73.100.10 巷道掘进和敷设管道设备 标准查询与下载

JB/T 3904-2006 凿岩机械与气动工具 金属型、砂型 铸造铝合金铸件通用技术条件

本标准规定了凿岩机械与气动工具金属型、砂型铸造铝合金铸件的分类及检验项目。 本标准适用于凿岩机械与气动工具金属型、砂型铸造铝合金铸件，并与JB/T 3905配套使用。

General specifications for metal and sand casting aluminium alloy of rock drilling machines and pneumatic tools

JB/T 3905-2006 凿岩机械与气动工具 铸造铝合金通用技术条件

本标准规定了凿岩机械与气动工具铸造铝合金的化学成分、力学性能、晶粒度、含气量及变质效果等。 本标准适用于凿岩机械与气动工具铸造铝合金，并与JB/T 3904 配套使用。

General specifications for casting aluminium alloy of rock drilling machines and pneumatic tools

JB/T 7301-2006 手持式凿岩机

本标准规定了手持式凿岩机的型式与基本参数、技术要求、检验方法、检验规则和标志、包装、运输与贮存。 本标准适用于以压缩空气为动力的手持式凿岩机（以下简称产品）。

Hand-held rock drills

JB/T 6123-2006 转盘式竖井钻机

本标准规定了转盘式竖井钻机的结构形式、基本参数、技术要求、试验方法、检验规则及标志、包装、运输和贮存。 本标准适用于矿山的大中型和其他工程大型钻井施工用，以液压或机械传动且以转盘回转钻具的转盘式竖井钻机，适用于冲积层、岩石层（岩石单轴极限抗压强度≤160MPa）钻进，钻凿铅垂井。

Rotarytable shaft drilling machine

MT 112.1-2006 矿用单体液压支柱.第1部分.通用要求

MT 112的本部分规定了矿用单体液压支柱（含注液枪）的术语和定义、分类、要求、试验方法、检验规则、标志、包装、运输和贮存。 本部分适用于矿用单体液压支柱（以下简称支柱）的制造、检验和评定。

Hydraulic signle prop for coal mine.Part 1:General requirements

MT/T 112.1-2006 矿用单体液压支柱 第1部分 通用要求

Single hydraulic prop for mining - Part 1 General requirements

MT/T 238.3-2006 悬臂式掘进机.第3部分：通用技术条件

本标准规定了悬臂式掘进机的术语和定义、要求、试验方法、检验规则以及标志、包装、运输及贮存。 本标准适用于还有瓦斯、煤尘或其他爆炸性混合气体中作业的悬臂式掘进机（以下简称掘进机），也适用于其他工程巷道中作业的同类掘进机。

Boom-type roadheader.Part 3:General technical condition

MT/T 188.1-2006 煤矿用乳化液泵站.第1部分:泵站

MT/T 188的本部分规定了煤矿用乳化液泵站（以下简称泵站）的术语和定义、产品分类、要求、试验方法、检验规则、标志、包装和贮存。 本部分适用于煤矿井下以高含水液压液（含乳化液）为工作介质的乳化液泵站，也适用于煤矿井下以清水为工作介质的喷雾灭尘泵站和注水泵站。

Emulsion pump station for coal mine.Part 1:Pump station

MT/T 98-2006 液压支架用软管及软管总成检验规范

本标准规定了液压支架用软管及软管总成的术语和定义、试验系统要求、试验方法、检验规则。 本标准适用于液压支架用软管及软管总成的检验，也适用于煤矿中输送石油基、水基流体的软管及软管总成的检验。 本标准不适用于蓖麻油基和酯基液体的软管及软管总成的检验。

Inspection specifications of hose and hose kit for powered support

MT/T 539-2006 煤矿用电动锚杆钻机

本标准规定了煤矿用电动锚杆钻机（以下简称钻机）的型号与基本参数、要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于煤矿用电动锚杆钻机。

Electrical bolting rotary drill in coal mine

KS E 3113-2006(2011) 刚内容摩擦浮桥

Friction prop

BS EN 1804-3:2006+A1:2010 地下开采矿机械.液压矿顶支撑物的安全性要求.液压控制系统

This document specifies the safety requirements for hydraulic control devices, including hydraulic valves and their control elements, valve combinations, control systems, pipes and hose assemblies, fittings, shut-off devices, measuring devices, filters, built-in pressure limiting and check valves in legs and rams and water spraying and dust suppression valves when used as specified by the manufacturer or his authorized representative. Excluded are electronic control devices, pressure generators, and internal valves of legs and rams (e.g. constant yield valves, see EN1804-2). Some components are dealt with in other parts of this standard. This document applies to hydraulic control devices at ambient temperatures from –10 °C to 60 °C. This document identifies and takes into account: ? possible hazards which may be caused by the operation of hydraulic control devices; ? areas and operating conditions which may create such hazards; ? hazardous situations which may cause injury or may be damaging to health; ? hazards which may be caused by firedamp and/or combustible dusts. This document describes methods for the reduction of these hazards. A list of significant hazards covered appears in clause 4. This document is applicable to all hydraulic control devices placed on the market for the first time after the date of issue of this standard. This document does not specify any additional requirements for: ? use in particularly corrosive environments; ? hazards occurring during construction, transportation, decommissioning; ? earthquakes.

Machines for underground mines - Safety requirements for hydraulic powered roof supports - Hydraulic control systems

BS EN 1804-3:2006 地矿机械.液压矿顶支撑物的安全要求.液压控制系统

This document specifies the safety requirements for hydraulic control devices, including hydraulic valves and their control elements, valve combinations, control systems, pipes and hose assemblies, fittings, shut-off devices, measuring devices, filters, built-in pressure limiting and check valves in legs and rams and water spraying and dust suppression valves when used as specified by the manufacturer or his authorized representative. Excluded are electronic control devices, pressure generators, and internal valves of legs and rams (e.g. constant yield valves, see EN1804-2). Some components are dealt with in other parts of this standard. NOTE prEN1804-4 also applies to electro-hydraulic control devices. Part 4 also contains requirements for electrical control elements of valves. This document applies to hydraulic control devices at ambient temperatures from –10 °C to 60 °C. This document identifies and takes into account: - possible hazards which may be caused by the operation of hydraulic control devices; - areas and operating conditions which may create such hazards; - hazardous situations which may cause injury or may be damaging to health; - hazards which may be caused by firedamp and/or combustible dusts. This document describes methods for the reduction of these hazards. A list of significant hazards covered appears in clause 4. This document is applicable to all hydraulic control devices placed on the market for the first time after the date of issue of this standard. This document does not specify any additional requirements for: - use in particularly corrosive environments; - hazards occurring during construction, transportation, decommissioning; - earthquakes.

Machines for underground mines - Safety requirements for hydraulic powered roof supports - Hydraulic control systems

EN 1804-3:2006 煤矿机械.液力顶支护的安全要求.第3部分:液压控制系统.包含修改件A1-2010

This document specifies the safety requirements for hydraulic control devices, including hydraulic valves and their control elements, valve combinations, control systems, pipes and hose assemblies, fittings, shut-off devices, measuring devices, filters, built-in pressure limiting and check valves in legs and rams and water spraying and dust suppression valves when used as specified by the manufacturer or his authorized representative. Excluded are electronic control devices, pressure generators, and internal valves of legs and rams (e. g. constant yield valves, see EN1804-2). Some components are dealt with in other parts of this standard. NOTE prEN1804-4 also applies to electro-hydraulic control devices. Part 4 also contains requirements for electrical control elements of valves.This document applies to hydraulic control devices at ambient temperatures from-10 ℃ to 60 ℃.This document identifies and takes into account: possible hazards which may be caused by the operation of hydraulic control devices; areas and operating conditions which may create such hazards; hazardous situations which may cause injury or may be damaging to health; hazards which may be caused by firedamp and/or combustible dusts.This document describes methods for the reduction of these hazards. A list of significant hazards covered appears in clause 4.This document is applicable to all hydraulic control devices placed on the market for the first time after the date of issue of this standard.This document does not specify any additional requirements for: use in particularly corrosive environments; hazards occurring during construction, transportation, decommissioning; earthquakes.

Machines for underground mines - Safety requirements for hydraulic powered roof supports - Part 3: Hydraulic control systems (Incorporates Amendment A1: 2010)

MT/T 979-2006 煤矿用锚杆拉力计

本标准规定了煤矿用锚杆拉力计（以下简称拉力计）的型式与基本参数、技术要求、试验方法、检验规则、标志、包装、运输及贮存。 本标准适用于煤矿用锚杆拉力计，也适用于非煤矿用锚杆拉力计。

Anchor shank tension apparatus in coal mine

MT/T 971-2005 悬臂式掘进机　电气控制设备

本标准规定了煤矿用悬臂式掘进机电气控制设备（以下简称电控设备）的形式与参数、要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于在含有瓦斯（甲烷）和粉尘爆炸危险的矿井中，作为开拓准备工作面悬臂式掘进机的控制设备。

Boom-type roadheader--Electric control equipment

MT/T 154.3-2005 刨煤机产品型号编制方法

本标准规定了刨煤机产品型号的组成和排列、产品型号各组成代号的规定、产品型号示例和产品型号管理办法。 本标准适用于煤矿地下开采采煤工作面用刨煤机的产品型号编制。

Model designation of plough

MT/T 942-2005 矿用锚索

本标准规定了矿用锚索的分类与型号、技术要求、试验方法、检验规则以及标志、包装、运输与贮存。 本标准适用于煤矿井巷工程支护用预应力锚索。

Prestressed anchorage in coal mine

MT/T 321-2004 采煤机螺旋滚筒

本标准规定了采煤机螺旋滚筒的术语和定义、分类和型号命名、要求、试验方法、检验规则、标志、包装与运输。 本标准适用于煤矿地下开采用的采煤机螺旋滚筒(以下简称“滚筒”)。

Helical drum for shearers

MT/T 928-2004 悬臂式掘进机.圆环刮板链及驱动链轮的系列与参数

本标准规定了悬臂式掘进机用圆环刮板链(以下简称刮板链)及驱动链轮(以下简称链轮)的型式和参数系列。 本标准适用于煤矿井下用悬臂式掘进机，也适用于装煤机及连续采煤机等其他煤矿机械用圆环刮板链和链轮。

Boom-type roadheader-Series and parameters of scraper round link chain and driving sprocket