脂族烃标准-分析测试百科网

KS M 1052-2005(2010) 纯十二烷

High purity dodecane

ICS: 71.080.10
CCS
发布: 2005-11-01
实施

TIS 2068-2001 工业己烷

Industrial hexane

ICS: 71.080.10
CCS
发布: 2005-06-13
实施

SH/T 1726-2004 工业用异丁烯

Isobutene for industrial use--Specification

ICS: 71.080.10
CCS: G16
发布: 2004-04-09
实施: 2004-09-01

ASTM D5248-04(2010) 再生的1,1,2-三氯1,2,2-三氟乙烷标准规范

1.1 This specification covers the three grades of 1,1,2-trichloro 1,2,2-trifluoroethane typically needed in various industries. It may be used as a reference document by purchasers or by persons establishing in-house, 1,1,2-trichloro 1,2,2-trifluoroethane recovery programs.

Standard Specification for Reclaimed 1,1,2-Trichloro 1,2,2-Trifluoroethane

ICS: 71.080.10
CCS: G16
发布: 2004
实施

ASTM D6100-03 挤出压缩模塑和注射模塑缩醛形状（POM）的标准规范

1.1 This specification covers requirements and test methods for the material, dimensions, and workmanship, and the properties of extruded, compression molded and injection molded acetal sheet, plate, rod, and tubular bar manufactured from acetal.1.2 The properties included in this specification are those required for the compositions covered. Requirements necessary to identify particular characteristics important to specialized applications may be described by using the classification system given in Section 4.1.3 This specification allows for the use of recycled plastics as defined in Guide D 5033.1.4 The values stated in inch-pound units are to be regarded as the standard in all property and dimensional tables. For reference purposes, SI units are included in Table S-POM and Table 1 only.1.5 The following precautionary caveat pertains only to the test method portions, Section 11, of this specification:This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.Note 18212;There is no similar or equivalent ISO Standard.

Standard Specification for Extruded, Compression Molded and Injection Molded Acetal Shapes (POM)

ICS: 71.080.10
CCS
发布: 2003-07-10
实施

TIS 2069-2001 橡胶溶剂

Rubber solvent

ICS: 71.080.10
CCS
发布: 2003-06-30
实施

KS M ISO 7382-2002(2012) 工业用乙烯液态和气态采样法

Ethylene for industrial use－Sampling in the liquid and the gaseous phase

ICS: 71.080.10
CCS
发布: 2002-12-30
实施

KS M ISO 8563-2002(2012) 工业用丙烯和丁二烯液态采样法

Propylene and butadiene for industrial use－Sampling in the liquid phase

ICS: 71.080.10
CCS
发布: 2002-12-30
实施

ASTM D1836-02 商业己烷的标准规格

1.1 This specification covers the range of products commonly referred to as hexanes, which find uses in the preparation of adhesives, coatings, and printing inks, as raw materials in chemical synthesis operations, and as solvents in various kinds of extraction operations.1.2 The following applies to all specified limits in this standard; for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off "to the nearest unit" in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E 29.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.1.4 For specific hazard information and guidance consult supplier's Material Safety Data Sheet.

Standard Specification for Commercial Hexanes