49.040 有关航空航天制造用镀涂和有关工艺 标准查询与下载

SAE AMS2759/10A-2006 由氮化电位控制自动化气体氮化

This specification establishes requirements and procedures for generating nitrided surfaces on steel parts using a process controlled by the nitriding potential. The nitriding process described herein is used typically to produce a nitride case on carbon and alloy steels, tool steels, nitriding steels, corrosion resistant steels and other ferrous alloys. Applicable, allowance should be made for growth.

Automated Gaseous Nitriding Controlled by Nitriding Potential

SAE AMS2451/2A-2006 硬沉积低应力镍镀涂工艺

This specification covers the engineering requirements and process controls for brush plating of hard, low stress nickel by electrodeposition. This process has been used typically to provide wear resistance and to repair damaged, worn, or mismachined parts in applications requiring hardness, fatigue resistance, and service at temperatures up to 450°F (232°C) but usage is not limited to such applications.

Plating, Brush, Nickel Low Stress, Hard Deposit [Superseded: SAE AMS 2439A, SAE AMS 2439, SAE AMS 2439]

TIA-102.BADA-1-2006 APCO项目25.电话互连要求和定义

This document has been published by the Telecommunications Industry Association (TIA) in accordance with the terms and conditions provided for in a Memorandum of Understanding (MoU) executed by and between the TIA, the Association of Public Safety Commu

Project 25 Telephone Interconnect Requirements and Definitions (Voice Service) Addendum 1-Conventional Individual Calls Addendum to TIA/EIA-102.BADA

SAE AMS2451/6A-2006 铜镀涂工艺的一般要求

This specification establishes the engineering requirements and process controls for brush plating of copper by electrodeposition. It should be used, in conjunction with AMS 2451, for general purpose copper deposits. This process is used typically to repair damaged, worn, or mismachined parts and as a stop-off in carburizing and nitriding but usage is not limited to such applications.

Plating, Brush, Copper General Purpose

SAE AMS2451/7A-2006 中等硬度沉积低应力镍镀涂工艺

This specification covers the engineering requirements and process for brush plating of medium-hardness, low stress nickel by electrodeposition. It should be used, in conjunction with AMS 2451, for medium-hardness, low stress nickel deposits. This process has been used typically to provide wear resistance and to repair damaged, worn, or mismachined parts in applications requiring hardness, fatigue resistance, and service temperatures up to 450 degrees F (232 degrees C), but usage is not limited to such applications.

Plating, Brush, Nickel Low Stress, Medium-Hardness Deposit

SAE AMS2451/8A-2006 镀层和涂刷的非氰化物银一般用途

This specification covers the engineering requirements and process for brush plating of non-cyanide silver by electrodeposition. It is used, in conjunction with AMS 2451, for silver deposits. This process has been used typically to provide low electrical contact resistance, prevent galling or seizing of surfaces of parts, and corrosion protection, but usage is not limited to such applications.

Plating, Brush, Non-Cyanide Silver General Purpose

SAE AMS2451B-2006 镀层和涂刷一般要求

This specification and its supplementary detail specifications establish the requirements and process controls for electrodeposition of metals by brush plating. This process has been used typically to improve surface properties such as corrosion resistance, wear resistance, and brazeability or to repair damaged, worn, or mismachined parts, but usage is not limited to such applications. This process is particularly useful for plating localized areas on-site, especially on large parts or assemblies, and for minimizing masking.

Plating, Brush General Requirements

SAE AMS2451/5A-2006 硬化沉积三价铬镀涂工艺

This specification covers the engineering requirements and process controls for selective plating of hard chromium by electrodeposition. It should be used, in conjunction with AMS 2451, for cosmetic touch-up and for wear-resistant chromium deposits. This process has been used typically to provide a corrosion-resistant deposit with excellent wear resistance and to repair damaged, worn, or mismachined parts but usage is not limited to such applications.

Plating, Brush, Chromium Hard Deposit, Trivalent

SAE AMS2431B-2006 冲压设备.一般要求

This specification and its supplementary detail specifications cover the requirements for media to be used in controlled shot penning of metal parts. Reference to AMS 2431 with the appropriate slash number on a purchase order constitutes a requirement to conform to the applicable specification in 2.1.

Peening Media, General Requirements

SAE AMS2431/7A-2006 陶瓷喷射冲压设备

This specification, in conjunction with the general requirements covered in AMS 2431, establishes the requirements for ceramic shot, for peening of metal parts.

Peening Media Ceramic Shot

SAE AMS2431/5A-2006 表面硬化钢冲压球冲压设备

This specification, in conjunction with the general requirements covered in AMS 2431, establishes the requirements for peening balls to be used for peening of metal parts.

Peening Media Case Hardened Steel Peening Balls

SAE AMS2431/3C-2006 洛氏硬度(45～52 HRC)调节碳钢切割线射丸冲压设备

The complete requirements for procuring the product shall consist of this document and the latest issue of the basic specification, AMS 2431.

Peening Media (AWCR) Conditioned Carbon Steel Cut Wire Shot, Regular Hardness (45 to 52 HRC)

SAE AMS2451/1A-2006 一般用途镍镀涂

This specification establishes the engineering requirements and process controls for brush plating of nickel by electrodeposition. It should be used, in conjunction with AMS 2451, for general purpose nickel deposits.

Plating, Brush, Nickel General Purpose

TIA-93-B-1[E]-2006 基本试验和测量程序.检查和测量单套管多芯光纤连接器抛光角度和光纤位置

This standard provides interface compatibility specifications and technical requirements for the interfacing of a Wireless Carrier to an Exchange Carrier (EC), Interexchange Carrier (IC), International Carrier (INC), Consolidated Carrier or any other carrier element.

Wireless Telecommunications Ai ?Di Interfaces Standard–Addendum 1[E] Addendum to TIA/EIA-93-B

TIA TSB-116-A-2006 IP电话的电信IP电话设备语音质量建议

The objectives of this TSB are to provide end-to-end voice quality guidelines for North American IP Telephony and to an E-Model tutorial for IP scenarios. IP Telephony introduces several impairments, some of which are familiar and some new. The E-Model (ITU-T Recommendation G.107) is a tool that can estimate the end-to-end voice quality, taking the IP Telephony parameters and impairments into account. This TSB first describes how the E-Model handles IP Telephony impairments and then it provides general design recommendations for the best possible voice quality performance irrespective of cost, available technology or customer requirements. These recommendations are illustrated with specific IP scenarios to provide an E-Model tutorial for analyzing real networks.

Telecommunications - IP Telephony Equipment ?Voice Quality Recommendations for IP Telephony Contains Color

SAE AMS2474D-2006 低抗电覆层铝合金的化学处理

This specification establishes the engineering requirements for producing chemical-film coatings on aluminum and aluminum alloys and the properties of such coatings. Primarily for aluminum and aluminum alloys where increased corrosion resistance, improved paint adhesion, or a low-electrical resistance coating is required. Also useful for improving the corrosion resistance and paint adhesion properties of abraded or discontinuous anodized surfaces of aluminum and aluminum alloy parts.

Chemical Treatment for Aluminum Alloys, Low Electrical Resistance Coating

TIA-568-B.1-7-2006 商业建筑通信电缆标准第1部分:一般要求 附录7:使用阵列连接器保持极性的指南

After ANSI/TIA/EIA-568-B.1 was approved for publication, it was realized that there was a need to explain and illustrate the concept of maintaining optical fiber polarity using array connectors. The TIA TR-42 Engineering Committee on Premises Telecommunications Cabling Infrastructure accepted the task and assigned it to the TR- 42.8 Subcommittee, Telecommunications Optical Fiber Cabling Systems. The TR-42.8 Subcommittee cooperated with the TR-42.1 Subcommittee on Commercial Building Cabling, which is related to this activity, in preparing this document.

Commercial Building Telecommunications Cabling Standard Part 1 - General Requirements Addendum 7 ?Guidelines for Maintaining Polarity Using Array Connectors Addendum 7

SAE AMS2418G-2006 镀铜

This specification covers the requirements for electrodeposition of copper on metals and the properties of the deposit. This process has been used typically to provide an anti-seize surface, to prevent carburizing of surfaces on which carburizing is neither required nor permitted, to prevent decarburization, to enhance solderability, or to provide a source of copper for furnace brazing, but usage is not limited to such applications.

Plating, Copper

TIA-123-A-2006 电信-多线终端系统-多卖方QSIG互操作性测试的北美测试计划

This document describes the test cases for the functional testing of QSIG features for interoperability between at least two vendors’ QSIG offerings. The purpose of QSIG is to provide a standard based Private networking protocol which will allow customers with equipment from different vendors to have a fairly seamless feature operation across their mixed vendor network. In testing multi-vendor interoperability, the emphasis of testing should remain on functionality rather than protocol conformance. All tests to be performed should stay at a level where end user capabilities are being tested, and should not enter a protocol analysis phase until all attempts (administration changes, etc.) have been exhausted to successfully complete a given test. Even when a test cannot be successfully completed or unwanted results occur, all vendors involved should agree together to enter a protocol analysis phase.

Telecommunications ?Multiline Terminal Systems ?North American Test Plan for Multivendor QSIG Interoperability Testing

EN 4592:2006 航空航天系列.涂料和清漆.测定红外线反射率的试验方法

This standard specifies the method of test for determining the infrared reflectance of paints and varnishes.The test procedure determines the amount of energy reflected by the material in the range of wavelengths between 700 nanometres and 2 400 nanometres with respect to that of a standard reflectance material.The procedure is applicable to products intended for use in aerospace applications.

Aerospace series - Paints and varnishes - Test method for determination of infrared reflectance