53.020.30 起重设备附件 标准查询与下载

DIN EN 14502-2:2005 起重机.载人用提升设备.第2部分:升降控制台

This European Standard specifies additional requirements for the design of elevating control stations on cranes. General requirements for control stations on cranes are given in prEN 13557. This standard also specifies requirements for the driving mechanism, the supporting and suspension system and for safety devices for the elevating control station. This standard doesn't cover hazards which could occur during transport, erection, commissioning, modification, maintenance, de-commissioning or disposal. This standard doesn't apply to lifts for crane drivers.

Cranes - Equipment for the lifting of persons - Part 2: Elevating control stations; German version EN 14502-2:2005

SANS 2415:2005 一般起重用锻造卸扣.D形弓形卸扣

Specifies the general characteristics, performance and critical dimensions necessary for interchangeability and compatibility with other components, of forged dee and bow shackles in a range of sizes having working load limits from 0,63 t to 100 t, and in grades M(4), S(6) and T(8).

Forged shackles for general lifting purposes - Dee shackles and bow shackles

NF A47-270-1/A1:2005 钢丝绳吊索.安全.第1部分:普通提升设备用吊索

Steel wire rope slings - Safety - Part 1 : slings for general lifting service.

SANS 4309:2005 起重机．钢索．保养；维修；安装；检查和报废

Specifies the examination and discard criteria of wire rope applicable to cranes.The cranes may be used for hook, grabbing, magnet, ladle, excavator or stacking duties and may be operated manually, mechanically, electrically or hydraulically.

Cranes - Wire ropes - Care, maintenance, installation, examination and discard

KS B ISO 3056-2005(2010) 未校准圆钢链环起重链和链式吊索的使用和维护

Non－calibrated round steel link lifting chain and chain slings－Use and maintenance

GOST R EN 818-4-2005 升降用钢制短链条.安全性.第4部分:8级链式吊索

Short link chains for lifting purposes. Safety. Part 4. Chain slings grade 8

GOST R EN 818-1-2005 升降用钢制短链条.安全性.第1部分:接收一般要求

Short link steel chains for lifting purposes. Safety. Part 1. General requirements for acceptance

ASME B30.10-2005 吊钩

Within the general scope defined in Section I, ASME B30.10 applies to all types of hooks shown in Figs. 1 through 21 used in conjunction with equipment described in other volumes of the B30 Standard. Hooks supporting a load in a direct-pull configuration, with the load carried in the base (bowl/saddle or pin hole -- see Figs. 3 and 4) of the hook, are covered in Chapter 10-1. Hooks that do not support a load in a direct-pull configuration are covered in Chapter 10-2.

Hooks

GOST R EN 818-2-2005 升降用钢制短链条.安全性.第2部分:8级链式吊索的中等钢链

Short link steel chains for lifting purposes. Safety. Part 2. Medium tolerance steel chains for grade 8 chain slings

ASME BTH-1-2005 吊钩下部提升装置的设计

BTH-1 provides minimum structural and mechanical design and electrical component selection criteria for ASME B30.20 below-the-hook lifting devices. The provisions in this Standard apply to the design or modification of below-the-hook lifting devices. Compliance with requirements and criteria that may be unique to specialized industries and environments is outside of the scope of this Standard. Lifting devices designed to this Standard shall comply with ASME B30.20, Below-the-Hook Lifting Devices. ASME B30.20 includes provisions that apply to the marking, construction, installation, inspection, testing, maintenance, and operation of below-the-hook lifting devices. ASME BTH-1 addresses only design requirements. As such, this Standard should be used in conjunction with ASME B30.20, which addresses safety requirements. ASME BTH-1 does not replace ASME B30.20. The design criteria set forth are minimum requirements that may be increased at the discretion of the lifting device manufacturer or a qualified person.

Design of Below-the-Hook Lifting Devices

GOST R EN 818-5-2005 升降用钢制短链条.安全性.第5部分:4级链式吊索

Short link steel chains for lifting purposes. Safety. Part 5. Chain slings of grade 4

GOST R EN 818-3-2005 升降用钢制短链条.安全性.第3部分:4级链式吊索的中等钢链

Short link steel chains for lifting purposes. Safety. Part 3. Medium tolerance steel chains for grade 4 chain slings

JIS B 8812:2004 链式起重机用环节链

この規格は，チェーンブロック()，チェーンレバーホイスト()，電気チーンブロック()などに使用されるリンクチェーン(以下，チェーンという。)について規定する。注()JIS B 8802 ()JIS B 8819 ()JIS B 8815

Link chain for chain hoists

JIS B 8816:2004 提升用链式吊环

この規格は，巻上機などに使用する，溶接などの方法によって組み立てられたチエーンスリング(以下，チェーンスリング。)について規定する。

Chain slings for lifting purposes

JIS B 8841:2004 扁节链的硬度试验.链节的冲击试验方法

この規格は，リンクチェーンのじん(靭)性試験として，チェーンリンク衝撃試験方法(以下，試験方法という。)について規定する。

Toughness test of link chains -- Impact test method of chain links

NF G36-030-4:2004 纺织吊索.安全.第4部分:通用天然和人造纤维绳提升吊索

Textile slings - Safety - Part 4 : lifting slings for general service made from natural and man-made fibre ropes.

BS ISO 4309+A1:2004 起重机 绳索 维护和保养、检修和报废

Cranes - Wire ropes - Care, maintenance, installation, examination and discard

ISO 4309:2004 起重机.金属丝绳.保养、维修、安装、检查和报废

This International Standard details guidelines for the care, installation, maintenance and examination of wire rope in service on a crane, and enumerates the discard criteria to be applied to promote the safe use of the crane. This International Standard is applicable to the following types of crane, as defined in ISO 4306-1: a) cable and portal cable cranes; b) cantilever cranes (pillar jib, wall or walking); c) deck cranes; d) derrick and guy derrick cranes; e) derrick cranes with rigid bracing; f) floating cranes; g) mobile cranes; h) overhead travelling cranes; i) portal or semi-portal bridge cranes; j) portal or semi-portal cranes; k) railway cranes; l) tower cranes. This International Standard is applicable to cranes used for hook, grabbing, magnet, ladle, excavator or stacking duties, whether operated manually, mechanically, electrically or hydraulically. This International Standard is also applicable to hoists and hoist blocks which use wire rope.

Cranes - Wire ropes - Care, maintenance, installation, examination and discard

NF A47-270-3:2004 钢丝绳吊索.安全.第3部分:索环和缆绳吊索

Steel wire rope slings - Safety - Part 3 : grommets and cable-laid slings.

ISO 2415:2004 起重用锻造卸扣.D形弓形卸扣

This International Standard specifies the general characteristics of forged dee and bow shackles in a range of sizes having working load limits of from 0,32 t to 100 t and in Grades 4, 6 and 8, and presents their performance and critical dimensions necessary for their interchangeability and compatibility with other components. In the case of dee shackles for use with forged steel lifting hooks in conformance with ISO 4779 and ISO 7597, an intermediate component could be necessary for making the connection.

Forged shackles for general lifting purposes - Dee shackles and bow shackles