53.020.99 其他起重设备 标准查询与下载

DIN EN 1570-1:2012 升降台安全要求.第1部分:提供有两个固定着陆装置的升降台;德国 EN 1570-1-2011

Safety requirements for lifting tables - Part 1: Lifting tables serving up to two fixed landings; German version EN 1570-1:2011

ASME HST-1-2012 电动链式起重机的性能标准

Performance Standard for Electric Chain Hoists

GOST R 55181-2012 移动式升降工作平台. 有关特殊功能的设计, 计算, 安全要求和试验方法. 第2部分. 装有非导电(绝缘)部件的MEWP.

Mobile elevating work platforms. Design calculations, safety requirements and test methods. Part 2. MEWPs with nonconductive (insulating) components

GOST R 55180-2012 移动式升降工作平台. 设计, 计算, 安全要求和试验方法. 第1部分. 装有伸缩式防护系统的MEWP.

Mobile elevating work platforms. Design, calculations, safety requirements and test methods. Part 1. Elevating work platforms with retractable guardrail systems

ANSI/ASME HST-1-2012 电动链式起重机的性能标准

Performance Standard for Electric Chain Hoists

BS EN 1570-1:2011 升降台的安全要求.升降台有两次固定着陆

Safety requirements for lifting tables. Lifting tables serving up to two fixed landings

GSO EN 14492-1:2011 起重机 起重装置和自动起重机 第1部分：自动起重机

This European Standard is applicable to the design, information for use, maintenance and testing of power driven winches for which the prime mover is an electric motor, hydraulic motor, internal combustion motor or pneumatic motor. They are designed for the lifting and lowering of loads which are suspended on hooks or other load handling devices or for the lifting and lowering of loads on inclined planes or the exclusive pulling of loads on planes which are normally horizontal. NOTE Within the period of utilization, the place of use of a winch may be variable. As a rule, a winch is used without any additional transport movement. This European Standard is applicable to the following types of winch: a) rope winches; b) chain winches; c) belt winches, except steel belts used as hoisting media; d) traction winches. These types of winches a) to d) also include the following specific applications: - vehicle recovery winches; - winches on boat trailers; - forestry winches; - winches for stationary offshore applications; - winches for drilling applications; - winches to be used exclusively for the pulling of loads. NOTE Examples are shown in Annex A. This European Standard does not apply to: - power-driven hoists in accordance with EN 14492-2; - winches for seagoing vessels and mobile offshore units; - winches for the lifting of persons; - NGL building hoists in accordance with EN 14492-2; - winches for the handling of hot molten masses (risk covered by EN 14492-2). The significant hazards covered by this European Standard are identified in Clause 4. This European Standard does not specify additional requirements for hazards related to the use of winches in explosive atmospheres in underground works. This document applies to winches manufactured after approval by CEN with a transitional period of 2 years.

Cranes - Power driven winches and hoists - Part 1: Power driven winches

JB/T 10222-2011 防爆电动葫芦

本标准规定了防爆电动葫芦的术语和定义、分类和分组、基本参数、结构型式和型号、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于在有爆炸性气体环境1区、2区和/或可燃性粉尘环境21区、22区中工作的防爆电动葫芦（以下简称防爆葫芦）。

Explosion-proof hoists

JB/T 11101-2011 齿条千斤顶

本标准规定了齿条千斤顶的术语和定义、型式和基本参数、要求、试验方法、检验规则以及标志、包装和贮存。 本标准适用于矿山、桥梁、铁路、建筑等行业使用的机械式齿条千斤顶（以下简称千斤顶）。

Rack and pinion jacks

BS ISO 16653-3:2011 移动式升降工作平台.关于特殊部件的设计,计算,安全要求和试验方法.果园业务营运用可移动升降工作平台

Mobile elevating work platforms. Design, calculations, safety requirements and test methods relative to special features. MEWPs for orchard operations

JB/T 11169-2011 固定式升降工作平台

本标准规定了固定式升降工作平台（以下简称SEWP）的术语和定义、分类、技术要求、试验方法、检验规则、标志、包装、运输和贮存等。 本标准适用于SEWP。 本标准不适用于：电梯和液压电梯；消防和救火装置；高出作业吊篮和擦窗机；车尾起重机；移动式升降工作平台；公园游艺设备；桅柱爬升式工作平台；提升人员和材料的建筑施工升降机；飞机地面支持设备；埋杆机（起重挖穴机）；升降操作员的未知在工业卡车上的设备；桥梁检测和维护设备；库存拣选或订单拣选类设备。

Stationary elevating work platforms

CAN/CSA-Z271-2010 悬挂平台安全规则

1 Domaine d’application 1.1 Cette norme précise les exigences visant la conception, la construction, l’installation, la vérification, la mise à l’essai, l’entretien, la modification et la réparation des plateformes suspendues. 1.2 Cette norme s’applique aux plateformes suspendues qui sont a) conçues pour permettre l’accès aux surfaces extérieures et intérieures de bâtiments et autres structures ; b) munies d’un système de levage mécanique, électrique ou manuel ; et c) suspendues à un seul point, à deux points ou à des points de suspension multiples. 1.3 Cette norme ne traite pas des exigences relatives aux règles de sécurité pour le travail sur plateformes suspendues énoncées dans la CAN/CSA-Z91. 1.4 Cette norme ne s’applique pas au matériel énuméré ci-dessous : a) les plateformes de travail élévatrices automotrices et portatives, visées par la CAN/CSA-B354.1, la CAN/CSA-B354.2 et la CAN/CSA-B354.4 ; b) les plateformes de travail se déplaçant le long de mâts, visées par la CAN/CSA-B354.5 ; c) les engins élévateurs à nacelle portés sur véhicule, visés par la CSA C225, l’ANSI/SIA A92.7 et l’ANSI/SIA A92.8 ; d) les plateformes pour personnel qui sont fixées ou suspendues à la flèche d’une grue, visées par la CAN/CSA-Z150 ; e) les échafaudages, visés par la CAN/CSA-S269.2 et la CSA Z797 ; f) les monte-charges de chantier, visés par la CAN/CSA-Z185 et la CAN/CSA-Z256 ; g) les ascenseurs et monte-charge, visés par l’ASME 17.1/CSA B44 ; h) les monte-personne, visés par la CAN/CSA-B311 ; et i) les remontées mécaniques, visées par la CSA Z98. 1.5 Dans les normes CSA, le terme «doit» indique une exigence, c’est-à-dire une prescription que l’utilisateur doit respecter pour assurer la conformité à la norme ; «devrait» indique une recommandation ou ce qu’il est conseillé mais non obligatoire de faire ; et «peut» indique une possibilité ou ce qu’il est permis de faire. Les notes qui accompagnent les articles ne comprennent pas de prescriptions ni de recommandations. Elles servent à séparer du texte les explications ou les renseignements qui ne font pas proprement partie de la norme. Les notes au bas des figures et des tableaux font partie de ceux-ci et peuvent être rédigées comme des prescriptions. Les annexes sont qualifiées de normatives (obligatoires) ou d’informatives (facultatives) pour en préciser l’application. 1.6 Les mesures exprimées en unités SI (métriques) constituent la norme. On trouve à l’annexe A des équivalents en unités anglaises de ces valeurs, à titre informatif uniquement.

Safety rules for suspended platforms

GOST R 54770-2011 升降工作平台.桅杆爬升式工作平台.结构计算、安全性要求、检验方法

Elevating work platforms. Mast-climbing work platforms. Calculating of structure, safely requirements, test methods

ANSI/ASME B30.7-2011 基座固定卷筒提升机

The construction, installation, operation, inspection, testing and maintenance of winches arranged for mounting on a foundation or other supporting structure for moving loads. Winches addressed in this volume are those typically used in industrial, construction and maritime applications. The requirements included in this volume apply to winches that are powered by internal combustion engines, electric motors, compressed air or hydraulics and that utilize drums and rope.

Base Mounted Drum Hoists

ANSI/SIA A92.9-2011 美国国家桅杆攀爬工作平台标准

This standard applies to the establishment of criteria for design, manufacture, testing, inspection, installation, maintenance, use, training and operation of mast climbing work platforms that are primarily used to position personnel, along with their necessary tools and materials, to perform their work. Platforms may be adjustable by manual or powered means.

American National Standard for Mast-Climbing Work Platforms

EN 1570-1:2011 安全要求取消表-第1部分:提升表提供两个固定着陆(取代:1570年CEN PREN,CEN EN 1570）

This European Standard specifies the safety requirements for industrial lifting tables for raising and/or lowering goods and the operator(s): where the lifting table does not pass a fixed landing; serving not more than 2 fixed landings.This European Standard deals with all significant hazards pertinent to lifting tables when they are used as intended by the operating instructions and under the conditions foreseen (including foreseeable misuse) with the operating instructions (see Clause 4).This European Standard specifies the appropriate technical measures to eliminate or reduce the risks arising from the significant hazards. Both power operated and manually operated lifting tables are included whether stationary or mobile.This European Standard does not apply to the following equipment: lifting tables, serving more than 2 fixed landings of a building, for lifting goods with a vertical travel speed not exceeding 0,15 m/s (EN 1570-2); lifting tables, serving more than 2 fixed landings of a building for lifting operators, with a vertical travel speed not exceeding 0,15 m/s (EN 1570-3); lifting tables carrying operators and installed in full enclosures (EN 1570-3); permanently and temporarily installed lifting tables, serving specific levels of a building for lifting operators, with a vertical travel speed exceeding 0,15 m/s (EN 81-1 and EN 81-2); lifting tables with flat or toothed belts lifting systems for the carrying of operators; lifting tables whose vertical travel speed exceeds 0,15 m/s (unless safe by position and non person carrying); power operated lifting platforms for persons with impaired mobility (EN 81-41); mobile lifting tables for airport ground support equipment (EN 1915-2 and EN 12312-1); lifting tables which are designed as part of a lift according to Directive (95/16/EC); lifting tables used on ships; mobile elevating work platforms (EN 280); static elevating work platforms; vehicle lifts for maintenance (EN 1493); mobile lifting tables used for fire fighting (EN 1777); mobile lifting tables used as fork lift trucks and order pickers; mobile lifting tables with a horizontal travelling speed of more than 1,6 m/s; rail dependent storage and retrieval equipment (EN 528); theatre stage lifts intended to move performers; scissor lift pallet trucks (EN ISO 3691-5); suspended lifting tables; lifting tables operated by pushing chains.This standard does not establish the additional requirements for: electromagnetic compatibility; operation in severe conditions (e. g. extreme climates, freezer applications, strong magnetic fields); operation subject to special rules (e. g. potentially explosive atmospheres, mines); handling of loads, the nature of which could lead to dangerous situations (e. g. molten metal, acids, radiating materials, especially brittle loads); hazards occurring during construction, transportation and disposal; equipment installed on the load platform or replacing it; integration into systems or other machines, control from more than two control stations, etc.; cable-less controls; lifting tables where the hydraulic pressure is derived directly from gas pressure; the power supply to the lifting table by internal combustion engine.

Safety requirements for lifting tables - Part 1: Lifting tables serving up to two fixed landings (Incorporates Amendment A1: 2014)

ASME B30.20-2010 下吊钩提升装置

This document includes provisions that apply to the marking, construction, installation, inspection, testing, maintenance, and operation of below-the-hook lifting devices, other than components addressed by other ASME B30 Volumes or other standards, used for attaching loads to a hoist. This Volume covers Structural and Mechanical Lifting Devices, Vacuum Lifting Devices, Operated Close Proximity Lifting Magnets, Remotely Operated Lifting Magnets and Scrap and Material Handling Grapples.

Below-the-Hook Lifting Devices (B30.20 - 2010)

DIN EN 1808:2010 悬吊式出入通道设备的安全性要求.设计计算,稳定性标准,结构.试验.德文版本EN 1808-1999+A1-2010

Safety requirements on Suspended Access Equipment - Design calculations, stability criteria, construction - Tests; German version EN 1808:1999+A1:2010

DS/EN 12158-2+A1:2010 货物施工升降机 第2部分：带有不可触及承载装置的倾斜升降机

1.1 This standard deals with power operated temporarily installed builders hoists intended for use by persons who are permitted to enter sites of engineering and construction, serving either one upper landing or a work area extending to the end of the guides, (e.g. a roof) having a load carrying device (lcd):- which is intended for the transportation of goods only;- where it is forbidden for persons to step upon it at any time;- which is guided;- which is designed to travel at an angle of at least 30 degrees to the vertical but may be used at any angle between the vertical and the maximum inclination as specified by the manufacturer;- which is sustained by

Builders' hoists for goods - Part 2: Inclined hoists with non-accessible load carrying devices

DS/EN 12158-1+A1:2010 用于货物的施工升降机 第1部分：带有可进入平台的升降机

1.1 This standard deals with power operated temporarily installed builders hoists (referred to as """"hoists"""" in this standard) intended for use by persons who are permitted to enter sites of engineering and construction, serving landing levels, having a load carrying device:- designed for the transportation of goods only;- guided;- travelling vertically or along a path within 15 degrees max. of the vertical;- supported or sustained by drum driven wire rope, chain, rack and pinion, hydraulic jack (direct or indirect), or an expanding linkage mechanism;- where masts, when erected, may or may not require support from separate structures;- which permits the

Builders' hoists for goods - Part 1: Hoists with accessible platforms