61.040 帽子、服饰品、衣扣 标准查询与下载

DS/CEN/TR 15118:2005 接触和关闭紧固件的测试指南

This Technical Report describes different methods of integration of touch and close fasteners to the final or finished product, such as:Sewing,mechanical attachment,adhesive pressure sensitive,heat activated,welded attachment,moulding in, straps,non-continous application in various widths,together with the appropriate test method.

Testing guidelines for touch and close fasteners

PD CEN/TR 15118:2005 粘合拉锁的试验指南

This Technical Report describes different methods of integration of touch and close fasteners toThe final or finished product, such as:Sewing, mechanical attachment, adhesive pressure sensitive, heat activated, welded attachment, moulding in, straps, non-continous application in various widths, together withThe appropriate test method.

Testing guidelines for touch and close fasteners

ASTM D2057-05(2015) 拉链水洗色牢度的标准试验方法

5.1 Test Method D2057 is useful for testing to determine if the degree of alteration in shade is satisfactory for the intended end-use and for determining if unacceptable staining of color into adjacent fabric will occur. Note 1: For guidance in evaluating the results of this method, refer to Practice D3692. 5.2 This test method is considered satisfactory for acceptance testing of commercial shipments because the method has been used extensively in the trade for acceptance testing. 5.2.1 If there are differences of practical significance between reported test results for two laboratories (or more), comparative tests should be performed to determine if their is a statistical bias between them, using competent statistical assistance. As a minimum, the test samples should be used that are as homogeneous as possible, that are drawn from the material from which the disparate test results were obtained, and that are randomly assigned in equal numbers to each laboratory for testing. Other materials with established test values may be used for this purpose. The test results from the two laboratories should be compared using a statistical test for unpaired data, at a probability level chosen prior to the testing series. If a bias is found, either its cause must be found and corrected, or future test results must be adjusted in consideration of the known bias. 5.3 The method(s) in this standard along with those in D2051, D2052, D2053, D2054, D2058, D2059, D2060, D2061, and D2062 are a collection of proven zipper test methods. They can be used as aids in the evaluation of zippers without the need for a thorough knowledge of zippers. The enumerated test methods do not provide for the evaluation of all zipper properties. Besides those properties measured by means of the enumerated test methods there are other properties that may be important for the satisfactory performance of a zipper. Test methods for measuring those properties have not been published either because no practical methods have yet been developed or because a valid evaluation of the information resulting from existing unpublished methods requires an intimate and thorough knowledge of zippers. 1.1 This test method covers the determination of alteration in shade and of staining under conditions similar to that experienced in domestic washing of zipper stringers. This test method is applicable to the textile portion of zipper stringers that utilize tapes made of cotton, linen, or manufactured organic fibers, and to combinations thereof. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as the standard. Within the text, the inch-pound units are shown in parentheses. The values stated in each system are not exact equivalents; therefore, each system shall be used inde......

Standard Test Method for Colorfastness of Zippers to Laundering

ASTM D2057-05(2010) 水洗时拉链色牢度的标准试验方法

Test Method D2057 is useful for testing to determine if the degree of alteration in shade is satisfactory for the intended end-use and for determining if unacceptable staining of color into adjacent fabric will occur. Note 18212;For guidance in evaluating the results of this method, refer to Practice D3692. This test method is considered satisfactory for acceptance testing of commercial shipments because the method has been used extensively in the trade for acceptance testing. If there are differences of practical significance between reported test results for two laboratories (or more), comparative tests should be performed to determine if their is a statistical bias between them, using competent statistical assistance. As a minimum, the test samples should be used that are as homogeneous as possible, that are drawn from the material from which the disparate test results were obtained, and that are randomly assigned in equal numbers to each laboratory for testing. Other materials with established test values may be used for this purpose. The test results from the two laboratories should be compared using a statistical test for unpaired data, at a probability level chosen prior to the testing series. If a bias is found, either its cause must be found and corrected, or future test results must be adjusted in consideration of the known bias. The method(s) in this standard along with those in D2051, D2052, D2053, D2054, D2058, D2059, D2060, D2061, and D2062 are a collection of proven zipper test methods. They can be used as aids in the evaluation of zippers without the need for a thorough knowledge of zippers. The enumerated test methods do not provide for the evaluation of all zipper properties. Besides those properties measured by means of the enumerated test methods there are other properties that may be important for the satisfactory performance of a zipper. Test methods for measuring those properties have not been published either because no practical methods have yet been developed or because a valid evaluation of the information resulting from existing unpublished methods requires an intimate and thorough knowledge of zippers.1.1 This test method covers the determination of alteration in shade and of staining under conditions similar to that experienced in domestic washing of zipper stringers. This test method is applicable to the textile portion of zipper stringers that utilize tapes made of cotton, linen, or manufactured organic fibers, and to combinations thereof. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as the standard. Within the text, the inch-pound units are shown in parentheses. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. combining values from the two systems may result in nonconformance with this test method. 1.3 This standard does not purp......

Standard Test Method for Colorfastness of Zippers to Laundering

ASTM D2052-05(2010) 拉链耐干洗色牢度的标准试验方法

Test Method D2052 is useful for testing to determine if the degree of alteration in shade is satisfactory for the intended end-use and for determining if unacceptable staining of color into adjacent fabric will occur. Note 18212;For guidance in evaluating the results of this test method, refer to Practice D3692. This test method is considered satisfactory for acceptance testing of commercial shipments because the method has been used extensively in the trade for acceptance testing. If there are differences of practical significance between reported test results for two laboratories (or more), comparative tests should be performed to determine if their is a statistical bias between them, using competent statistical assistance. As a minimum, the test samples should be used that are as homogeneous as possible, that are drawn from the material from which the disparate test results were obtained, and that are randomly assigned in equal numbers to each laboratory for testing. Other materials with established test values may be used for this purpose. The test results from the two laboratories should be compared using a statistical test for unpaired data, at probability level chosen prior to the testing series. If a bias is found, either its cause must be found and corrected, or future test results must be adjusted in consideration of the known bias. The method(s) in this standard along with those in Test Methods D2051, D2053, D2054, D2057, D2058, D2059, D2060, D2061, and D2062 are a collection of proven zipper test methods. They can be used as aids in the evaluation of zippers without the need for a thorough knowledge of zippers. The enumerated test methods do not provide for the evaluation of all zipper properties. Besides those properties measured by means of the enumerated test methods there are other properties that may be important for the satisfactory performance of a zipper. Test methods for measuring those properties have not been published either because no practical methods have yet been developed or because a valid evaluation of the information resulting from existing unpublished methods requires an intimate and thorough knowledge of zippers.1.1 This test method covers the determination of change in shade and of staining of zipper stringers under drycleaning conditions. This test method is applicable to the textile portion of zipper stringers of all materials. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as the standard. Within the text, the inch-pound units are shown in parentheses. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with this test method. 1.3 This standard does not purport to address all of the safety problems associated with its use. It is the responsibility of whoever uses t......

Standard Test Method for Colorfastness of Zippers to Drycleaning

ASTM D2052-05(2015) 拉链干洗色牢度的标准试验方法

5.1 Test Method D2052 is useful for testing to determine if the degree of alteration in shade is satisfactory for the intended end-use and for determining if unacceptable staining of color into adjacent fabric will occur. Note 1: For guidance in evaluating the results of this test method, refer to Practice D3692. 5.2 This test method is considered satisfactory for acceptance testing of commercial shipments because the method has been used extensively in the trade for acceptance testing. 5.2.1 If there are differences of practical significance between reported test results for two laboratories (or more), comparative tests should be performed to determine if their is a statistical bias between them, using competent statistical assistance. As a minimum, the test samples should be used that are as homogeneous as possible, that are drawn from the material from which the disparate test results were obtained, and that are randomly assigned in equal numbers to each laboratory for testing. Other materials with established test values may be used for this purpose. The test results from the two laboratories should be compared using a statistical test for unpaired data, at probability level chosen prior to the testing series. If a bias is found, either its cause must be found and corrected, or future test results must be adjusted in consideration of the known bias. 5.3 The method(s) in this standard along with those in Test Methods D2051, D2053, D2054, D2057, D2058, D2059, D2060, D2061, and D2062 are a collection of proven zipper test methods. They can be used as aids in the evaluation of zippers without the need for a thorough knowledge of zippers. The enumerated test methods do not provide for the evaluation of all zipper properties. Besides those properties measured by means of the enumerated test methods there are other properties that may be important for the satisfactory performance of a zipper. Test methods for measuring those properties have not been published either because no practical methods have yet been developed or because a valid evaluation of the information resulting from existing unpublished methods requires an intimate and thorough knowledge of zippers. 1.1 This test method covers the determination of change in shade and of staining of zipper stringers under drycleaning conditions. This test method is applicable to the textile portion of zipper stringers of all materials. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as the standard. Within the text, the inch-pound units are shown in parentheses. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with this test met......

Standard Test Method for Colorfastness of Zippers to Drycleaning

GSO 277:2004 男士头饰 棉质 Shemagh 和多酯 Shemagh 与棉和合成纤维混合

This Gulf standard is concerned with 100% cotton shemagh and polyester shemagh or blended cotton and polyester or viscose or acrylic shemagh used as a head cloth for men and boys.

HEAD CLOTH FOR MEN - COTTON SHEMAGH AND POLYESTER SHEMAGH OR BLENDED COTTON AND SYNTHETIC FIBRES SHEMAGH

GSO 227:2004 男士头饰：白色古特拉

This Gulf standard is concerned with white ghautra woven from cotton yarns 100% and used as head cloth for men and boys.

HEAD CLOTH FOR MEN : WHITE GHAUTRA

SANS 5451:2004 纽扣的干洗色牢度

Specifies a method for the determination of the colour fastness of buttons to dry cleaning.

Colour fastness of buttons to dry cleaning

BS EN 13780:2003 粘接拉链.纵向剪切强度的测定

This European Standard specifies a method for determining the longitudinal shear strength of a touch and close fastener.

Touch and close fasteners - Determination of longitudinal shear strength

BS EN 13780:2004 粘接拉链.纵向剪切强度的测定

Touch and close fasteners - Determination of longitudinal shear strength

ASTM D2059-03 拉链对盐雾（雾）的阻力的标准测试方法

1.1 This test method covers the determination of the resistance of all types of zippers to corrosion and their ability to function properly after exposure of specified duration in a prescribed salt spray.1.2 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Resistance of Zippers to Salt Spray (Fog)

LST EN 13780-2003 接触和关闭紧固件 纵向剪切强度的测定

Touch and close fasteners - Determination of longitudinal shear strength

GSO 226:2003 测试男士头巾的方法：白色 ghutra

This Gulf standard is concerned with methods of testing white ghautra made of 100% cotton and used as a head cloth for men and boys.

METHODS OF TEST FOR HEAD CLOTH FOR MEN — WHITE GHAUTRA

GSO 276:2003 男士头饰的测试方法 棉制谢马、聚酯谢马以及棉与合成纤维的混纺品

This Gulf standard is concerned with methods of testing of 100% cotton shemagh and polyester shemagh or blended cotton and synthetic fibres shemagh used as a head cloth for men and boys.

METHODS OF TESTING OF HEAD CLOTH FOR MEN — COTTON SHEMAGH AND POLYESTER SHEMAGH BLENDED OR COTTON SYNTHETIC FIBRES SHEMAGH

AS 2332:2003 拉链

Sets out requirements for slide fasteners which include strength and durability, colourfastness and dimensional stability. A classification system based on chain width is specified with performance classes ranging from ultra light to ultra heavy. Propert

Slide fasteners

DB42/ 248-2003 床罩　枕套

本标准规定了床罩、枕套产品的要求、试验方法、检验规则及标志、包装、运输和贮存。本标准适用于机织面料制作的的床罩、枕套。

Bedspread Pillowslip

DB42/ 249-2003 枕芯

本标准规定了枕芯的要求、试验方法、检验规则及标志、包装、运输和贮存。本标准适用于以一定压缩回弹性的纤维类物质为填充物，以各种面料为套子的枕芯，不适用于药枕、羽绒枕芯等有特殊用途的枕芯。

Pillow

DB42/ 247-2003 蚊帐

本标准规定了蚊帐的要求、试验方法、检验规则以及标志、包装、运输、贮存。本标准适用于以棉、苎麻、化纤、混纺织物为原料制成的蚊帐。

mosquito net

CNS 1082-2003 拉炼

本标准适用于以金属、塑料链齿组成之布带拉链(亦称拉炼)

Zippers