59.100.10 纺织玻璃纤维材料 标准查询与下载
共找到 578 条与 纺织玻璃纤维材料 相关的标准，共 39 页
This International Standard provides a basis for a specification applicable to textured yarns made from single or folded yarns of textile glass. Textured glass yarns can be produced by several types of process. They can be made starting either from a single strand or from two or more strands in which one or more have been “opened” to give the “bulky” aspect of textured yarn. Textured glass yarn is used in various applications, for example insulation, filtration, the manufacture of decorative textiles, the reinforcement of plastics and the manufacture of packing materials.
Textile glass - Textured yarns - Basis for a specification
- ICS
- 59.100.10
- CCS
- Q36
- 发布
- 2011-02-15
- 实施
- 2011-02-15
1 Scope This International Standard specifies a method for determining the twist balance index of folded yarn and cabled yarn made from textile glass, carbon, aramid or any other reinforcement fibre.
Reinforcement yarns. Determination of twist balance index
- ICS
- 59.100.10
- CCS
- 发布
- 2011-01-31
- 实施
- 2011-01-31
General specification for stitch-bonded fiberglass unidirectional fabric
- ICS
- 59.100.10
- CCS
- Q36
- 发布
- 2011-01-04
- 实施
- 2011-02-01
5.1 The damage-based design approach will permit an additional method of design for GFRP materials. This is a very useful technique to determine the performance of different types of resins and composition of GFRP materials in order to develop a damage tolerant and reliable design. This AE-based method is not unique, other damage-sensitive evaluation methods can also be used. 5.2 This practice involves the use of acoustic emission instrumentation and examination techniques as a means of damage detection to support a destructive test, in order to derive the damage-based design stress. 5.3 This practice is not intended as a definitive predictor of long-term performance of GFRP materials (such as those used in vessels). For this reason, codes and standards require cyclic proof testing of prototypes (for example, vessels) which are not a part of this practice. 5.4 Other design methods exist and are permitted. 1.1 This practice details procedures for establishing the direct stress and shear stress damage-based design values for use in the damage-based design criterion for materials to be used in GFRP vessels and other GFRP structures. The practice uses data derived from acoustic emission examination of four-point beam bending tests and in-plane shear tests (see ASME Section X, Article RT-8). 1.2 The onset of lamina damage is indicated by the presence of significant acoustic emission during the reload portion of load/reload cycles. “Significant emission” is defined with historic index. 1.3 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units which are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Standard Practice for Determining Damage-Based Design Stress for Glass Fiber Reinforced Plastic (GFRP) Materials Using Acoustic Emission
- ICS
- 59.100.10
- CCS
- 发布
- 2011
- 实施
Textile glass chopped-strand mats for reinforcement of plastics. Determination of time of dissolution of the binder in styrene
- ICS
- 59.100.10
- CCS
- Q36
- 发布
- 2010-12-31
- 实施
- 2010-12-31
This International Standard specifies a method for determining the twist balance index of folded yarn and cabled yarn made from textile glass, carbon, aramid or any other reinforcement fibre.
Reinforcement yarns - Determination of twist balance index
- ICS
- 59.100.10
- CCS
- W59
- 发布
- 2010-12-15
- 实施
- 2010-12-15
Textile glass — Woven fabrics — Determination of thickness AMENDMENT 1
Textile glass - Woven fabrics - Determination of thickness; Amendment 1
- ICS
- 59.100.10
- CCS
- Q36
- 发布
- 2010-12-15
- 实施
- 2010-12-15
This International Standard specifies a method of determining the time taken for a tensile load to break the bond between the strands of a textile glass chopped-strand mat, used for the reinforcement of plastics, which is immersed in styrene.
Textile glass chopped-strand mats for reinforcement of plastics - Determination of time of dissolution of the binder in styrene
- ICS
- 59.100.10
- CCS
- Q23
- 发布
- 2010-10
- 实施
이 표준은 플라스틱의 강화에 사용하는 유리 로빙(이하 로빙이라 한다.)에 대하여 규정한다.
Glass roving
- ICS
- 59.100.10
- CCS
- Q37
- 发布
- 2010-07-27
- 实施
- 2010-07-27
Textile glass - Determination of stiffness of rovings
- ICS
- 59.100.10
- CCS
- W50
- 发布
- 2010-01-31
- 实施
- 2010-01-31
1 Scope This International Standard specifies a method for the determination of the stiffness of textile glass rovings.
Textile glass. Determination of stiffness of rovings
- ICS
- 59.100.10
- CCS
- 发布
- 2010-01-31
- 实施
- 2010-01-31
1.1 This specification primarily covers greige tapes and webbings woven from “E” electrical classification glass fiber yarns. This specification can also be applied to tapes and webbings made of other glass fiber grades upon agreement between the purchaser and the supplier. 1.2 This specification is intended to assist ultimate users by designating the types of these products that are typical in the industry. This specification permits the application of organic materials to the glass fiber yarn during manufacture that helps facilitate weaving. When used as permitted in this specification, such materials will not interfere with the intended end use requirements. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Standard Specification for Greige Woven Glass Tapes and Webbings
- ICS
- 59.100.10
- CCS
- W59
- 发布
- 2010
- 实施
1.1 This specification covers finished fabrics woven from “E” electrical glass fiber yarns that are intended as a reinforcing material in laminated plastics for structural use. This specification can also be applied to fabrics made of other glass types as agreed upon between the purchaser and the supplier. 1.2 This specification specifies the terminology, definitions, general requirements, and physical requirements for finished woven glass fabrics This specification permits the application of sizing materials to the glass fiber yarn during manufacture that helps facilitate weaving. These organic materials are typically removed from the greige fabric and replaced with a finish that is compatible with the resin matrix specified in the contracting document Note 18212;Sizing materials on glass fiber yarns, in most cases, are removed by various cleaning procedures as a first stage in preparing a finished fabric. When these yarn sizing materials are removed during a cleaning procedure they need not be compatible with the subsequent resin matrix. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 This specification is one of a series to provide a substitute for Military Specifications: MIL-Y-1140 Yarn, Cord, Sleeving, Cloth, and Tape-Glass; and MIL-C-9084 Cloth, Glass Finished for Resin Laminates. 1.5 Additional ASTM specifications in this series have been drafted and appear in current editions of the Annual Book of ASTM Standards. These include greige glass fabrics, glass tapes, glass sleevings, glass cords, glass sewing threads, and finished laminates made from finished glass fabrics. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Standard Specification for Finished Woven Glass Fabrics
- ICS
- 59.100.10
- CCS
- Q36
- 发布
- 2010
- 实施
This method covers the determination of the tensile strength and elongation at break of fiber glass mats.
Tensile strength and elongation at break for fiber glass mats
- ICS
- 59.100.10
- CCS
- Q36
- 发布
- 2010
- 实施
This test method covers the determination of the moisture sensitivity of fiber glass mat binder systems.
Moisture sensitivity of fiber glass mats
- ICS
- 59.100.10
- CCS
- Q36
- 发布
- 2010
- 实施
This method covers the determination of the percent loss on ignition of fiber glass mats. This ignition loss can be considered to be the binder content.
Loss on ignition of fiber glass mats
- ICS
- 59.100.10
- CCS
- Q36
- 发布
- 2010
- 实施
This practice defines the test conditions for testing fiber glass mats.
Test conditions for fiberglass mat test methods
- ICS
- 59.100.10
- CCS
- Q36
- 发布
- 2010
- 实施
This method covers the determination of the average fiber diameter (or distribution of diameters) of fibers used in nonwoven fiber glass mats.
Average fiber diameter of fiber glass mats
- ICS
- 59.100.10
- CCS
- Q36
- 发布
- 2010
- 实施
The purpose of this standard practice is to list existing TAPPI test methods which provide procedures for sampling and lot acceptance, stiffness, tear resistance, and thickness, and to suggest modifications to these methods for use in the sampling and testing of fiber glass mats.
Testing of fiber glass mats: use of modified TAPPI procedures for sampling and lot acceptance, stiffness, tear resistance, air permeability, and thickness
- ICS
- 59.100.10
- CCS
- Q36
- 发布
- 2010
- 实施
