71.080.80 醛和酮 标准查询与下载

KS M 1959-2017 工业用甲乙酮试验方法一览表

Methyl ethyl ketone for industrial use－List of methods of test

KS M 1968-2017 工业乙醛——密度的测定 (15°C)

Acetaldehyde for industrial use — Determination of density at 15℃

KS M 1982-2017 工业用正丁醇、甲乙酮、异丁基甲基酮、异戊基乙基酮、双丙酮醇、己二醇 酚酞酸度的测定 容量法

SecButyl alcohol, methyl ethyl ketone, isobutyl methyl ketone, isoamyl ethyl ketone, diacetone alcohol and hexylene glycol for industrial use — Determination of acidity to phenolphthalein — Volumetric method

KS M 1968-2017(2022) 工业用乙醛.15℃下密度的测定

Acetaldehyde for industrial use — Determination of density at 15℃

KS M 1982-2017(2022) 工业用正丁醇、甲基乙基酮、异丁基甲基酮、异戊基乙基酮、二丙酮和己二醇.酚酞酸度的测定.容量法

SecButyl alcohol, methyl ethyl ketone, isobutyl methyl ketone, isoamyl ethyl ketone, diacetone alcohol and hexylene glycol for industrial use — Determination of acidity to phenolphthalein — Volumetric

KS M 1959-2017(2022) 工业用甲乙酮－试验方法列表

Methyl ethyl ketone for industrial use－List of methods of test

ASTM D3893-03(2017) 用气相色谱法测定甲基戊基酮和甲基异戊基酮的纯度的标准试验方法

1.1 This test method covers the determination of the purity of methyl amyl ketone and methyl isoamyl ketone. In addition, the method determines total ketones and various impurities which may include acetone, isopropyl alcohol, methyl propyl ketone, methyl isobutyl ketone, methyl butyl ketone, methyl isobutyl carbinol, mesityl oxide, methyl isoamyl ketone, methyl butyl carbinol, methyl amyl ketone, and diisobutyl ketone. 1.2 Water and acid cannot be determined by this test method. They must be determined by other appropriate ASTM procedures, and the results used to normalize the chromatographic data. 1.3 For purposes of determining conformance of an observed or a calculated value using this test method to relevant specifications, test result(s) shall be rounded “off to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 For hazard information and guidance, see the supplier’s Safety Data Sheet. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Purity of Methyl Amyl Ketone and Methyl Isoamyl Ketone by Gas Chromatography

ASTM D1614-09(2017) 丙酮中碱度的标准试验方法

1.1 This test method covers the determination in acetone of alkalinity calculated as ammonia (NH3). 1.2 The following applies to all specified limits in this standard; for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 For specific hazard information and guidance, consult the supplier’s Safety Data Sheet. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific hazard statements are given in Section 7. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Alkalinity in Acetone

ASTM D2379-09(2017) 甲醛溶液酸度的标准试验方法

1.1 This test method covers the determination of the acidity of commercially available formaldehyde solutions. 1.2 For purposes of determining conformance of an observed or a calculated value using this test method to relevant specifications, test result(s) shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 For hazard information and guidance, see the supplier’s Safety Data Sheet. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific hazard statements are given in Section 7. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Acidity of Formaldehyde Solutions

ASTM D2916-09(2017) 异佛尔酮的标准规范

1.1 This specification covers isophorone2 (98 % grade) for use in paint, varnish, lacquer, and related products. 1.2 The following applies to all specified limits in this standard; for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 For specific hazard information and guidance, see the supplier’s Safety Data Sheet for materials listed in this specification. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Isophorone

ASTM D3329-03(2017) 用气相色谱法测定甲基异丁基酮纯度的标准试验方法

1.1 This test method covers the determination of the purity of methyl isobutyl ketone (MIBK) by gas chromatography and in addition provides a means for measuring certain impurities such as methyl isobutyl carbinol which are of interest. Impurities such as water and acidity are measured by other appropriate ASTM procedures and the results are used to normalize the chromatographic value. 1.2 The following applies to all specified limits in this standard; for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the round-off method of Practice E29. 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 For specific hazard information and guidance, see the supplier’s Safety Data Sheet for the materials listed in this test method. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Purity of Methyl Isobutyl Ketone by Gas Chromatography

HG/T 5275-2017 工业用乙二醛水溶液

Glyoxal aqueous solution for industrial use

HG/T 5149-2017 工业用乙醛

Industrial acetaldehyde

HG/T 5148-2017 异佛尔酮

Isophorone

ASTM E411-17a 羰基化合物与2,4-二硝基苯肼痕量的标准试验方法

1.1 This test method covers the determination of total carbonyl in the range from 0.5 to 50 µg calculated as CO. 1.2 This test method is intended to be general and does not include steps for sample preparation. 1.3 Acetals that hydrolyze under the conditions of the test are also determined. 1.4 Carbonyl derivatives such as acetals and imines that are easily hydrolyzed may be determined by an alternative procedure. 1.5 The developed color is not stable and must be measured within a specified period. NOTE 1—Other test methods for the determination of traces of carbonyl compounds are given in Test Methods D1089, D1612, D2119, and D2191. 1.6 Review the current appropriate Safety Data Sheets (SDS) for detailed information concerning toxicity, first aid procedures, and safety precautions. 1.7 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific hazards statements are given in Section 7 and Section 8. 1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Trace Quantities of Carbonyl Compounds with 2,4-Dinitrophenylhydrazine

ASTM E411-17 羰基化合物与2,4-二硝基苯肼痕量的标准试验方法

Standard Test Method for Trace Quantities of Carbonyl Compounds with 2,4-Dinitrophenylhydrazine

KS M 1665-2016 工业用丙酮

Acetone for industrial use

ASTM D5197-16 空气中甲醛和其他羰基化合物的测定标准试验方法（主动取样方法）

Standard Test Method for Determination of Formaldehyde and Other Carbonyl Compounds in Air (Active Sampler Methodology)

HG/T 4965-2016 工业用异丁醛

Industrial isobutyraldehyde

GOST 1625-2016 工业用福尔马林. 规格

Formalin for industrial use. Specifications