61.040 帽子、服饰品、衣扣 标准查询与下载

ASTM D2052-01 拉链色牢度耐干洗性的标准试验方法

1.1 This test method covers the determination of change in shade and of staining of zipper stringers under drycleaning conditions. This test method is applicable to the textile portion of zipper stringers of all materials.1.2 The values stated in either SI units or inch-pound units are to be regarded separately as the standard. Within the text, the inch-pound units are shown in parentheses. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with this test method.1.3 This standard does not purport to address all of the safety problems associated with its use. It is the responsibility of whoever uses this standard to consult and establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Colorfastness of Zippers to Drycleaning

ASTM D4153-01(2012) 男人、妇女和儿童用机织手帕织物的标准性能规格

Upon mutual agreement between the purchaser and the supplier, fabrics intended for this end use should meet all of the requirements listed in Table 1 of this specification. It is recognized that for purposes of fashion or aesthetics the ultimate consumer of articles made from these fabrics may find acceptable fabrics that do not conform to all of the requirements in Table 1. Therefore, one or more of the requirements listed in Table 1 may be modified by mutual agreement between the purchaser and the supplier. In such cases, any references to the specification shall specify that: “This fabric meets ASTM Specification D4153 except for the following characteristic(s).” Where no prepurchase agreement has been reached between the purchaser and the supplier, and in case of controversy, the requirements listed in Table 1 are intended to be used as a guide only. As noted in 5.2, ultimate consumer demands dictate varying performance parameters for any particular style of fabric. The uses and significance of particular properties and test methods are discussed in the appropriate sections of the specified test methods.1.1 This performance specification covers woven fabrics to be used in the manufacture of men''s, women''s, and children''s handkerchiefs, both utilitarian and decorative. 1.2 This performance specification is not applicable to open-work fabrics such as lace which is used primarily to decorate handkerchiefs, or woven fabrics used for the manufacture of scarves. 1.3 These requirements apply to both the length and width directions for those properties where fabric direction is pertinent. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Performance Specification for Men's, Women's, and Children's Woven Handkerchief Fabrics

LST EN 1414+A1-2000 接触和关闭紧固件 后续测试的循环程序

Touch and close fasteners - Cycling procedure for subsequent testing

LST EN 1416-2000 接触和关闭紧固件 曲率的测定

Touch and close fasteners - Determination of curvature

LST EN 12243-2000 接触和关闭紧固件 洗涤和干燥以及干洗中尺寸变化的测定

Touch and close fasteners - Determination of dimensional change in washing and drying and dry cleaning

LST EN 1415-2000 接触并关闭紧固件 缝边的行为

Touch and close fasteners - Behaviour of slit selvedges

LST EN 12240-2000 接触和闭合紧固件 胶带的总宽度和有效宽度以及闭合件的有效宽度的测定

Touch and close fasteners - Determination of the overall and effective widths of tapes and the effective width of a closure

DIN EN 1414:2000 接触锁紧紧固件.后续试验的循环过程(包括补充件A1,2000)

Touch and close fasteners - Cycling procedure for subsequent testing (includes Amendment A1:2000); German version EN 1414:1996 + A1:2000

ASTM D2060-00 测量拉链尺寸的标准测试方法

1.1 These test methods cover the measurement of the dimensions of all types and sizes of zippers.1.2 The test methods appear as follows: SectionsChain Flatness34-39Chain Straightness40-44Chain Thickness28-33Length of Zipper or Parts9-14Longitudinal Dimensional Change45-52Slider Mouth Width21-27Tape Width15-201.3 The values stated in either SI units or in other units shall be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system must be used independently of the other, without combining values in any way.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Measuring Zipper Dimensions

DS/EN 1414/A1:2000 接触和关闭紧固件 后续测试的循环程序

This standard holds an addition to EN 1411 dealing with pretension and having a more detailed sketch of the apparatus for submitting touch and close fasteners to opening and closing cycles in order to simulate use. The apparatus is used to open and close a touch and close fastener of specified width a specified number of times. The touch and close fasteners subjected to these cycles will be used in subsequent physical tests intended to measure the residual mechanical strength characteristics.

Touch and close fasteners - Cycling procedure for subsequent testing

DLA MIL-DTL-44132 C-2000 空军用微气候条件背心

The General Services Administration has authorized the use of this commercial item description as a replacement for Military Specifications MIL-V-16720E and MIL-V-16721D which are cancelled.

VEST, CONDITIONING MICROCLIMATE: AIR

DS/EN 12242:2000 接触和关闭紧固件 剥离强度的测定

Mated component tapes of a touch and close fastener are separated at a constant rate in a peeling action from an open edge of a prepared closure. This is carried out such that the separation occurs progressively along the closure in a direction parallel to the length of the tapes forming the closure.

Touch and close fasteners - Determination of peel strength

DS/EN 12241:2000 接触和关闭紧固件 洗涤和干燥或干洗前的关闭方法

This standard describes a method where male and female tapes of a touch and close fastener are pressed together in a controlled manner by passing a prescribed metal roller over the mated tapes.

Touch and close fasteners - Method for closure prior to washing and drying or dry cleaning

DS/EN 12243:2000 接触和关闭紧固件 洗涤和干燥以及干洗中尺寸变化的测定

This stadard specifies determination of the percentage change in the length of touch and close fastener tapes after dry cleaning and/or washing and drying.

Touch and close fasteners - Determination of dimensional change in washing and drying and dry cleaning

ASTM D5171-00 塑料贯穿法兰钮扣抗冲击性的标准试验方法

1.1 This test method covers the determination of impact resistance of plastic sew-through flange buttons. 1.2 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.3 The values stated in either acceptable metric units or other units shall be regarded separately as standard. The values expressed in each system may not be exact equivalents; therefore, each system must be used independently of each other, without combining values in any way.

Standard Test Method for Impact Resistance of Plastic Sew-Through Flange Buttons

BS EN 12242:2000 碰触和闭锁扣件.剥离强度测定

This European Standard specifies a method for determining the peel strength of a touch and close fastener.

Touch and close fasteners - Determination of peel strength

BS EN 12241:2000 碰触和闭锁扣件.清洗,干燥和干洗期间的封闭方法

This European Standard specifies a method for closing a touch and close fastener, prior to washing and drying or dry cleaning.

Touch and close fasteners - Method for closure prior to washing and drying or dry cleaning

BS EN 12243:2000 碰触和闭锁扣件.清洗,干燥和干洗中尺寸变化测定

This European Standard specifies a method for determining the dimensional change in washing and drying or dry cleaning of touch and close fastener tapes.

Touch and close fasteners - Determination of dimensional change in washing and drying and dry cleaning

ASTM D2060-00(2010) 测量拉链尺寸的标准试验方法

The significance of specific tests is discussed in the appropriate sections. These test methods are considered satisfactory for acceptance testing of commercial shipments because the test methods have been used extensively in the trade for this purpose, and because current estimates of between-laboratory precision are acceptable in most cases. In case of a dispute arising from differences in reported test results when using Test Methods D2060 for acceptance testing of commercial shipments, the purchaser and the supplier should conduct comparative tests to determine if there is a statistical bias between their laboratories. Competent statistical assistance is recommended for the investigation of bias. As a minimum, the two parties should take a group of test specimens that are as homogeneous as possible and that are from a lot of material of the type in question. The test specimens should then be randomly assigned in equal numbers to each laboratory for testing. The average results from the two laboratories should be compared using Student''s t-test for unpaired data and an acceptable probability level chosen by the two parties before the testing is begun. If a bias if found, either its cause must be found and corrected or the purchaser and the supplier must agree to interpret future test results in the light of the known bias. The test method(s) in these test methods, along with those in Test Methods D2051, D2052, D2053, D2054, D2057, D2058, D2059, D2061, and D2062, are a collection of proven test methods. They can be used as aids in the evaluation of zippers without the need for a thorough knowledge of zippers. The enumerated test methods do not provide for the evaluation of all zipper properties. Besides those properties measured by means of the enumerated test methods there are other properties that may be important for the satisfactory performance of a zipper. Test methods for measuring those properties have not been published either because no practical methods have yet been developed or because a valid evaluation of the information resulting from existing unpublished methods requires an intimate and thorough knowledge of zippers.1.1 These test methods cover the measurement of the dimensions of all types and sizes of zippers. 1.2 The test methods appear as follows:

Standard Test Methods for Measuring Zipper Dimensions

SANS 1822:2000 拉锁

This standard specifies requirements for four types and five performance classes of slide fasteners with individual metallic or synthetic teeth or spirals/coils.

Slide fasteners