53.020.99 其他起重设备 标准查询与下载

EN 1494:2000+A1:2008 携带或移动式千斤顶及相关的起重设备

This European Standard specifies technical safety requirements and measures for mobile or movable jacks (see 3.6) and associated lifting equipment. This European Standard deals with all significant hazards pertinent to mobile or movable jacks and associated lifting equipment when they are used as intended and under the conditions foreseen by the manufacturer. This European Standard specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards. This standard applies to lifting equipment (see 3.1) which are mobile or movable and designed to operate under the load, whether operated singulary or in multiples to partially or totally raise and lower loads or vehicles at one or more lifting points (excluding the lifting of persons) where working under the raised load is not permitted unless additional means of securing the load in position are in place. NOTE Associated lifting equipment means lifting equipment which is similar to those defined in 3.1, but which does not fully comply with these definitions. This standard does not establish additional requirements for power drive by an internal combustion machine; stability of the mobile or movable jacks and associated lifting equipment; operation in severe conditions (e. g. extreme climates, freezer application, strong magnetic fields); operation subject to special rules (e. g. potentially explosive atmospheres, mines); supply by electrical networks where the tolerances in voltage, frequency etc. differ from those in the public supplies; static electric problems; handling of loads, the nature of which could lead to dangerous situations (e. g. molten metal, acids, radiating materials, especially brittle loads); hazards occurring during producing and decommissioning; hazards occurring when using the lifting equipment on public roads; wind pressure in and out of use; direct contact with foodstuffs; operation on sea ships. This standard applies e. g. to the following lifting equipment mechanical jacks with or without claw; hydraulic jacks with or without claw and with or without integrated pump, e. g. hydraulic trolley jacks, hydraulic transmission jacks, hydraulic pit jacks; pneumatic jacks. This standard does not apply to a) jacks or stabilizers which are permanently fixed to a trailer or a container to support a trailer or container without the tractor-unit; b) hydraulic cylinders which are permanently fixed to the vehicle for tipping and/or tilting parts of it; c) support stands with the possibility for changing the lift height only without the load; d) hydraulic lifting equipment working with a maximum pressure exceeding 500 bar and where pump and cylinder are not integrated parts of the same equipment; e) jacks that are delivered with road vehicles for helping when a break-down occurs (including delivery of original spare parts).

Mobile or movable jacks and associated lifting equipment

DIN EN 1756-1:2008 尾部升降机.带轮车辆上安装的平台式升降机.安全要求.第1部分:货物用尾部升降机

This European Standard specifies safety requirements for design of tail lifts as defined in 3.1 for mounting on wheeled goods vehicles. It also specifies the verification of such tail lifts and the safety information that shall be provided for their use. This European Standard deals with the technical requirements to minimize the hazards listed in clause 4 which can arise during the operation of tail lifts when carried out in accordance with the specifications as intended by the manufacturer or his authorized representative. It applies to tail lifts : -- used for the purpose of loading and/or unloading such vehicles ; -- intended to be fitted, temporarily or permanently, either inside or on the front, side or rear of the wheeled vehicle ; -- driven either by hand or electric powered ; -- equipped with a platform to support loads which comprise goods, an operator, or a combination of the two ; -- with a maximum lifting height not exceeding 3 m above ground, the measurement shall be made when the platform is unloaded ; -- rotary type with a maximum lifting height not exceeding 2 m ; -- used as a link bridge when intended by the manufacturer. NOTE A tail lift should not be confused with a link bridge attached to a loading dock which is included within the definition of a dock leveller and is outside the scope of this standard. Loading and/or unloading operations include the use of a tail lift to lift and/or lower loads This European Standard does not establish the additional requirements for : -- operation in severe conditions (e.g. extreme environmental conditions such as freezer applications, high temperatures, corrosive environment, tropical environment, contaminating environments, strong magnetic fields) ; -- operations subject to special rules (e.g. potentially explosive atmospheres) ; -- supply by electrical networks and the electrical circuit ; -- power take off part of the system ; -- cable less remote control and electronic equipment ; -- electromagnetic compatibility (emission-immunity) ; -- static electricity problems ; -- handling of loads the nature of which could lead to dangerous situations (e.g. molten metal, acids/bases, radiating materials, specially brittle loads) ; -- hazards occurring during installation, transportation, decommissioning ; -- hazards occurring when handling suspended loads which may swing freely ; -- requirement related to the use on public roads ; -- wind pressure in and out of use ; -- direct contact with foodstuffs ; -- earthquake ; -- lightning.

Tail lifts - Platform lifts for mounting on wheeled vehicles - Safety requirements - Part 1: Tail lifts for goods(includes Amendment A1:2008); English version of DIN EN 1756-1:2008-10

BS ISO 16653-1:2008 移动式升降工作平台.关于特殊部件的设计、计算、安全要求和试验方法.带有伸缩式护栏设备的移动式升降工作平台(MEWPs)

Mobile elevating work platforms - Design, calculations, safety requirements and test methods relative to special features - MEWPs with retractable guardrail systems

LST EN 1756-1-2002+A1-2008 尾板升降机 安装在轮式车辆上的平台升降机 安全要求 第1部分：货物尾板升降机

Tail lifts - Platform lifts for mounting on wheeled vehicles - Safety requirements - Part 1: Tail lifts for goods

ISO 16653-1:2008 移动式升降工作台.关于特殊部件的设计、计算、安全要求和试验方法.第1部分:带有伸缩式护栏设备的移动式升降工作台(MEWPs)

Mobile elevating work platforms - Design, calculations, safety requirements and test methods relative to special features - Part 1: MEWPs with retractable guardrail systems

SANS 1639:2008 翻新气动葫芦

Specifies requirements for reconditioned pneumatically operated chain hoists. Reconditioning procedures are also covered.

Reconditioned pneumatically operated chain hoists

SANS 1637:2008 翻新手扳葫芦

Specifies requirements for reconditioned manually operated chain lever hoists. Reconditioning procedures are also covered.

Reconditioned manually operated chain lever hoists

NF R18-905-1/IN1:2008 后置升降机.安装在轮式车辆上的平台式升降机.安全要求.第1部分:货运用后置升降机

Tail lifts - Platform lifts for mounting on wheeled vehicles - Safety requirements - Part 1 : tail lifts for goods.

NF R18-905-1:2008 后置升降机.安装在轮式车辆上的平台式升降机.第1部分:货运用后置升降机

Tail lifts - Platform lifts for mounting on wheeled vehicles - Safety requirements - Part 1 : tail lifts for goods.

EN 1756-1:2001+A1:2008 尾部升降机.安装在轮式车辆上的平台升降机.安全要求.第1部分:货物的尾部升降机

This European Standard specifies safety requirements for design of tail lifts as defined in 3.1 for mounting on wheeled goods vehicles. It also specifies the verification of such tail lifts and the safety information that shall be provided for their use. This European Standard deals with the technical requirements to minimize the hazards listed in clause 4 which can arise during the operation of tail lifts when carried out in accordance with the specifications as intended by the manufacturer or his authorized representative. It applies to tail lifts: used for the purpose of loading and/or unloading such vehicles; intended to be fitted, temporarily or permanently, either inside or on the front, side or rear of the wheeled vehicle; driven either by hand or electric powered; equipped with a platform to support loads which comprise goods, an operator, or a combination of the two; with a maximum lifting height not exceeding 3 m above ground, the measurement shall be made when the platform is unloaded; rotary type with a maximum lifting height not exceeding 2 m; used as a link bridge when intended by the manufacturer. NOTE A tail lift should not be confused with a link bridge attached to a loading dock which is included within the definition of a dock leveller and is outside the scope of this standard. Loading and/or unloading operations include the use of a tail lift to lift and/or lower loads This European Standard does not establish the additional requirements for: operation in severe conditions (e. g. extreme environmental conditions such as freezer applications, high temperatures, corrosive environment, tropical environment, contaminating environments, strong magnetic fields); operations subject to special rules (e. g. potentially explosive atmospheres); supply by electrical networks and the electrical circuit; power take off part of the system; cable less remote control and electronic equipment; electromagnetic compatibility (emission-immunity); static electricity problems; handling of loads the nature of which could lead to dangerous situations (e. g. molten metal, acids/bases, radiating materials, specially brittle loads); hazards occurring during installation, transportation, decommissioning; hazards occurring when handling suspended loads which may swing freely; requirement related to the use on public roads; wind pressure in and out of use; direct contact with foodstuffs; earthquake; lightning.

Tail lifts - Platform lifts for mounting on wheeled vehicles - Safety requirements - Part 1: Tail lifts for goods

GOST R 53037-2008 移动升降工作台.设计计算,安全性要求,试验

Mobile elevating work platforms. Design calculations, safety requirements, tests

SANS 7752-1:2007 起重机械．控制装置．布置形式和特性．第1部分：一般原则

Establishes principles and requirements for the controls of lifting appliances. Deals with the arrangement of those controls which are used in positioning loads and serves as general basis for the elaboration of detailed standards covering controls for p

Lifting appliances - Controls - Layout and characteristics Part 1: General principles

SANS 1636:2007 手动链式杠杆起重机

Specifies the requirements for manually operated chain lever hoists.

Manually operated chain lever hoists

ISO 16369:2007 升降工作平台.桅杆爬升式工作平台

This International Standard specifies particular safety requirements for mast-climbing work platforms (MCWP) which are temporarily installed and are manually or power-operated, and which are designed to be used by one or more persons from which to carry out work. NOTE The vertical-moving components (work platforms) are also used to move those same persons and their equipment and materials to and from a single boarding point. These restrictions differentiate MCWP from builder’s hoists. This International Standard is also applicable to permanently installed MCWP. This International Standard is applicable to work platforms which are elevated by a drive system and guided by and moved along their supporting masts, where the masts may or may not require lateral restraint from separate supporting structures. This International Standard is applicable to any combination of the following alternatives: -- one or more masts; -- mast tied or untied; -- mast of fixed or variable length; -- masts vertical or inclined between 0° and 30° to the vertical; -- masts which are standing or hanging; -- movable or static base (chassis or base frame); -- manual or power-operated elevation; -- towed or self-powered ground travel on site, excluding road traffic regulation requirements; -- driven using electric, pneumatic, hydraulic motors or internal combustion engines. This International Standard identifies the hazards arising during the various phases in the life of such equipment and describes methods for the elimination or reduction of these hazards and for the use of safe working practices. This International Standard does not specify the requirements for dealing with the hazards involved in the manoeuvring, erection or dismantling, fixing or removing of any materials or equipment which are not part of the MCWP, nor does it deal with the handling of specific hazardous materials. This International Standard does not specify the requirements for delivering persons and materials to fixed landing levels. Such equipment is referred to as lifts or hoists and is dealt with by other International Standards. This International Standard does not apply to mobile elevating work platforms (MEWPs) in accordance with ISO 16368, suspended access equipment in accordance with EN 1808 or lifting tables in accordance with EN 1570.

Elevating work platforms - Mast-climbing work platforms

JB/T 7332-2007 手动单轨小车

本标准规定了手动单轨小车的型式和基本参数、技术要求、试验方法、检验规则以及标志和包装。 本标准适用于额定载重量为0.25t～40t、以手拉链条驱动及额定载重量为0.25t～10t、以手推起吊重物驱动，运行于工字钢轨道下翼缘上的手动单轨小车（以下简称单轨小车）。

Manual trolleys

JB/T 7334-2007 手拉葫芦

本标准规定了手拉葫芦的工作级别、基本参数、技术要求、试验方法、检验规则以及标志和包装。 本标准适用于一般用途的渐开线直齿圆柱齿轮传动的手拉葫芦，其他结构型式的手拉葫芦可参照使 用。

Chain hoists

JB/T 5317-2007 环链电动葫芦

本标准规定了环链电动葫芦（以下简称环链葫芦）的型式与基本参数、技术要求、试验方法、检验规则、标志、包装和质量保证期等内容。 本标准适用于一般用途的环链葫芦，特殊用途的环链葫芦可参照使用。

Electric chain hoists

JB/T 7335-2007 环链手扳葫芦

本标准规定了环链手扳葫芦的基本参数、技术要求、试验方法、检验规则以及标志和包装。 本标准适用于一般用途的渐开线圆柱齿轮传动的环链手扳葫芦（以下简称手扳葫芦），其他结构型式的环链手扳葫芦可参照使用。

Lever hoists

ASME B30.25-2007 废料和物料装卸搬运设备

This standard applies to the construction, installation, operation, inspection, and maintenance of scrap handlers consisting of a base, a revolving upper structure with operator's station(s), and a front for lifting scrap or materials using attachments such as magnets and grapples, and any variations thereof in which the equipment retains the same fundamental characteristics. The provisions included in this standard apply to scrap handlers that are crawler mounted, rail mounted, wheel mounted, or on pedestal bases. The scope includes only handlers used to lift, lower, and swing scrap and material at various radii, which are powered by internal combustion engines or electric motors, and which are operated hydraulically. Hydraulic excavators designed for digging and trenching, forestry machines, machines designed for demolition, lattice and telescopic boom cranes, rail-mounted cranes for railway and automobile wreck clearance, and equipment covered by other B30 standards are excluded.

Scrap and Material Handlers Safety Standard for Cableways, Cranes, Derricks, Hoists, Hooks, Jacks, and Slings

SANS 16368:2007 移动式升降工作台.设计计算、安全要求和试验方法

Specifies technical safety requirements and measures for all types and sizes of mobile elevating work platforms (MEWPs) intended to move persons to working positions. Applicable to the structural design calculations and stability criteria, construction, safety examinations and security tests before MEWPs are put into service. Identifies the hazards arising from the use of MEWPs and describes methods for the elimination or reduction of these hazards.

Mobile elevating work platforms - Design calculations, safety requirements and test methods