75.100 润滑剂、工业油及相关产品 标准查询与下载

ASTM D1662-24 切削油中活性硫的标准试验方法

Standard Test Method for Active Sulfur in Cutting Oils

BS ISO 8068:2024 润滑油、工业用油及相关产品（L 级） T 系列（涡轮机） 涡轮机润滑油规范

Lubricants, industrial oils and related products (class L). Family T (Turbines). Specifications for lubricating oils for turbines

24/30472120 DC ISO 20120 草案润滑剂 手动变速箱油润滑同步器摩擦系数的测定 (MTF) 高频线性振荡 (SRV) 试验机

Draft ISO 20120 Lubricants — Determination of the Coefficient of Friction of Synchronizer Lubricated by Manual Transmission Fluids (MTF) — High-Frequency, Linear-Oscillation (SRV) Test Machine

GSO ASTM D5453:2024 用紫外荧光法测定轻质烃、火花点火发动机燃料、柴油发动机燃料和发动机油中总硫含量的标准试验方法

1.1 This test method covers the determination of total sulfur in liquid hydrocarbons, boiling in the range from approximately 25 °C to 400 °C, with viscosities between approximately 0.2 cSt and 20 cSt (mm2 /s) at room temperature. 1.2 Three separate interlaboratory studies (ILS) on precision, and three other investigations that resulted in an ASTM research report, have determined that this test method is applicable to naphthas, distillates, engine oil, ethanol, Fatty Acid Methyl Ester (FAME), and engine fuel such as gasoline, oxygen enriched gasoline (ethanol blends, E-85, M-85, RFG), diesel, biodiesel, diesel/biodiesel blends, and jet fuel. Samples containing 1.0 mg ⁄kg to 8000 mg ⁄kg total sulfur can be analyzed (Note 1). NOTE 1—Estimates of the pooled limit of quantification (PLOQ) for the precision studies were calculated. Values ranged between less than 1.0 mg ⁄kg and less than 5.0 mg ⁄kg (see Section 9 and 16.1). 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For warning statements, see 3.1, 7.3, 7.4, Section 8, and 9.1. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence

GSO ASTM D6792:2024 石油产品、液体燃料和润滑剂检测实验室质量管理体系标准规范

1.1 This practice covers the establishment and maintenance of the essentials of a quality management system in laboratories engaged in the analysis of petroleum products, liquid fuels, and lubricants. It is designed to be used in conjunction with Practice D6299. NOTE 1—This practice is based on the quality management concepts and principles advocated in ANSI/ISO/ASQ Q9000 standards, ISO/IEC 17025, ASQ Manual,2 and ASTM standards such as D3244, D4182, D4621, D6299, D6300, D7372, E29, E177, E456, E548, E882, E994, E1301, E1323, STP 15D,3 and STP 1209.4 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory requirements prior to use. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Quality Management Systems in Petroleum Products, Liquid Fuels, and Lubricants Testing Laboratories

GSO ASTM D5133:2024 使用温度扫描技术对润滑油的低温、低剪切速率、粘度/温度依赖性进行的标准试验方法

1.1 This test method covers the measurement of the apparent viscosity of engine oil at low temperatures. 1.2 A shear rate of approximately 0.2 s-1 is produced at shear stresses below 100 Pa. Apparent viscosity is measured continuously as the sample is cooled at a rate of 1 °C ⁄h over the range −5 °C to −40 °C, or to the temperature at which the viscosity exceeds 40 000 mPa·s (cP). 1.3 The measurements resulting from this test method are viscosity, the maximum rate of viscosity increase (Gelation Index), and the temperature at which the Gelation Index occurs. 1.4 Applicability to petroleum products other than engine oils has not been determined in preparing this test method. 1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Low Temperature, Low Shear Rate, Viscosity/Temperature Dependence of Lubricating Oils Using a Temperature-Scanning Technique

GSO ASTM D5763:2024 使用通用玻璃器皿对齿轮油氧化和热稳定性特性的标准试验方法

1.1 This test method covers the determination of the oxidation characteristics of extreme pressure and non-extreme pressure gear oils and includes the quantitative determination of total sludge, viscosity change, and oil loss. NOTE 1—While the round-robin tests used ISO VG 220 extreme pressure gear oils for developing precision data, the test method can be extended to other viscosity grades and to non-extreme pressure gear oils. Refer to Classification D2422 for viscosity grades. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Oxidation and Thermal Stability Characteristics of Gear Oils Using Universal Glassware

T/YJC 016-2024 油膜轴承油制备技术规范

1.原材料:选择优质的基础油和添加剂，确保原材料的质量稳定可靠。同时，应对原材料进行严格的质量检验，包括外观、密度、粘度、闪点等指标的检测，以确保其符合生产要求。 2.生产工艺:制定科学合理的生产工艺流程，明确各个生产环节的操作规范和质量控制要求。生产过程中应严格控制温度、压力、搅拌速度等参数，确保油膜轴承油的各项性能指标达到标准要求。 3.产品的检验和测试:建立完善的检验和测试体系，对生产出的油膜轴承油进行全面的质量评估。包括粘度指数、油水分离性、氧化安定性、金属腐蚀、闪点、承载能力等关键指标的测试，以确保产品质量的稳定性和可靠性。 4.质量追溯和持续改进:建立完善的质量追溯体系，对生产过程中的每一个环节进行记录和追溯。同时，应定期对生产过程和产品质量进行审查和分析，及时发现问题并采取改进措施，不断提高油膜轴承油制备技术的水平和质量。

Technical specifications for oil film bearing oil preparation

24/30486996 DC BS EN ISO 13503-2 石油和天然气工业 包括低碳能源 完井液和材料 第2部分：水力压裂和砾石充填作业中使用的支撑剂性能的测量

BS EN ISO 13503-2 Oil and gas industries including lower carbon energy - Completion fluids and materials - Part 2: Measurement of properties of proppants used in hydraulic fracturing and gravel-packing operations

T/QGCML 3976-2024 废矿物油（废轧制油）再生润滑油

本文件规定了废矿物油（废轧制油）再生润滑油的技术要求、试验方法、检验规则、标志、包装、运输、贮存、保质期。 本文件适用于以工业废油为原料生产的废矿物油（废轧制油）再生润滑油。

Waste mineral oil (waste rolling oil) regenerated lubricating oil

ASTM D8112-24 获取涡轮运行相关润滑液在役样品的标准指南

1.1  This guide is applicable for collecting representative fluid samples for the effective condition monitoring of steam and gas turbine lubrication and generator cooling gas sealing systems in the power generation industry. In addition, this guide is also applicable for collecting representative samples from power generation auxiliary equipment including hydraulic systems. 1.2  The fluid may be used for lubrication of turbine-generator bearings and gears, for sealing generator cooling gas as well as a hydraulic fluid for the control system. The fluid is typically supplied by dedicated pumps to different points in the system from a common or separate reservoirs. Some large steam turbine lubrication systems may also have a separate high pressure pump to allow generation of a hydrostatic fluid film for the most heavily loaded bearings prior to rotation. For some components, the lubricating fluid may be provided in the form of splashing formed by the system components moving through fluid surfaces at atmospheric pressure. 1.3  Turbine lubrication and hydraulic systems are primarily lubricated with petroleum based fluids but occasionally also use synthetic fluids. 1.4  For large lubrication and hydraulic turbine systems, it may be beneficial to extract multiple samples from different locations for determining the condition of a specific component. 1.5  The values stated in SI units are regarded as standard. 1.5.1  The values given in parentheses are for information only. 1.6  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7  This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Obtaining In-Service Samples of Turbine Operation Related Lubricating Fluid

ASTM D8206-24 润滑脂氧化稳定性的标准试验方法——小规模快速氧化试验（RSSOT）

Standard Test Method for Oxidation Stability of Lubricating Greases—Rapid Small-Scale Oxidation Test (RSSOT)

ASTM D4042-24 轧钢厂轧制油中灰分和全铁分散的取样和试验的标准试验方法

Standard Test Method for Sampling and Testing for Ash and Total Iron in Steel Mill Dispersions of Rolling Oils

ASTM D2007-19(2024)e1 通过粘土凝胶吸附色谱法在橡胶延伸剂和加工油及其他石油衍生油中的特征组的标准试验方法

Standard Test Method for Characteristic Groups in Rubber Extender and Processing Oils and Other Petroleum-Derived Oils by the Clay-Gel Absorption Chromatographic Method

ASTM D7156-24 T-11废气再循环柴油机中柴油机油评定的标准试验方法

Standard Test Method for Evaluation of Diesel Engine Oils in the T-11 Exhaust Gas Recirculation Diesel Engine

ASTM D7452-24 高速和冲击载荷条件下最终传动轴用润滑剂承载性能评定的标准试验方法

Standard Test Method for Evaluation of the Load Carrying Properties of Lubricants Used for Final Drive Axles, Under Conditions of High Speed and Shock Loading

ASTM D6709-24 序列VIII火花点火式发动机（CLR油试验发动机）中汽车发动机油评价的标准试验方法

Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence VIII Spark-Ignition Engine (CLR Oil Test Engine)

ASTM D8048-24 T-13柴油机中柴油机油评定的标准试验方法

Standard Test Method for Evaluation of Diesel Engine Oils in T-13 Diesel Engine

ASTM D5306-24 润滑油和液压流体线性火焰传播速率的标准试验方法

Standard Test Method for Linear Flame Propagation Rate of Lubricating Oils and Hydraulic Fluids

ASTM D8350-24 IVB顺序火花点火式发动机中汽车发动机油评定的标准试验方法

Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IVB Spark-Ignition Engine