49.040 有关航空航天制造用镀涂和有关工艺 标准查询与下载

EN 3840:2007 航空航天系列.涂料和清漆.技术规范

This standard defines the technical requirements for the qualification, manufacture, inspection and the delivery of paints and varnishes for use in aerospace applications. It shall be applied in conjunction with the EN material specification.

Aerospace series - Paints and varnishes - Technical specification

SAE AMS2400W-2007 镀镉

This specification covers the requirements for electrodeposited cadmium on metal parts. This process has been used typically to provide corrosion resistance to metal parts, but usage is not limited to such applications.

Plating, Cadmium

SAE AMS2451/11A-2007 钴镀涂

This specification covers the requirements for brush plating of cobalt by electrodeposition. This process has been used typically to improve corrosion and wear resistance of steel parts and to repair damaged, worn, or mismachined parts, but usage is not limited to such applications. This process is particularly useful for plating localized areas on-site, especially on large parts or assemblies, and for minimizing masking.

Plating, Brush, Cobalt

SAE AMS2427D-2007 离子蒸镀铝涂层

This specification covers the engineering requirements for ion vapor deposition (IVD) of aluminum on steel, titanium, and aluminum alloys and the properties of the deposit. This process has been used typically to provide a corrosion-resistant coating to parts operating at service temperatures up to 925 °F (496 °C) and requiring freedom from hydrogen embrittlement and solid metal embrittlement, but usage is not limited to such applications.

Aluminum Coating Ion Vapor Deposition

DIN EN 4158:2007 航空航天系列.涂料和清漆.传导层表面电阻的测量用试验方法

This standard describes a method of measurement of the electrical resistance of electrically conducting surface coatings on non—conducive parts and samples for aerospace applications． If electrical contact areas are provided，the method is also applicable on electrical conducing layers over coated with non-conducing layers．

Aerospace series - Paints and varnishes - Test method for measurement of electrical surface resistance of conductive layers; German and English version EN 4158:2006

SAE AMS2435G-2007 碳化钨钴涂层的爆震燃烧工艺

This specification covers the engineering requirements for applying tungsten carbide/cobalt coatings to metal parts by the detonation process and the properties of such coatings.

Coating, Tungsten Carbide-Cobalt Coating, Detonation Process

SAE AS4194A-2007 薄板材和带材的表面抛光术语

This SAE Aerospace Standard (AS) defines the nomenclature for surface finishes commonly used for sheet and strip in aerospace material specifications. It is applicable to steel and to iron, nickel, cobalt, and titanium base alloys.

Sheet and Strip Surface Finish Nomenclature

SAE AMS2759/8A-2007 离子氮化

This specification establishes the requirements and procedures for producing a hard, wear resistant ion nitrided surface on steel parts. The nitriding process, described herein, is applicable to alloy steels, tool steels, nitriding steels, corrosion resistant steels, and other ferrous alloys.

(R) Ion Nitriding [Superseded: SAE AMS-S-6090B, SAE AMS-S-6090A, SAE AMS-S-6090]

DIN EN 4508:2007 航空航天系列.涂料和清漆.防滑涂层的试验方法.滑动摩擦性能的测定

This standard specifies the procedure for determination of the sliding friction behaviour of an anti slip coating.

Aerospace series - Paints and varnishes - Test method for anti slip coatings - Determination of the sliding friction behaviour; German and English version EN 4508:2006

LST EN 4158-2007 航空航天系列色漆和清漆导电层表面电阻测量的试验方法

Aerospace series - Paints and varnishes - Test method for measurement of electrical surface resistance of conductive layers

DS/EN 4588:2007 航空航天系列色漆和清漆双组份冷固化聚氨酯涂料防滑

This standard specifies the requirements for a two component polyurethane top coat to be applied over top coats in line with EN 2434 to provide an anti slip surface for walkway/step areas in aerospace applications.The paint shall be formulated to meet the requirements of this standard or alternatively shall consist of material approved to and complying with the requirements the appropriate parts of EN 2434 together with a non-metallic anti slip agent.

Aerospace series - Paints and varnishes - Two component, cold curing polyurethane paint, anti slip

SAE AMS2440B-2007 涂铬钢部件的地面检验

This specification covers the requirements, procedures, and accept/reject criteria for inspecting ground chromium plated surfaces for grinder-induced damage to the chromium plate and substructure. The apecification also provides users with criteria for distinguishing between such damage and acceptable indications inherent to the chromium plate. This procedure is used for nondestructive testing of heat treated, high strength, (180 ksi (1240 MPa) or higher tensile strength), low-alloy steel parts which have ben chromium plated and subsequently ground, but usage is not limited to such applications.

(R) Inspection of Ground, Chromium Plated Steel Parts

SAE AMS2451/10A-2007 锡锌低氢脆化用电镀刷

This specification covers the engineering requirements and processes for brush plating of tin-zinc by electrodeposition. This process has been used typically to improve corrosion resistance of steel parts, to repair tin-zinc deposits and to repair damaged or worn parts, but usage is not limited to such applications.

Plating, Brush, Tin-Zinc Low Hydrogen Embrittlement

SAE AMS2431/2D-2007 高硬度(55～62 HRC)的喷丸硬化介质(ASH)铸钢丸

The complete requirements for procuring the product shall consist of this document and the latest issue of the basic specification, AMS 2431. Cast steel shot, high hardness, conforming to this specification is intended for use in peening metal surfaces to impart compressive stresses to these surfaces thereby increasing resistance to fatigue and stress-corrosion cracking. Generally, high hardness cast steel shot is used on parts of hardness 50 HRC or over.

Peening Media (ASH) Cast Steel Shot, High Hardness (55 to 62 HRC)

SAE AMS2451/9A-2007 低氢脆化锌镍电镀刷

This specification covers the engineering requirements and processes for brush plating of zinc-nickel by electrodeposition. This process has been used typically to improve corrosion resistance of steel parts operating under 500 °F (260 °C) asplated or under 250 °F (121 °C) when chromate treated, to repair zinc-nickel deposits and to repair damaged or worn parts, but usage is not limited to such applications.

Plating, Brush, Zinc-Nickel Low Hydrogen Embrittlement

SAE AMS2431/4C-2007 适合喷丸硬化介质(AWS)的不锈钢丝切丸

The complete requirements for procuring the product shall consist of this document and the latest issue of the basic specification, AMS 2431. Conditioned stainless steel cut wire shot conforming to this specification is intended for use in peening metal surfaces to impart compressive stresses to these surfaces thereby increasing resistance to fatigue and stress-corrosion cracking. Generally, conditioned stainless steel cut wire shot is used on parts where ferrous contamination is undesirable and a media of high durability is required.

Peening Media (AWS) Conditioned Stainless Steel Cut Wire Shot

SAE AMS2406L-2007 镀硬化沉积铬

This specification covers the engineering requirements for electrodeposited hard chromium plate and processing requirements. This plating has been used typically on parts for increasing abrasion resistance, increasing tool and die life, maintaining accuracy of gages, and reconditioning worn or undersized parts, but usage is not limited to such applications.

Plating, Chromium Hard Deposit

SAE AMS2431/3D-2007 洛氏硬度(45～52 HRC)调节碳钢切割线射丸冲压设备(AWCR)

The complete requirements for procuring the product shall consist of this document and the latest issue of the basic specification, AMS 2431. Conditioned carbon steel cut wire shot, regular hardness, conforming to this specification is intended for use in peening metal surfaces to impart compressive stresses to these surfaces thereby increasing resistance to fatigue and stresscorrosion cracking. Generally, regular hardness conditioned carbon steel cut wire shot is used on parts of hardness less than 50 HRC.

Peening Media (AWCR) Conditioned Carbon Steel Cut Wire Shot, Regular Hardness (45 to 52 HRC)

SAE AMS2431/1D-2007 洛氏硬度(45～52 HRC)射丸冲压铸钢(ASR)

The complete requirements for procuring the product shall consist of this document and the latest issue of the basic specification, AMS 2431. Cast steel shot, regular hardness, confirming to this specification is intended for use in peening metal surfaces to impart compressive stresses to these surfaces thereby increasing resistanct to fatigue and stress-corrosion cracking. Generally, regular hardness cast steel shot is used on parts of hardness under 50 HRC.

Peening Media (ASR) Cast Steel Shot, Regular Hardness (45 to 52 HRC)

BS EN 4588:2007 航空航天系列.涂料和清漆.防滑双组分冷加工聚氨酯涂料

This standard specifies the requirements for a two component polyurethane top coat to be applied over top coats in line with EN 2434 to provide an anti slip surface for walkway/step areas in aerospace applications. The paint shall be formulated to meet the requirements of this standard or alternatively shall consist of material approved to and complying with the requirements the appropriate parts of EN 2434 together with a non-metallic anti slip agent.

Aerospace series - Paints and varnishes - Two component, cold curing polyurethane paint, anti slip