共找到 2414 条与 皮革和裘皮 相关的标准,共 161 页
ISO 17502:2013 specifies a method for determining the reflectance properties of a leather surface for visible and near infra-red radiation. The reflection value in the near infra-red determines if a leather may be classified as solar reflective. The method is applicable to all types of leather, in particular for coloured leather.
Leather — Determination of surface reflectance
ISO 5402-2:2015 specifies a method for determining the wet or dry flex resistance of leather and finishes applied to leather. It is applicable to all types of leather below 3,0 mm in thickness.
Leather — Determination of flex resistance — Part 2: Vamp flex method
ISO 17226-3:2011 specifies a method for determining the emission of formaldehyde from leathers. This method is based on high performance liquid chromatography (HPLC). It is selective and also allows the emission of other low molecular aldehydes and ketones to be observed. ISO 17226-3:2011 deals with the release of formaldehyde to the gas phase. Therefore, the obtained results are not comparable with the results of methods described in ISO 17726-1 and ISO 17226-2 which are based on extraction with liquid water.
Leather — Chemical determination of formaldehyde content — Part 3: Determination of formaldehyde emissions from leather
ISO 17489:2013 specifies a simple and practical method of determining the adsorbable fraction of synthetic tanning agents using a polymer-based product. It is particularly suitable for measuring the batch-to-batch consistency of synthetic tanning agents.
Leather — Chemical tests — Determination of tan content in synthetic tanning agents
ISO 19071:2016 specifies a test method for the determination of chromium (VI) content in chromium tanning agents. The results give information about the reductive potential of the chromium tanning agent.
Leather — Chemical tests — Determination of chromium (VI) and the reductive potential for chromium tanning agents
ISO 19074:2015 specifies a method for determining the rate of absorption of water by capillary action or wicking in leathers. It is applicable to all types of leather.
Leather — Physical and mechanical tests — Determination of water absorption by capillary action (wicking)
ISO 3377-1:2011 specifies a method for determining the tear strength of leather using a single-edge tear. The method is sometimes described as a trouser tear. It is applicable to all types of leather.
Leather — Physical and mechanical tests — Determination of tear load — Part 1: Single edge tear
ISO 17130:2013 specifies a method of determining the dimensional change (shrinkage) of leathers caused by ageing. It is applicable to all leathers.
Leather - Physical and mechanical tests - Determination of dimensional change
This document specifies a thermal pre-ageing procedure for leather to obtain indications about the tendency to the formation of hexavalent chromium under specified conditions and the determination of hexavalent chromium according to ISO 17075‑1 or ISO 17075‑2. This thermal pre-ageing procedure does not simulate any real condition in leather production or use. It is applicable to all types of chromium tanned leather.
Leather — Chemical determination of chromium(VI) content in leather — Thermal pre-ageing of leather and determination of hexavalent chromium
ISO 19070:2016 specifies a method to determine the amount of N-methyl-2-pyrrolidone (NMP) in leather and leather components. This method may also be used for the determination of N-ethyl-2-pyrrolidone (NEP) in leather.
Leather — Chemical determination of N-methyl-2-pyrrolidone (NMP) in leather
ISO 14931:2015 gives recommended values and related test methods for apparel leather excluding furs. It also specifies the sampling and conditioning procedures of laboratory samples.
Leather — Guide to the selection of leather for apparel (excluding furs)
ISO 3377-2:2016 specifies a method for determining the tear strength of leather using a double edged tear. The method is sometimes described as the Baumann tear. It is applicable to all types of leather.
Leather — Physical and mechanical tests — Determination of tear load — Part 2: Double edge tear
Leather - Physical and mechanical tests - Determination of bending force (ISO/DIS 14087:2021)
Leather - Leather for apparel (excluding furs) - Specifications and sampling procedures (ISO 14931:2021)
Leather – Determination of chlorinated hydrocarbons in leather – Part 2: Chromatographic method for middle-chain chlorinated paraffins (MCCPs)
Leather – Determination of chlorinated hydrocarbons in leather – Part 1: Chromatographic method for short-chain chlorinated paraffins (SCCPs)
Leather. Chemical determination of formaldehyde content. Method using high-performance liquid chromatography
Leather – Determination of chlorinated hydrocarbons in leather – Part 1: Chromatographic method for short-chain chlorinated paraffins (SCCPs) (ISO 18219-1:2021)
Leather - Physical and mechanical tests - Determination of dimensional change (ISO 17130:2021)
Leather - Chemical tests - Determination of free formaldehyde in process auxiliaries (ISO 27587:2021)
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号