77.040.99 金属材料的其他试验方法 标准查询与下载

KS D ISO 2626:2013 铜 氢脆试验

Copper－Hydrogen embrittlement test

KS D ISO 4746:2013 无氧铜 铜屑黏合力试验

Oxygen-free copper－Scale adhesion test

ISO 4967:2013 钢.非金属包含物含量测定.利用标准图表的显微照相法

This International Standards pecifies a micrographic method of determining the non-metallicinclusions in rolled or forged steel products having a reduction ratio of at least 3 using standard diagrams. This method is widely used to assess the suitability of a steel for a given use. However, since it is difficult to achieve reproducible re suits owing to the influence of the test operator, even with a large number of specimens, precautions should be taken when using the method.

Steel.Determination of content of non-metallic inclusions.Micrographic method using standard diagrams

DIN EN ISO 643:2013 钢.表观粒度的显微照相测定法(ISO 643-2012).德文版本EN ISO 643-2012

Steels - Micrographic determination of the apparent grain size (ISO 643:2012); German version EN ISO 643:2012

LST EN ISO 643:2013 钢 表观晶粒尺寸的显微照片测定（ISO 643:2012）

Steels - Micrographic determination of the apparent grain size (ISO 643:2012)

YB/T 4340-2013 连铸钢方坯低倍枝晶组织缺陷评级图

本标准规定了连铸钢方坯低倍枝晶组织缺陷评级的取样、试样腐蚀方法、缺陷分类、评定及检验报告。本标准适用于连铸工艺生产的边长不大于600mm的碳素钢、低合金钢、合金结构钢等方坯低倍枝晶组织缺陷评级。矩形坯、圆坯及异型坯也可参照使用。

Standard diagrams for macrostructure dendritic and defect in continuous casting blank

YS/T 864-2013 铜及铜合金板带箔材表面清洁度检验方法

本标准规定了铜及铜合金板带箔材表面清洁度的测定方法、本标准适用于铜及铜合金板带箔材表面清洁度的测定及脱脂前后板带箔材洗净率的测定,以判定清洗剂对铜板带箔材的清洗效果及成品带材表面的洁净程度、

Method of slab band tinsel surface cleanliness analysis of copper and copper alloys

YB/T 4339-2013 连铸钢板坯低倍枝晶组织缺陷评级图

本标准规定了连铸钢板坯低倍枝晶组织缺陷评级的取样和试样腐蚀方法、缺陷分类、评定及检验报告。本标准适用于连铸工艺生产的厚度不大于300mm的碳素钢、低合金钢、合金钢结构钢板坯低倍枝晶组织缺陷评级。

Standard diagrams for dendritic-macrostructure and defect in continuous casting slab

YB/T 4002-2013 连铸钢方坯低倍组织缺陷评级图

本标准规定了连铸钢方坯低倍组织和缺陷形貌特征、产生原因和评定原则。本标准适用于评定采用连铸工艺生产的碳素钢及低合金钢等方坯横截面酸蚀低倍组织缺陷。方坯横截面尺寸范围为边长90mm~400mm,矩形坯也可参照使用。

Standard diagrams for macrostructure and defects in continuous casting billets

NF A04-102:2013 钢 - 表观晶粒度的显微照相测定

Steels - Micrographic determination of the apparent grain size

GSO ISO 4746:2013 无氧铜 测量测试台

This International Standard specifies a procedure for the scale adhesion testing of Oxygen-free high-conductivity topper.

Oxygen-free copper -- Scale adhesion test

BS EN ISO 643:2012 钢. 表观晶粒度的显微照相测定

Steels. Micrographic determination of the apparent grain size

ISO 643:2012 钢.表面粒度的缩微照相测定

This International Standard specifies a micrographic method of determining apparent ferritic or austenitic grain Size in steels. It describes the methods of revealing grain boundaries and of estimating the mean grain size of specimens with unimodal size distribution. Although grains are three-dimensional in shape, the metallographic Sectioning plane can cut through a grain at any point from a grain cornem to the maximum diameter of the grain, thus producing a range of apparent grain sizes on the two-dimensional plane, even in a sample with a perfectly consistent grain size.

Steels - Micrographic determination of the apparent grain size

YB/T 4293-2012 双管直流磁性能测量方法

本标准规定了磁轭钢等铁基软磁材料直流磁感应强度的测量原理及线路、试样、测量装置、测量步骤、结果计算、不确定度、报告等。本标准适用于磁轭钢以及各种铁基软磁材料的直流磁感应强度B等磁性参数的测量。本测试方法适用的磁场范围为300A/m~30000A/m;测量环境温度为23℃±5℃,相对湿度小于80%。

Method of measurement of d. c. magnetic properties of double solenoid

YB/T 4292-2012 电工钢带（片）几何特性测试方法

本标准规定了电工钢带(片)几何特性的术语及定义、测试方法、测试报告等。本标准适用于电工钢带(片)的不平度、残余曲率、镰刀弯、因内应力引起的剪切边的偏差、剪切毛刺等几何特性的测试。

Methods of determination of the geometrical characteristics of electric steel sheet and strip

YS/T 799-2012 铝板带箔表面清洁度试验方法

本标准规定了铝板带箔表面清洁度(由铝粉引起)的试验方法。 本标准适用于食品箔、药用箔和PS版基等铝及铝合金板、带、箔半成品、产品的表面清洁度测试，也可用于其他铝材。

Test method for the surface cleanes of aluminum and aluminum alloy sheets,strips and foils

DIN EN ISO 643:2012 钢.表观粒度的显微照相测定法(ISO/FDIS 643-2012).德文版本FprEN ISO 643-2012

Steels - Micrographic determination of the apparent grain size (ISO/FDIS 643:2012); German version FprEN ISO 643:2012

EN ISO 643:2012 钢的显微照相的决心明显的晶粒尺寸

This International Standard specifies a micrographic method of determining apparent ferritic or austenitic grain size in steels. It describes the methods of revealing grain boundaries and of estimating the mean grain size of specimens with unimodal size distribution. Although grains are three-dimensional in shape, the metallographic sectioning plane can cut through a grain at any point from a grain corner, to the maximum diameter of the grain, thus producing a range of apparent grain sizes on the two-dimensional plane, even in a sample with a perfectly consistent grain size.

Steels - Micrographic determination of the apparent grain size

DB37/T 1881-2011 金属压力界面声发射连续监测规程

Code for Continuous Monitoring of Acoustic Emission at Metal Pressure Interface

ASTM E562-11 系统人工点计数法体积分数测定的标准试验方法

This test method is based upon the stereological principle that a grid with a number of regularly arrayed points, when systematically placed over an image of a two-dimensional section through the microstructure, can provide, after a representative number of placements on different fields, an unbiased statistical estimation of the volume fraction of an identifiable constituent or phase (1, 2, 3). This test method has been described (4) as being superior to other manual methods with regard to effort, bias, and simplicity. Any number of clearly distinguishable constituents or phases within a microstructure (or macrostructure) can be counted using the method. Thus, the method can be applied to any type of solid material from which adequate two-dimensional sections can be prepared and observed. A condensed step-by-step guide for using the method is given in Annex A1. 1.1 This test method describes a systematic manual point counting procedure for statistically estimating the volume fraction of an identifiable constituent or phase from sections through the microstructure by means of a point grid. 1.2 The use of automatic image analysis to determine the volume fraction of constituents is described in Practice E1245. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Determining Volume Fraction by Systematic Manual Point Count