53.020.99 其他起重设备 标准查询与下载

SANS 18893:2007 移动式升降工作平台．安全原则，检验，维护和运行

Applies to all Mobile Elevating Work Platforms (MEWPs) that are intended to position persons, tools and materials and which consists, at least, of a work platform with controls, an extending structure and a chassis. The technical safety requirements sha

Mobile elevating work platforms - Safety principles, inspection, maintenance and operation

CAN/CSA-B354.5-2007(C2016) 工作平台沿桅杆移动

1 Domaine d'application 1.1 Généralités Cette norme vise les plates-formes de travail se déplaçant le long de mâts (PTDM) qui servent surtout de surfaces de travail en hauteur pour les travailleurs, avec leurs outils et matériaux. Une PTDM comprend généralement les caractéristiques suivantes (voir les figures 1 et 2) : a) une ou plusieurs plates-formes de travail ; b) un ou plusieurs mâts qui sont : (i) autostables ou supportés latéralement au-dessus de leur bases ; (ii) fixes ou de longueur variable ; (iii) verticaux ou inclinés entre 0° et 30° par rapport à la verticale ; et (iv) supportés verticalement uniquement à l'extrémité supérieure ou à l'extrémité inférieure ; c) un châssis fixe ou qui peut se déplacer horizontalement par autopropulsion ou remorquage ; et d) un mécanisme d'élévation manuel ou motorisé. La vitesse de montée ou de descente ne doit pas être supérieure à 0,20 m/s (0,8 pi/s). 1.2 Objet Cette norme vise à établir les exigences minimales visant la conception, la fabrication, la reprise, la remise en état ou à neuf, la mise à l'essai, le rendement, l'inspection, la formation, l'entretien et la conduite prudente des PTDM afin de : a) prévenir les blessures corporelles et les accidents ; b) uniformiser les caractéristiques nominales ; et c) définir les responsabilités respectives des constructeurs, des concessionnaires, du personnel d'entretien, des opérateurs, des propriétaires et des utilisateurs. Les PTDM sont généralement conçues pour utilisation sur une surface de niveau. Elles ne sont normalement pas isolées pour utilisation à proximité de circuits électriques sous tension ni conçues pour utilisation dans des emplacements dangereux. La CAN/CSA-C225 traite des plates-formes élévatrices conçues pour utilisation à proximité de circuits électriques sous tension. La conduite de PTDM présente certains risques et c'est la raison pour laquelle on doit faire appel à du personnel compétent et attentif, ayant reçu la formation appropriée portant sur l'utilisation prévue, la conduite prudente, l'entretien et la réparation de PTDM. 1.3 Application Les exigences de conception et de fabrication de cette norme s'appliquent aux PTDM construites après la date de publication de cette norme. 1.4 Matériel non visé Cette norme ne vise pas : a) les engins élévateurs à nacelle portés sur véhicule visés par la CAN/CSA-C225 ; b) les plates-formes élévatrices mobiles visées par la CAN/CSA-B354.1 ; c) les plates-formes de travail élévatrices automotrices visées par la CAN/CSA-B354.2 ; d) les plates-formes de travail élévatrices automotrices à bras articulé visées par la CAN/CSA-B354.4 ; e) les monte-charges de chantier utilisés pour transporter verticalement les matériaux et le personnel, visés par la CAN/CSA-Z185 et la CAN/CSA-Z256 ; f) les grues mobiles visées par la CAN/CSA-Z150 ; g) les engins à déplacement vertical portés sur véhicule visés par l'ANSI/SIA A92.7 ; h) les engins d'inspection et d'entretien des ponts portés sur véhicule visés par l'ANSI/SIA A92.8 ; i) les élévateurs installés à demeure (fixes) utilisés pour transporter le personnel entre différentes hauteurs ; et j) le matériel de lutte contre les incendies. 1.5 Terminologie Dans les normes CSA, le terme «doit» indique une exigence, c'est-à-dire une prescription que l'utilisateur doit respecter pour assurer la conformité à la norme ; «devrait» indique une recommandation ou ce qu'il est conseillé mais non obligatoire de faire ; et «peut», une possibilité ou un conseil. Les notes qui accompagnent les articles ne comprennent pas de prescriptions ni de recommandations. Elles servent à séparer du texte les explications ou les renseignements qui ne font pas proprement partie de la norme. Les notes au bas des figures et des tableaux font partie de ceux-ci et peuvent être rédigées comme des prescriptions. Les annexes peuvent être normatives (obligatoires) ou informatives (facultatives).

Work platforms moving along masts

SANS 7752-2:2007 起重机械．控制装置．布置形式和特性．第2部分：流动式起重机的基本布置和要求

Establishes the arrangement, requirements, and direction of movement of the basic controls for slewing, load hoisting and lowering and jib luffing and telescoping. Applies to all mobile cranes as defined in IS0 4306-2.

Lifting appliances - Controls - Layout and characteristics Part 2: Basic arrangement and requirements for mobile cranes

ANSI A10.4-2007 修建和拆除场地的载人升降机用安全要求

This standard applies to the design, construction, installation, operation, inspection, testing, maintenance, alterations and repair of hoists and elevators that (1) are not an integral part of buildings, (2) are installed inside or outside buildings or

Safety Requirements for Personnel Hoists on Construction and Demolition Sites

CAN/CSA-B354.5-2007(R2016) 桅杆攀爬工作平台

1 Scope 1.1 General This Standard applies to mast-climbing work platforms (MCWPs) that are primarily used to provide a working surface for personnel, along with their necessary tools and materials, at elevated work locations. An MCWP typically includes the following features (see Figures 1 and 2): (a) one or more work platforms; (b) one or more masts that are (i) free-standing or laterally supported above their bases; (ii) of fixed or variable height; (iii) vertical or inclined between 0 and 30° to the vertical; and (iv) vertically supported only at their bottom or top; (c) a chassis that is static or capable of transfer at a work site by self-propulsion or towing; and (d) an elevating mechanism that is manually or power operated. Raising and lowering speeds are limited to a maximum of 0.20 m/s (0.8 ft/s). 1.2 Purpose The purpose of this Standard is to specify minimum design, manufacturing, remanufacturing, rebuilding/reconditioning, testing, performance, inspection, training, maintenance, and safe operation requirements for MCWPs to achieve the following objectives: (a) prevention of personal injuries and accidents; (b) uniformity in ratings; and (c) understanding by manufacturers, dealers, installers, maintenance personnel, operators, owners, and users of their respective responsibilities. MCWPs are generally intended for use over level surfaces. Normally, they are not insulated for use near electrically energized circuits, nor are they intended to be used in hazardous locations. For aerial platforms intended for use near electrically energized circuits, see CAN/CSA-C225. The operation of MCWPs is subject to certain hazards and therefore needs to be performed by competent, careful personnel trained in the intended use, safe operation, maintenance, and servicing of MCWPs. 1.3 Application The design and manufacturing requirements of this Standard apply to MCWPs manufactured after the date of publication of this Standard. 1.4 Equipment not covered This Standard does not apply to (a) vehicle-mounted aerial devices covered by CAN/CSA-C225; (b) non-self-propelled elevating rolling work platforms covered by CAN/CSA-B354.1; (c) self-propelled elevating work platforms covered by CAN/CSA-B354.2; (d) self-propelled boom-supported elevating work platforms covered by CAN/CSA-B354.4; (e) construction hoists used to raise and lower materials and personnel covered by CAN/CSA-Z185 and CAN/CSA-Z256; (f) mobile cranes covered by CAN/CSA-Z150; (g) vehicle-mounted vertical lift devices covered by ANSI/SIA A92.7; (h) vehicle-mounted bridge inspection and maintenance devices covered by ANSI/SIA A92.8; (i) permanently installed (non-mobile) elevating lifts used to transport personnel between different elevations; and (j) firefighting equipment.

Mast-Climbing Work Platforms

SANS 1903:2007 安全要求．悬吊式人孔道安全要求．计算，稳定性，建筑检验

Specifies additional and modified safety requirements for suspended access equipment. Is applicable to both permanent and temporary equipment, which may be powered or hand operated.

Safety requirements on suspended access equipment - Design calculations, stability criteria, construction - Tests

DB42/ 365-2006 钢丝绳或货用施工升降机安全技术规范

safety technology acceptance of rope suspended material hoist

ANSI/SIA A92.6-2006 自推进式升降工作平台

This standard applies to self-propelled integral chassis aerial platforms having a platform that cannot be positioned completely beyond the base and are used to position personnel, along with their necessary tools and materials, at work locations. Aerial platforms are power operated with primary functions including drive controlled from the platform.

Self-Propelled Elevating Work Platforms

LST EN 61057-2001/AC-2006 用于超过 1 kV ac 工作的带有绝缘吊杆的高空作业设备（IEC 61057:1991，已修改）

Aerial devices with insulating boom used for working exceeding 1 kV a.c. (IEC 61057:1991, modified)

NF R18-905-2:2006 尾部升降机.安装在轮式车辆上的平台式升降机.安全要求.第2部分:客运尾部升降机

Tail lifts - Platform lifts for mounting on wheeled vehicles - Safety requirements - Part 2 : tail lifts for passengers.

DLA MIL-DTL-13220 D-2006 (和钢缆一起使用的)捆木索滑行钩

This specification covers cast steel or drop forged sliding choker hooks for use with wire rope plain end loop and thimbled slings.

HOOKS, SLIDING CHOKER (FOR USE WITH WIRE ROPE)

ANSI/SIA A92.5-2006 吊臂式升降工作平台

Applies to self-propelled integral chassis aerial platforms having a platform that can be positioned completely beyond the base and are used to position personnel, along with their necessary tools and materials, at work locations. Aerial platforms are power operated with primary functions, including drive, controlled from the platform. Such aerial platforms are intended to be occupied when driven.

Boom-Supported Elevating Work Platforms

ANSI/ASME B30.20-2006 下吊钩提升装置

B30.20 includes provisions that apply to the marking, construction, installation, inspection, testing, maintenance, and operation of below-the-hook lifting devices, other than slings, used for attaching loads to hoists, including: Structural and Mechanical Devices; Vacuum Lifting Devices; Close Proximity Operated Lifting Magnets; Remotely Operated Lifting Magnets; and Scrap and Material Handling Grapples

Below-the-Hook Lifting Devices

ASME B30.20-2006 下吊钩提升装置

Volume B30.20 includes provisions that apply to the marking, construction, installation, inspection, testing, maintenance, and operation of below-the-hook lifting devices, other than slings, used for attaching loads to hoist. The devices are arranged in four chapters as follows: Chapter 20-1: Structural and Mechanical Lifting Devices. Chapter 20-2: Vacuum Lifting Devices. Chapter 20-3: Operated Close Proximity Lifting Magnets. Chapter 20-4: Remotely Operated Lifting Magnets.

Below-the-Hook Lifting Devices

BS 8460:2005 MEWPs的安全使用.实施规范

This British Standard gives guidance and recommendations for persons responsible for the selection, hiring, positioning, maintenance and thorough examination of mobile elevating work platforms (MEWPs). It also gives guidance and recommendations for the safe use of MEWPs, including the selection and training of operators and other personnel, together with guidance to assist in the selection of competent persons. NOTE 1 This British Standard does not give recommendations for delivering persons and materials to fixed landing levels. Equipment intended for this purpose, such as lifts or hoists, are dealt with by other standards including BS EN 12158-1, Builder’s hoists for goods, BS EN 12159, Builder’s hoists for goods and passengers and BS EN 81, Safety rules for the construction and installation of lifts. NOTE 2 Mast climbing work platforms (MCWPs) conforming to BS EN 1498, suspended access equipment defined in accordance with BS EN 1808, lifting tables defined in accordance with BS EN 1570, fire fighting and fire rescue appliances defined in accordance with BS EN 1777, and non-integrated working platforms on forklift trucks are not included within the scope of this British Standard.

Safe use of MEWPs - Code of practice

ASME B30.21-2005 手动操作杆式提升机

This Standard applies to the construction, installation, operation, inspection, maintenance, and safe use of lifting equipment used in construction and industrial settings. This includes, but is not limited to: articulatingboom, container, gantry, mobile, pedestal, portal, tower and stacker cranes; balance-lifting units; below-the-hook lifting devices; cableways; derricks; jacks; hoists; hooks; loads suspended from rotorcraft; material placement systems; monorails; rigging hardware; and scrap and material handlers.

Manually Lever Operated Hoists

DLA A-A-52464 B VALID NOTICE 1-2005 环型牵引车钩:60000磅车全重轻载抵销60000磅车全重(锥柄)和120000磅车全重重载

A-A-52464B, dated 7 September 1999, has been reviewed and determined to be valid for use in acquisition

COUPLER, DRAWBAR, RING: LIGHT DUTY, 60,000 LB GVW; OFFSET (TAPER SHANK), 60,000 LB GVW; AND HEAVY DUTY 120,000 LB GVW

ANSI/ASME B30.21-2005 手动杠杆操作提升机

B30.21 includes provisions which apply to the construction, installation, operation, inspection, and maintenance of ratchet and pawl and friction brake type manually lever operated chain, wire rope, and web strap hoists used for lifting, pulling, and tensioning applications.

Manually Lever Operated Hoists

ASME PALD-2005 便携式自动提升装置安全标准

PALD aplies to the design, testing, operation, maintenance, and inspection of portable automotive lifting devices including: hydraulic hand jacks, transmission jacks, engine stands, vehicle support stands, emergency tire changing jacks, upright-type mobile lifts, service jacks, wheel dollies, shop cranes, swing-type mobile lifts, scissors-type mobile lifts, auxiliary stands, automotive ramps, high reach supplementary stands, fork lift jacks, high reach fixed stands, vehicle transport lifts, and attachments, adapters, and accessories.

Safety Standard for Portable Automotive Lifting Devices

ISO 18893:2004 移动式升降工作平台.安全原则、检验、维护和运行

This International Standard applies to all Mobile Elevating Work Platforms (MEWPs) that are intended to position persons, tools and materials and which, as a minimum, consists of a work platform with controls, an extending structure and a chassis. The technical safety requirements of this International Standard shall apply except where national or local regulations are more stringent. For related information, see ISO 16368. This International Standard applies to MEWPs to achieve the following objectives: a) prevention of personal injuries, property damage and accidents; b) establishment of criteria for inspection, maintenance and operation.

Mobile elevating work platforms - Safety principles, inspection, maintenance and operation