CCS
- V20
- 发布
- 2008-09-30
- 实施
- 2008-09-30
이 표준은 저합금강이나 내식강으로 만들어진 항공기 조종 와이어로프의 턴배럴용 끝단 고리의
Aerospace-Eye-ends, in steel, threaded, for aircraft control wire rope-Dimensions and loads
- ICS
- 49.035
- CCS
- V20
- 发布
- 2008-09-30
- 实施
- 2008-09-30
Aerospace－Eye-ends, in steel, threaded, for aircraft control wire rope－Dimensions and loads
- ICS
- 49.035
- CCS
- 发布
- 2008-09-30
- 实施
Aerospace－Eye-ends, in steel, threaded, for aircraft control wire rope－Dimensions and loads
- ICS
- 49.035
- CCS
- 发布
- 2008-09-30
- 实施
Aerospace－Preformed flexible steel wire rope for aircraft controls－Part 2：Technical specification
- ICS
- 49.035
- CCS
- 发布
- 2008-08-29
- 实施
Aerospace－Preformed flexible steel wire rope for aircraft controls－Part 1：Dimensions and loads
- ICS
- 49.035
- CCS
- 发布
- 2008-08-29
- 实施
이 표준은 항공기 조종에 사용되는 탄소강 또는 내식 강철 재질로 된, 성형된 유연 강선 로
Aerospace-Preformed flexible steel wire rope for aircraft controls-Part 1:Dimensions and loads
- ICS
- 49.035
- CCS
- V40
- 发布
- 2008-08-29
- 实施
- 2008-08-29
Aerospace series - Marking of aerospace products
- ICS
- 49.035
- CCS
- 发布
- 2008-08-29
- 实施
- 2008-08-29
Aerospace－Preformed flexible steel wire rope for aircraft controls－Part 2：Technical specification
- ICS
- 49.035
- CCS
- 发布
- 2008-08-29
- 实施
이 표준은 항공기 조종에 사용되는 탄소강 또는 내식강 재질로 된 성형된 유연 강선 로프가
Aerospace－Preformed flexible steel wire rope for aircraft controls－Part 2：Technical specification
- ICS
- 49.035
- CCS
- V40
- 发布
- 2008-08-29
- 实施
- 2008-08-29
Aerospace－Preformed flexible steel wire rope for aircraft controls－Part 1：Dimensions and loads
- ICS
- 49.035
- CCS
- 发布
- 2008-08-29
- 实施
Packing, Preformed (PTFE) AMS 3668, Seal
- ICS
- 49.035
- CCS
- V13
- 发布
- 2008-08-11
- 实施
Aerospace series - Marking of aerospace products
- ICS
- 49.035
- CCS
- V08;V04
- 发布
- 2008-07-31
- 实施
- 2008-07-31
Aerospace－Locking clips, in corrosion resistant steel, for aircraft control wire rope turnbuckles－Dimensions
- ICS
- 49.035
- CCS
- 发布
- 2008-07-15
- 实施
