共找到 2368 条与 航空航天用流体系统和零部件 相关的标准,共 158 页
Standard Practice for Liquid Sampling of Noncryogenic Aerospace Propellants
Aerospace series. Fluid systems. Hydraulic system tubing
BS ISO 7661 Aerospace Fluid systems. Clamp blocks for tube lines having axial alignment. Design standard and qualification testing (Metric series)
Standard Test Methods for Microscopical Sizing and Counting Particles from Aerospace Fluids on Membrane Filters
Aerospace Fluid systems — Clamp blocks for tube lines having axial alignment — Design standard and qualification testing (Metric series)
Aerospace series — Graphic symbols for schematic drawings of hydraulic and pneumatic systems and components
1 Scope This document establishes a scheme for the marking of components (other than pipelines, hoses and fittings) used in aircraft hydraulic systems, so that the correct type of fluid is readily apparent during any assembly or testing operations in workshops. The marking is not intended to serve any purpose when a component is installed in an aircraft.
Aircraft. Hydraulic components. Marking to indicate the fluid for which a component is approved
This document establishes a scheme for the marking of components (other than pipelines, hoses and fittings) used in aircraft hydraulic systems, so that the correct type of fluid is readily apparent during any assembly or testing operations in workshops. The marking is not intended to serve any purpose when a component is installed in an aircraft.
Aircraft — Hydraulic components — Marking to indicate the fluid for which a component is approved
Aerospace — Fluid systems — Clamp blocks for tube lines having axial alignment — Design standard and qualification testing — Metric series
Aerospace series — Fluid systems — Hydraulic system tubing
BS ISO 18170. Aerospace series. AC induction electric motor driven, variable delivery, hydraulic pumps. General requirements
BS ISO 14085-3. Aerospace series. Test methods for hydraulic filter elements - Part 3. Filtration efficiency and retention capacity
Aerospace-Hydraulic, pressure compensated, variable delivery pumps- General requirements for 35 000 kPa systems
1.1 This practice covers the measurement of the pH and chloride ion of water extraction of aerospace hydraulic fluids. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Standard Practice for pH and Chloride-ion Concentration of Aerospace Hydraulic Fluids
1 Scope This document specifies maximum and minimum dimensions for omega clamps (saddle clamps) installed by means of two bolts with nominal diameters of 5 mm. The specified dimensions define a dimensional envelope. This document is not an interchangeability standard. The tolerances for each type of clamp are defined in the drawings in the standards for parts.
Aerospace. Omega clamps (saddle clamps) for fluid systems. Dimensions
This document specifies maximum and minimum dimensions for omega clamps (saddle clamps) installed by means of two bolts with nominal diameters of 5 mm. The specified dimensions define a dimensional envelope. This document is not an interchangeability standard. The tolerances for each type of clamp are defined in the drawings in the standards for parts.
Aerospace — Omega clamps (saddle clamps) for fluid systems — Dimensions
Aerospace. Couplings, threaded and sealed, for fluid systems. Dimensions
Aerospace series - Clamps worm drive - Technical specification
Aerospace series -- PTFE flexible hose assembly with convoluted inner tube of a nominal pressure up to 6 800 kPa and 8°30' fitting in titanium -- Product standard
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号