49.040 有关航空航天制造用镀涂和有关工艺 标准查询与下载

NF L10-216:2010 航空航天系列.有色铝涂层.涂覆方法

Aerospace Series - Aluminium pigmented coatings - Coating methods.

EN 2133:2010 航空航天系列.抗拉强度≤1450 Mpa的镀镉钢,铜,铜合金以及镍合金

This European Standard specifies the electrolytic cadmium plating of parts in steel of tensile strength Rm (max.)

Aerospace series - Cadmium plating of steels with specified tensile strength <= 1450 MPa, copper, copper alloys and nickel alloys

KS W ISO 1466-2009(2014) 飞机杠杆式手动开关性能要求

Lever-operated manual switches for aircraft－Performance requirements

KS W ISO 8074-2009(2019) 奥氏体不锈钢零件的航空航天表面处理

Aerospace－Surface treatment of austenitic stainless steel parts

KS W ISO 8074:2009 航空航天.奥氏体不锈钢零件的表面处理

이 표준은 오스테나이트계 스테인리스강(예를 들면 AISI 300 계열, 19-9DL 및 A

Aerospace－Surface treatment of austenitic stainless steel parts

SAE AMS2475G-2009 镁合金防护处理

This specification establishes the requirements for chromate conversion coatings on magnesium alloys. This process has been used typically to improve corrosion resistance and adherence of organic finishes but usage is not limited to such applications. The dichromate treatment may not be suitable for alloys with high manganese content. The chrome pickle treatment has been used as touch-up for previously dichromate-treated surfaces and for improving corrosion protection temporarily, but usages are not limited to such applications.

Protective Treatments Magnesium Alloys

LST EN 4474-2009 航空航天系列铝着色涂料涂装方法

Aerospace series - Aluminium pigmented coatings - Coating methods

DIN EN 4474:2009 航空航天系列.铝涂层.涂层方法.德文和英文版本EN 4474-2009

This standard defines the coating methods and characteristics of aluminium pigmented coatings to EN 4473 which may be applied to fasteners in titanium, titanium alloys, heat resisting nickel base or cobalt base alloys and corrosion resisting steels excluding high strength steels above 1 550 MPa.

Aerospace series - Aluminium pigmented coatings - Coating methods; German and English version EN 4474:2009

SAE AMS2491E-2009 准备用于粘接的聚四氟乙烯(PTFE)的表面处理

This specification covers the engineering requirements for preparing surfaces of polytetrafluoroethylene (PTFE) for bonding and the properties resulting from the treatment.

Surface Treatment of Polytetrafluoroethylene (PTFE), Preparation for Bonding

SAE AMS-QQ-P-416C-2009 镀镉(电沉积)

This specification covers the requirements for electrodeposited cadmium plating.

Plating, Cadmium (Electrodeposited)

DS/EN 4474:2009 航空航天系列铝着色涂料涂装方法

This standard defines the coating methods and characteristics of aluminium pigmented coatings to EN 4473 which may be applied to fasteners in titanium, titanium alloys, heat resisting nickel base or cobalt base alloys and corrosion resisting steels excluding high strength steels above 1 550 MPa.

Aerospace series - Aluminium pigmented coatings - Coating methods

SAE AMS2480H-2009 磷化处理底漆

This specification covers the engineering requirements for producing a zinc phosphate coating on ferrous alloys and the properties of the coating. This process has been used typically to produce a coating which will ensure satisfactory paint adherence, but usage is not limited to such applications.

Phosphate Treatment Paint Base

SAE AMS3158C-2009 LOX相容性水基荧光渗透剂溶液

This specification covers a stable, noncorrosive, water-soluble, highly-penetrating, fluorescent solution which may, but need not, be diluted with an appropriate amount of water for use. This product has been used typically for use in fluorescent penetrant inspection of parts and assemblies for detection of surface discontinuities and imperfections, particularly on parts, such as those in oxygen systems, which must not be exposed to oils, but usage is not limited to such applications.

Solution, Fluorescent Penetrant, Water Base for LOX Compatibility

SAE AMS-QQ-N-290B-2009 镀镍(电镀)

AMS-QQ-N-290B has been reinstated to cover previously qualified products. New design applications are encouraged to consider AMS2403 and AMS2423. These products have been used typically for electrodeposited nickel plating on steel, copper and copper alloys, and zinc and zinc alloys, but usage is not limited to such applications. The original issue of this document was taken directly from U.S. Military Specification QQ-N-290A and contained only minor editorial and format changes required to bring it into conformance with the publishing requirements of SAE technical standards. The initial release of AMS-QQ-N-290 is intended to replace QQ-N-290A. Any part numbers established by the original specification remain unchanged. The original Military Specification was adopted as an SAE standard under the provisions of the SAE Technical Standards Board (TSB) Rules and Regulations (TSB 001) pertaining to accelerated adoption of government specifications and standards. TSB rules provide for (a) the publication of portions of unrevised government specifications and standards without consensus voting at the SAE Committee level, and (b) the use of the existing government specification or standard format. Under Department of Defense policies and procedures, any qualification requirements and associated qualified products lists are mandatory for DOD contracts. Any requirement relating to qualified products lists (QPL's) has not been adopted by SAE and is not part of this SAE technical document.

Nickel Plating (Electrodeposited)

EN 4474:2009 航空航天系列.铝涂层.涂层方法

This standard defines the coating methods and characteristics of aluminium pigmented coatings to EN 4473 which may be applied to fasteners in titanium, titanium alloys, heat resisting nickel base or cobalt base alloys and corrosion resisting steels excluding high strength steels above 1550 MPa.

Aerospace series - Aluminium pigmented coatings - Coating methods

SAE AMS2481H-2009 防磨损磷酸盐处理

This specification covers the requirements for a manganese phophate coating on ferrous alloys. This process has been used typically to produce a coating that will minimize chafing of contacting steel surfaces and retain an oil film, but usage is not limited to such applications.

Phosphate Treatment Antichafing

SAE AMS2466B-2009 高压镁合金碱性硬质阳极涂层

This specification covers the requirements for a hard anodic coating on magnesium alloys. This coating has been used typically to provide corrosion resistance and abrasion resistance to cast magnesium alloys, but usage is not limited to such applications.

Hard Anodic Coating of Magnesium Alloys Alkaline Type, High Voltage

SAE AMS2430P-2009 自动喷丸硬化

This specification covers the engineering requirements for automatic peening surfaces of parts by impingement of metallic shot, glass beads, and ceramic shot. To induce residual compressive stress in surface layers of parts, thereby increasing fatigue strength and resistance to stress corrosion cracking but usage is not limited to such applications.

Shot Peening, Automatic

NF L06-833:2009 航空航天系列.金属部件用压缩表面应力诱因的超声喷丸硬化法

Aerospace series - Ultrasonic shot peening for inducement of compressive surface stresses for metallic parts.

DIN EN 2786:2009 航空航天系列.紧固件的电解镀银

This standard specifies the electrolytic silver plating of fasteners used in aerospace applications. It shall apply whenever referenced.

Aerospace series - Electrolytic silver plating of fasteners; German and English version EN 2786:2008