共找到 744 条与 瓶、小罐、瓮 相关的标准,共 50 页
The project specifies finishes for lever being preferably developed for glass packaging with a cliplock concerning DIN 5097.
Means of packaging - Finishes - Part 3: Finish for lever stoppers
Glass jars canned food. Basic parameters and dimensions
Glass jars for canned food. General specifications
This standard specifies a gravimetric method for determining the brimful and total capacities of plastic bottles and jars up to 5 litres, of plastic canisters/jerricans with a nominal volume up to 20 litres and of plastic pails with a nominal volume up to 60 litres.
Rigid plastics containers - Definition of nominal, brimful and total capacity and measurement of brimful and total capacity
This standard specifies tolerances for dimensions, mass and volume of plastic bottles and jars with a nominal capacity up to 5 litres, of plastics canisters/jerricans with a nominal volume op to 20 litres and for plastic pails up to 60 litres.
Rigid plastics containers - Specification of tolerance for dimensions, weight and volume
This standard specifies a method for determination on the drainability of plastic bottles and jars with a nominal capacity up to 5 litres and of plastics canisters/jerricans with a nominal volume up to 20 litres.
Rigid plastics containers - Method for determination of drainability
Glass container-Height and non-parallelism of finish with reference to container base-Test methods
Glass container-Height and non-parallelism of finish with reference to container base-Test methods
이 규격은 유리 용기의 높이 및 수직도를 측정하기 위한 시험 방법을 명시한다.
Glass container-Height and non-parallelism of finish with reference to container base-Test methods
Glass containers - Height and non-parallelism of finish with reference to container base - Test methods (ISO 9009:1991)
Glass bottles - Verticality - Test method (ISO 9008:1991)
Chemical product labeling is required by the OSHA Hazard Communications Standard 29 CFR 1910.1200. ANSI Standard Z129.1 establishes specific guidelines for preparation of labeling consistent with the OSHA Standard. This guide is intended as an interpretation of these standards as they apply to these specific products and grades. This guide is intended to provide suggestions for the minimum required labeling for these chlorinated solvents. It is not intended to replace labeling determinations made by manufacturers or packagers. This guide applies to commercially available grades of these specific products. For solvent blends, or formulations with other materials, consult ANSI Z129.1.1.1 This guide is intended to provide industrial health and safety labeling for the following chlorinated hydrocarbon solvents: methylene chloride, perchloroethylene, and trichloroethylene. Additional labeling may be required if other chemicals are mixed with these solvents, or if special containers (for example, aerosol packages) are employed.
Standard Guide for Labeling Chlorinated Hydrocarbon Solvent Containers
Packages for certain prepacked foodstuffs - Capacities of glass and metal containers
Packaging - Cork mouth finish with a bore diameter of 18,5 mm for corks and tamper evident capsules
Method of measurement of glass thickness forcarbonated beverage bottles
Testing method for strain of carbonated beverage bottles
이 규격은 탄산 음료용 유리병의 두께 측정 방법에 대하여 규정한다.
Method of measurement of glass thickness forcarbonated beverage bottles
Method of measurement of glass thickness forcarbonated beverage bottles
이 규격은 탄산 음료용 유리병의 스트레인 시험 방법에 대하여 규정한다.
Testing method for strain of carbonated beverage bottles
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号