共找到 577 条与 纺织玻璃纤维材料 相关的标准,共 39 页
本文件规定了电子级玻璃纤维坯布和成品布中空玻璃纤维含量的测定方法。 本文件适用于电子级玻璃纤维形成的增强织物。其他玻璃纤维可参照使用。
Determination of hollow glass filament content in electronic grade glass fiber fabric
本文件规定了电子级玻璃纤维布浸润性的测定方法。 本文件适用于电子级玻璃纤维为原料,经织造和表面化学处理而制成的电子级玻璃纤维布。
Determination of impregnation of electronic grade glass fiber fabrics
本文件规定了印制电路板用低介电玻璃纤维布经热处理后的白度的测定方法。 本文件适用于印制电路板用低介电玻璃连续纤维纱为原料制成的平面织物。
Determination of whiteness after heat treatment of low dielectric constant glass fiber woven for printed boards
This document specifies a system of designating textile glass yarns (including single, multiple-wound, folded (plied), cabled and textured yarns, strands, slivers and rovings) based on their linear density expressed in the tex system.
Textile glass — Yarns — Designation
本文件规定了过滤用亚克力针刺毡的技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本文件适用于过滤用亚克力针刺毡的生产和检验。
Acrylic needle felt for filtration
Standard Test Method for Determining Tensile Breaking Strength of Glass Fiber Reinforcing Mesh for Use in Class PB Exterior Insulation and Finish Systems (EIFS), after Exposure to a Sodium Hydroxide S
Standard Test Method for Tensile Properties of Glass Fiber Strands, Yarns, and Rovings Used in Reinforced Plastics
本标准规定了1017电子级玻璃纤维布的定义、开纤布的定义、经纱宽度及经纱开纤宽度的定义、代号与规格﹑要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于以E玻璃连续纤维纱为原料,经织造和表面化学处理而制成的平纹织物(以下简称产品),主要用作印制板用层压复合材料中的增强材料,其他用途也可参照此标准执行。
1017 E-glass fabric woven for printed boards
Standard Specification for Finished Woven Glass Fabrics
Standard Specification for Glass Fiber Cord and Sewing Thread
Standard Specification for Finished Glass Fabrics Woven From Rovings
Standard Specification for Glass Fiber Strands
1 Scope This document specifies a method for the determination of the average thickness , the thickness under load and the recovery after compression of chopped-strand and continuous-filament textile-glass mats.
Textile glass. Chopped-strand and continuous-filament mats. Determination of average thickness, thickness under load and recovery after compression
This document specifies a method for the determination of the average thickness, the thickness under load and the recovery after compression of chopped-strand and continuous-filament textile-glass mats.
Textile glass — Chopped-strand and continuous-filament mats — Determination of average thickness, thickness under load and recovery after compression
本文件描述了耐高温纤维织物的耐辐照性能的评价方法,确立了使用辐照前后断裂强力变化量评价纤维织物辐照效应的一般原则。
Estimate method of irradiation performance on heat preservation fibre fabric
1.1 This practice details procedures for establishing the direct stress and shear stress damage-based design values for use in the damage-based design criterion for materials to be used in GFRP vessels and other GFRP structures. The practice uses data derived from acoustic emission examination of four-point beam bending tests and in-plane shear tests (see ASME Section X, Article RT-8). 1.2 The onset of lamina damage is indicated by the presence of significant acoustic emission during the reload portion of load/reload cycles. “Significant emission” is defined with historic index. 1.3 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units which are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Standard Practice for Determining Damage-Based Design Stress for Glass Fiber Reinforced Plastic (GFRP) Materials Using Acoustic Emission
本文件相较于国家标准的指标先进性: ——断裂强度: 根据玻璃纤维组成和种类、 纤维直径等不同, 高于 GB/T 18371-2008《连续玻璃纤维纱》 和 GB/T 18369-2008《玻璃纤维无捻粗纱》 相关要求。 ——捻度允许偏差: 加捻纱捻度允许偏差为± 6%, 严于 GB/T 18371-2008 规定的± ( 8%~15%) 。 ——线密度允许偏差: 加捻纱为± 6%, 严于 GB/T 18371-2008 规定的± 8%; 直接无捻粗纱和合股无捻粗纱符合 GB/T 18369-2008 的规定。
Jiangxi Green Ecology-Glass fibre yarn
本文件规定了采光板用玻璃纤维无捻粗纱的产品分类和代号、要求、试验方法、检验规则、包装、标志、运输和贮存。 本文件适用于复合材料采光板用的玻璃纤维无捻粗纱。
Glass fiber roving for lighting board
1 Scope This document specifies a system of designating textile glass yarns (including single, multiple-wound, folded (plied), cabled and textured yarns, strands, slivers and rovings) based on their linear density expressed in the tex system.
Textile glass. Yarns. Designation
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号