53.020.99 其他起重设备 标准查询与下载

DIN EN 1495:2009 升降平台.桅杆攀爬工作平台,德文版本 EN 1495:1997+A2:2009

The document specifies the special safety requirements for mast climbing work platforms (MCWP) either permanently or temporarily installed which are manually or power operated and which are used by one or more persons from which to carry out work. Such vertical moving components (work platform) are used to move those same persons and their equipment and materials to and from their working level with persons getting on and off the work platform at one point.

Lifting platforms - Mast climbing work platforms; German version EN 1495:1997+A2:2009

DIN EN 1756-2:2009 尾部提升机.轮式车辆上安装的平台式提升机.安全要求.第2部分:乘客用尾部提升机.德文版本EN 1756-2-2004+A1-2009

This standard specifies safety requirements for the design and testing of platform lifts for mounting on wheeled passenger vehicles, and specifies the safety information that shall be provided for the use of such PLVs. It applies to PLVs: - used for the purpose of embarking and/or disembarking passengers to and from such vehicles; - intended to be fitted, temporarily or permanently, either inside or on the front, side or rear of the wheeled vehicle.

Tail lifts - Platform lifts for mounting on wheeled vehicles - Safety requirements - Part 2: Tail lifts for passengers; German version EN 1756-2:2004+A1:2009

DIN EN 1570:2009 升降台的安全要求,德文版本EN 1570:1998+A2:2009

This document specifies the safety requirements for lifting tables for raising and/or lowering goods and/or persons associated with the movement of goods carried by the lifting table (i.e. not for passenger use), for a vertical travel of up to 3,0 m.

Safety requirements for lifting tables; German version EN 1570:1998+A2:2009

DS/EN 280+A2:2009 移动式升降工作平台 设计计算 稳定性标准 施工 安全 检查和测试

1.1 This European Standard specifies technical safety requirements and measures for all types and sizes of Mobile Elevating Work Platform (MEWP) intended to move persons to working positions where they are carrying out work from the work platform (WP) with the intention that persons are getting on and off the work platform at one defined access position. 1.2 This European Standard is applicable to the structural design calculations and stability criteria, construction, safety examinations and tests before MEWPs are first put into service. It identifies the hazards arising from the use of MEWPs and describes methods for the elimination or reduction of these

Mobile elevating work platforms - Design calculations - Stability criteria - Construction - Safety - Examinations and tests

DS/EN 14010+A1:2009 机械安全 机动车辆动力驱动停车设备 设计、制造、安装和调试阶段的安全和 EMC 要求

1.1 This European Standard deals with the technical requirements to minimise the risks due to the hazards listed in clause 4, which can arise during installation , operation and maintenance of permanently installed equipment and systems for the power driven parking of motor vehicles, as defined in 3.1 to 3.4 below. Requirements are also given on the provision of information for use, which includes requirements for the drafting of the instructions. Electromagnetic compatibility requirements are also covered.1.2 This European Standard applies to equipment and systems for the power driven parking of motor vehicles which have four wheels, are within a maximum s

Safety of machinery - Equipment for power driven parking of motor vehicles - Safety and EMC requirements for design, manufacturing, erection and commissioning stages

DS/EN 1495+A2:2009 升降平台 桅杆爬升工作平台

This standard specifies the special safety requirements for Mast Climbing Work Platforms (MCWP) which are temporarily installed and are manuelly or power operated and which are designed to be used by one or more persons from which to carry out work. The vertical moving components (work platform) are also used to move those same persons and their equipmenet and materials to and from a single boarding point. These restrictions differentiate MCWPs from Builder's hoists.

Lifting platforms - Mast climbing work platforms

NF E52-610/IN2:2009 移动升降工作平台.施工安全检查和试验.稳定性标准设计计算

Mobile elevating work platforms - Design calculations - Stability criteria - Construction - Safety - Examinations and tests.

NF E52-611*NF EN 1495+A2:2009 升降平台.桅杆爬升式作业平台

Lifting platforms - Mast climbing work platforms.

EN 1756-2:2004+A1:2009 尾部升降机.安装在轮式车辆上的平台升降机.安全要求.第2部分:乘客的尾部升降机

Part 2 of standard EN 1756 specifies safety requirements for design of tail lifts as defined in 3.1 for mounting on wheeled passenger vehicles. Vehicles for the loading of disabled passengers onto aircraft and ships are included within the scope of the standard (although dock-mounted lifts are excluded). It also specifies the verification of such tail lifts and the safety information that shall be provided for their use. This document deals with the technical requirements to minimise the hazards listed in clause 4 which can arise during the operation of tail lifts when carried out in accordance with the specifications as intended by the manufacturer or his authorised representative. It applies to passenger tail lifts: used for the purpose of embarking and/or disembarking passengers to and from such vehicles; intended to be fitted, temporarily or permanently, either inside or on the front, side or rear of the wheeled vehicle; driven either by hand or by electric power; equipped with a platform to support passengers who may be pedestrians or riders in wheelchairs and may be accompanied by an attendant. Embarking and/or disembarking operations include the use of a tail lift to lift and/or lower passengers, and if specifically approved by the manufacturer, for use as a link bridge. The standard covers the significant hazards which could occur when a tail lift is used as intended and under the conditions foreseen by the manufacturer. A list of significant hazards is given in clause 4. This document is not applicable to tail lifts which are manufactured before the date of publication of this document by CEN.

Tail lifts - Platform lifts for mounting on wheeled vehicles - Safety requirements - Part 2: Tail lifts for passengers

DIN EN 1494:2009 可移动的起重机和相关提升设备

This European Standard specifies technical safety requirements and measures for mobile or movable jacks (see 3.6) and associated lifting equipment. This European Standard deals with all significant hazards pertinent to mobile or movable jacks and associated lifting equipment when they are used as intended and under the conditions foreseen by the manufacturer. This European Standard specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards. This standard applies to lifting equipment (see 3.1) which are mobile or movable and designed to operate under the load, whether operated singulary or in multiples to partially or totally raise and lower loads or vehicles at one or more lifting points (excluding the lifting of persons) where working under the raised load is not permitted unless additional means of securing the load in position are in place. NOTE Associated lifting equipment means lifting equipment which is similar to those defined in 3.1, but which does not fully comply with these definitions. This standard does not establish additional requirements for -- power drive by an internal combustion machine; -- stability of the mobile or movable jacks and associated lifting equipment; -- operation in severe conditions (e.g. extreme climates, freezer application, strong magnetic fields); -- operation subject to special rules (e.g. potentially explosive atmospheres, mines); -- supply by electrical networks where the tolerances in voltage, frequency etc. differ from those in the public supplies; -- static electric problems; -- handling of loads, the nature of which could lead to dangerous situations (e.g. molten metal, acids, radiating materials, especially brittle loads); -- hazards occurring during producing and decommissioning; -- hazards occurring when using the lifting equipment on public roads; -- wind pressure in and out of use; -- direct contact with foodstuffs; -- operation on sea ships. This standard applies e.g. to the following lifting equipment -- mechanical jacks with or without claw; -- hydraulic jacks with or without claw and with or without integrated pump, e. g. hydraulic trolley jacks, hydraulic transmission jacks, hydraulic pit jacks; -- pneumatic jacks. This standard does not apply to a) jacks or stabilizers which are permanently fixed to a trailer or a container to support a trailer or container without the tractor-unit; b) hydraulic cylinders which are permanently fixed to the vehicle for tipping and/or tilting parts of it; c) support stands with the possibility for changing the lift height only without the load; d) hydraulic lifting equipment working with a maximum pressure exceeding 500 bar and where pump and cylinder are not integrated parts of the same equipment; e) jacks that are delivered with road vehicles for helping when a break-down occurs (including delivery of original spare parts).

Mobile or movable jacks and associated lifting equipment (includes Amendment A1:2008); English version of DIN EN 1494:2009-05

LST EN 1494-2002+A1-2009 移动式或移动式千斤顶及相关起重设备

Mobile or movable jacks and associated lifting equipment

DS/EN 1494+A1:2009 移动式或移动式千斤顶及相关起重设备

This European Standard specifies technical safety requirements and measures for mobile or movable jacks (see 3.6) and associated lifting equipment.This European Standard deals with all significant hazards pertinent to mobile or movable jacks and associated lifting equipment when they are used as intended and under the conditions foreseen by the manufacturer. This European Standard specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards.This standard applies to lifting equipment (see 3.1) which are mobile or movable and designed to operate under the load, whether operated singulary or in multiples to par

Mobile or movable jacks and associated lifting equipment

NF R63-105*NF EN 1494+A1:2009 移动式千斤顶和相关提升设备

Mobile or movable jacks and associated lifting equipment.

JIS C 9620 AMD 1:2009 电动钢丝吊索起重机(修改件1)

Electric wire rope hoists (Amendment 1)

ISO 16653-2:2009 移动式升降工作台.关于特殊部件的设计、计算、安全要求和试验方法.第2部分:带有绝缘部件的移动式升降工作台(MEWPs)

Mobile elevating work platforms - Design, calculations, safety requirements and test methods relative to special features - Part 2: MEWPs with non-conductive (insulating) components

ASME B30.1-2009 千斤顶,工业胶辊,空气脚轮和液压龙门架

This document includes provisions that apply to the construction, operation, inspection, testing, and maintenance of mechanical ratchet jacks, hand- or power-operated mechanical screw jacks, hand- or power-operated hydraulic jacks, air lifting bags, industrial rollers, air casters, and telescopic hydraulic gantry systems. Not included in this document are jacks designed for automotive service, trip-lowered jacks, jacks designed for static support rather than lifting, and jacks, industrial rollers, air lifting bags or air casters that are an integral part of other equipment.

Jacks, Industrial Rollers, Air Casters, and Hydraulic Gantries

ANSI/ASME B30.1-2009 千斤顶,工业滚轴,空气脚轮和液压龙门架

Volume B30.1 includes provisions that apply to the construction, operation, inspection, testing, and maintenance of mechanical ratchet jacks, hand- or power-operated mechanical screw jacks, hand- or power-operated hydraulic jacks, air lifting bags, industrial rollers, air casters, and telescopic hydraulic gantry systems. Not included in this Volume are jacks designed for automotive service, trip-lowered jacks, jacks designed for static support rather than lifting, and jacks, industrial rollers, air lifting bags or air casters that are an integral part of other equipment.

Jacks, Industrial Rollers, Air Casters, and Hydraulic Gantries

ASME PALD-2009 便携式自动提升装置的安全性标准

The scope of this document is the standardization of safety and performance requirements for portable automotive lifting equipment including: (a) hydraulic hand jacks; (b) transmission jacks; (c) engine stands; (d) vehicle support stands; (e) emergency tire changing jacks; (f) upright type mobile lifts; (g) service jacks; (h) wheel dollies; (i) shop cranes; (j) swing type mobile lifts; (k) scissors type mobile lifts; (l) auxiliary stands; (m) automotive ramps; (n) high reach supplementary stands; (o) fork lift jacks; (p) high reach fixed stands; (q) vehicle transport lifts; (r) attachments, adapters, and accessories This Standard may include requirements for safety, health, design, production, construction, maintenance, performance, or operation of equipment, and/or qualification of personnel.

Safety Standard for Portable Automotive Lifting Devices

ANSI/ASME PALD-2009 便携式自动提升装置的安全标准

The scope of this Standard is the standardization of safety and performance requirements for portable automotive lifting equipment including: (a) hydraulic hand jacks(b) transmission jacks(c) engine stands(d) vehicle support stands(e) emergency tire changing jacks(f) upright-type mobile lifts(g) service jacks(h) wheel dollies(i) shop cranes(j) swing-type mobile lifts(k) scissors-type mobile lifts(l) auxiliary stands(m) automotive ramps(n) high reach supplementary stands(o) fork lift jacks(p) high reach fixed stands(q) vehicle transport lifts(r) attachments, adapters, and accessoriesThis Standard may include requirements for safety, health, design, production, construction, maintenance, performance, or operation of equipment, and/or qualification of personnel.

Safety Standard for Portable Automotive Lifting Devices

SANS 1638:2008 气动葫芦

Specifies the characteristics of pneumatically powered chain hoists for vertical lifting involving freely suspended (unguided) loads, and non-vertical lifting and pulling applications.

Pneumatically powered chain hoists