共找到 2413 条与 皮革和裘皮 相关的标准,共 161 页
Leather - Leather for apparel (excluding furs) - Specifications and sampling procedures (ISO 14931:2021)
本文件规定了服装用绵羊皮革(以下简称为皮革)基本要求、技术要求、试验方法、检验规则、标志包装运输和贮存、质量承诺等要求。 本文件适用于以绵羊皮为主要原料经铬鞣或结合鞣法鞣制生产的服装用皮革。 本文件不适用于绒面皮革。
Sheep leather for apparel
Leather. Determination of chlorinated hydrocarbons in leather. Chromatographic method for short-chain chlorinated paraffins
Leather. Determination of chlorinated hydrocarbons in leather. Chromatographic method for middlechain chlorinated paraffins (MCCPs)
This document gives recommended values and related test methods for apparel leather, excluding furs. It also specifies the sampling and conditioning procedures of laboratory samples.
Leather - Leather for apparel (excluding furs) - Specifications and sampling procedures (ISO 14931:2021); German version EN ISO 14931:2021
Leather - Chemical determination of chromium(VI) content in leather - Thermal pre-ageing of leather and determination of hexavalent chromium (ISO 10195:2018)
Leather - Determination of chlorinated hydrocarbons in leather - Part 1: Chromatographic method for short-chain chlorinated paraffins (SCCPs) (ISO 18219-1:2021)
Leather - Tests for colour fastness - Colour fastness to migration into polymeric material (ISO/DIS 15701:2021)
Leather - Chemical tests - Determination of pesticide residues content (ISO 22517:2019)
Leather - Determination of chlorinated hydrocarbons in leather - Part 2: Chromatographic method for middle-chain chlorinated paraffins (MCCPs) (ISO 18219-2:2021)
Leather - Leather for apparel (excluding furs) - Specifications and sampling procedures (ISO 14931:2021)
ISO 17502:2013 specifies a method for determining the reflectance properties of a leather surface for visible and near infra-red radiation. The reflection value in the near infra-red determines if a leather may be classified as solar reflective. The method is applicable to all types of leather, in particular for coloured leather.
Leather — Determination of surface reflectance
ISO 17226-3:2011 specifies a method for determining the emission of formaldehyde from leathers. This method is based on high performance liquid chromatography (HPLC). It is selective and also allows the emission of other low molecular aldehydes and ketones to be observed. ISO 17226-3:2011 deals with the release of formaldehyde to the gas phase. Therefore, the obtained results are not comparable with the results of methods described in ISO 17726-1 and ISO 17226-2 which are based on extraction with liquid water.
Leather — Chemical determination of formaldehyde content — Part 3: Determination of formaldehyde emissions from leather
ISO 18218-1:2015 is a method for determining ethoxylated alkylphenols (nonyphenol ethoxylate [NPEOn with 1 ≤ n ≤ 16] and octylphenol ethoxylate [OPEOn with 1 ≤ n ≤ 16]) in leather. This direct method is especially suitable where a larger number of leather samples are to be checked for the presence of ethoxylated alkylphenols. This method requires the use of high-performance liquid chromatography (HPLC) with triple quadrupole mass spectrometer (MSMS) to identify and quantify the ethoxylated alkylphenols. NOTE 1 In the leather industry, the most commonly used commercial ethoxylated alkylphenol is the NPEO with an average of 9 EO. It has an optimum cloud point in water for the typical leather processing temperatures of 40 °C to 55 °C. NOTE 2 ISO 18218-1 and ISO 18218-2 use different solvents for the extraction of the ethoxylated alkylphenols from leather. Consequently, the two analytical methods are expected to give similar trends but not necessarily the same absolute result for the ethoxylated alkylphenol content in leather.
Leather — Determination of ethoxylated alkylphenols — Part 1: Direct method
ISO 3377-2:2016 specifies a method for determining the tear strength of leather using a double edged tear. The method is sometimes described as the Baumann tear. It is applicable to all types of leather.
Leather — Physical and mechanical tests — Determination of tear load — Part 2: Double edge tear
ISO 5402-2:2015 specifies a method for determining the wet or dry flex resistance of leather and finishes applied to leather. It is applicable to all types of leather below 3,0 mm in thickness.
Leather — Determination of flex resistance — Part 2: Vamp flex method
ISO 14931:2015 gives recommended values and related test methods for apparel leather excluding furs. It also specifies the sampling and conditioning procedures of laboratory samples.
Leather — Guide to the selection of leather for apparel (excluding furs)
ISO 19076:2016 provides a method for the measurement of the surface of leather or leather parts by the use of electronic measuring machines. It applies to the measurement of leather (or leather parts) fulfilling the following requirements: - flexible leather, finished or unfinished, dry or wet leather; - flexibility: such to allow full distension on the measuring line/surface.
Leather — Measurement of leather surface — Using electronic techniques
ISO 18219:2015 specifies a chromatographic method to determine the amount of short-chain chlorinated paraffins (SCCP) C10-C13 in processed and unprocessed leathers. Annex A is for information only.
Leather — Determination of chlorinated hydrocarbons in leather — Chromatographic method for short-chain chlorinated paraffins (SCCP)
ISO 3377-1:2011 specifies a method for determining the tear strength of leather using a single-edge tear. The method is sometimes described as a trouser tear. It is applicable to all types of leather.
Leather — Physical and mechanical tests — Determination of tear load — Part 1: Single edge tear
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号