77.060 金属的腐蚀 标准查询与下载

EN ISO 21207:2022 人工气候下的腐蚀试验.包括交替暴露于腐蚀促进气体、中性盐雾和干燥中的加速腐蚀试验

ISO 21207:2015 defines two accelerated corrosion test methods to be used in assessing the corrosion resistance of products with metals in environments where there is a significant influence of chloride ions, mainly as sodium chloride from a marine source or by winter road de-icing salt, and of corrosion-promoting gases from industrial or traffic air pollution. ISO 21207:2015 specifies both the test apparatus and test procedures to be used in executing the accelerated corrosion tests. The methods are especially suitable for assessing the corrosion resistance of sensitive products with metals, e.g. electronic components, used in traffic and industrial environments.

Corrosion tests in artificial atmospheres - Accelerated corrosion tests involving alternate exposure to corrosion-promoting gases, neutral salt-spray and drying (ISO 21207:2015)

EN ISO 22479:2022 金属和合金的腐蚀.潮湿气氛中的二氧化硫试验（固定气体法）

This document specifies a method for assessing the resistance of materials or products to a humid atmosphere containing sulfur dioxide. This method is applicable to testing metals and alloys, metallic and non-organic coatings and organic coatings.

Corrosion of metals and alloys - Sulfur dioxide test in a humid atmosphere (fixed gas method) (ISO 22479:2019)

ASTM D7376-10a(2022) 线圈涂层金属湿堆贮存条件的室外评估标准实施规程

1.1 This practice is used to determine the resistance to corrosion and blistering of coil-coated metal products relative to one another when stacked outdoors under direct weathering conditions in which they are wetted by rain and dew. 1.2 The coil-coated product variables evaluated may include, but are not limited to, substrates, pretreatments, primers, topcoats, and backers. 1.3 This test simulates a stacked building panel bundle stored at a job site in wet outdoor conditions. The results from panels tested during the same time period at the same physical location may be used to compare products as an indicator of relative field performance. Environments with higher temperature and moisture levels accelerate corrosion and blistering. 1.4 This standard does not endorse the storage of level (that is, 0° from horizontal) building panels stacks in wet outdoor conditions. Level storage of building panels is not recommended and is used in this standard for evaluation only. 1.5 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Outdoor Evaluation of Wet Stack Storage Conditions on Coil-Coated Metals

EN ISO 12696:2022 混凝土中钢的阴极保护

This document specifies performance requirements for cathodic protection of steel in cement-based concrete, in both new and existing structures. It covers building and civil engineering structures, including carbon steel reinforcement and prestressed reinforcement embedded in the concrete. It is applicable to uncoated steel reinforcement and to organic-coated steel reinforcement. It is not applicable to reinforced concrete containing electrically conductive fibres (e.g. carbon or steel). This document applies to steel embedded in atmospherically exposed, buried, immersed and tidal elements of buildings or structures. This document is only applicable to the applications of cathodic protection to steel in concrete which are designed with the intention to, and can be demonstrated to, meet the criteria of protection specified in 8.6. This requires the provision of sufficient performance monitoring systems as specified in 6.3 to all parts of the structure intended to be protected, in order to assess the extent to which the criteria in 8.6 are met. This document does not apply to galvanic anodes or systems applied into patch repairs to reduce the effects of ‘incipient anodes’. This document does also not apply to any form of cathodic protection systems or other electrochemical treatments that either cannot meet the requirements of 8.6 or are not provided with the performance monitoring systems (see 6.3) that are necessary to assess whether the criteria of protection specified in 8.6 are met. NOTE 1 Annex A gives guidance on the principles of cathodic protection and its application to steel in concrete. NOTE 2 This document, while not specifically intended to address cathodic protection of steel in any electrolyte except concrete, can be applied to cathodic protection of steel in other cementitious materials such as are found, for example, in early 20th century steel-framed masonry, brick and terracotta clad buildings. In such applications, additional considerations specific to these structures are required in respect of design, materials and installation of cathodic protection; however, the requirements of this document can be applied to these systems.

Cathodic protection of steel in concrete (ISO 12696:2022)

ISO 24656:2022 海上风电结构的阴极保护

This document specifies the requirements for the external and internal cathodic protection for offshore wind farm s tructures. It is applicable for structures and appurtenances in contact with seawater or seabed environments . This document addresses: — design and implementation of cathodic protection s ystems for new s teel s tructures; — assessment of residual life of exis ting cathodic protection s ystems; — design and implementation ofretrofit cathodic protection s ystems for improvement ofthe protection level or for life extension of the protection; — inspection and performance monitoring of cathodic protection s ys tems installed on existing s tructures, and — guidance on cathodic protection of reinforced concrete s tructures .

Cathodic protection of offshore wind structures

ASTM D1748-22 湿度箱中金属防腐剂防锈的标准试验方法

1.1 This test method covers the evaluation of the rustpreventive properties of metal preservatives under conditions of high humidity. 1.2 The values stated in SI units are to be regarded as the standard except where the test apparatus or consumable parts are only available in other units. In such cases these will be regarded as standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to consult and establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Rust Protection by Metal Preservatives in the Humidity Cabinet

ASTM G30-22 U形弯曲应力腐蚀试样的制作和使用标准实施规程

1.1 This practice covers procedures for making and using U-bend specimens for the evaluation of stress-corrosion cracking in metals. The U-bend specimen is generally a rectangular strip that is bent 180° around a predetermined radius and maintained in this constant strain condition during the stresscorrosion test. Bends slightly less than or greater than 180° are sometimes used. Typical U-bend configurations showing several different methods of maintaining the applied stress are shown in Fig. 1. 1.2 U-bend specimens usually contain both elastic and plastic strain. In some cases (for example, very thin sheet or small diameter wire) it is possible to form a U-bend and produce only elastic strain. However, bent-beam (Practice G39 or direct tension (Practice G49)) specimens are normally used to study stress-corrosion cracking of strip or sheet under elastic strain only. 1.3 This practice is concerned only with the test specimen and not the environmental aspects of stress-corrosion testing, which are discussed elsewhere (1)2 and in Practices G35, G36, G37, G41, G44, G103 and Test Method G123. 1.4 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Making and Using U-Bend Stress-Corrosion Test Specimens

ASTM D3316-06(2022) 含铜的全氯乙烯稳定性的标准试验方法

1.1 This test method covers the evaluation of the corrosiveness to copper metal by perchloroethylene. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Stability of Perchloroethylene with Copper

ASTM G94-22 氧气设备用金属评估的标准指南

1.1 This guide applies to metallic materials under consideration for oxygen or oxygen-enriched fluid service, direct or indirect, as defined in Section 3. It is concerned primarily with the properties of a metallic material associated with its relative susceptibility to ignition and propagation of combustion. It does not involve mechanical properties, potential toxicity, outgassing, reactions between various materials in the system, functional reliability, or performance characteristics such as aging, shredding, or sloughing of particles, except when these might contribute to an ignition. 1.2 This document applies only to metals; nonmetals are covered in Guide G63. NOTE 1—The American Society for Testing and Materials takes no position respecting the validity of any evaluation methods asserted in connection with any item mentioned in this guide. Users of this guide are expressly advised that determination of the validity of any such evaluation methods and data and the risk of use of such evaluation methods and data are entirely their own responsibility. NOTE 2—In evaluating materials, any mixture with oxygen exceeding atmospheric concentration at pressures higher than atmospheric should be evaluated from the hazard point of view for possible significant increase in material combustibility. 1.3 Units—The values stated in SI units are to be regarded as the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Evaluating Metals for Oxygen Service

BS ISO 24020:2022 金属和合金的腐蚀 狭缝喷射金属材料无颗粒侵蚀腐蚀的标准试验方法

1   Scope This document specifies a test method for particle-free erosion corrosion of metallic materials by use of jet-in-slit which is flow induced corrosion in single phase flowing liquids. The test method can be used for ranking materials performance, selecting candidate materials and testing the effects of corrosion inhibitors.

Corrosion of metals and alloys. Standard test method for particle-free erosion corrosion of metallic materials by jet-in-slit

ASTM B810-01a(2022) 通过铜片质量变化校准大气腐蚀试验室的标准试验方法

1.1 This test method covers the calibration of atmospheric corrosion test chambers for electrical contacts that produce an adherent film of corrosion product on copper, such as a test comprised of a mixture of flowing gases that react with copper. 1.2 This test method is not applicable to tests where corrosion products may be removed from a copper surface during the test by fluids. 1.3 This test method is not applicable to tests where airborne solid or liquid material may be deposited on a copper surface during the test, as in a test which includes particulates suspended in the atmosphere. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Calibration of Atmospheric Corrosion Test Chambers by Change in Mass of Copper Coupons

BS ISO 23721:2022 金属和合金的腐蚀 不锈钢大气腐蚀锈迹和污点外观评定方法

1   Scope This document specifies a method for evaluating the aesthetic appearance of stainless steels qualitatively by rating rust and stains formed by atmospheric corrosion. The rust and stains on stainless steels formed by atmospheric corrosion are rated by using 10 photographic standards. This method is especially suitable for evaluating the appearance of specimens and structures made of stainless steels under atmosphere exposure.

Corrosion of metals and alloys. Rating method by appearance of rust and stains of atmospheric corrosion for stainless steels

ISO/TR 7655:2022 金属和合金的腐蚀.使用消毒剂时的金属腐蚀防护概述

Corrosion of metals and alloys — Overview of metal corrosion protection when using disinfectants

ISO 23721:2022 金属和合金的腐蚀.不锈钢大气腐蚀锈渍外观评级法

This document specifies a method for evaluating the aesthetic appearance of stainless steels qualitatively by rating rust and stains formed by atmospheric corrosion. The rust and stains on stainless steels formed by atmospheric corrosion are rated by using 10 photographic standards. This method is especially suitable for evaluating the appearance of specimens and structures made of stainless steels under atmosphere exposure.

Corrosion of metals and alloys — Rating method by appearance of rust and stains of atmospheric corrosion for stainless steels

ISO/CD 16674:2022 输变电系统腐蚀控制工程生命周期通用要求

Corrosion control engineering life cycle of power transmission and transformation system-General requirement

ISO 24020:2022 金属和合金的腐蚀.用狭缝喷射法测定金属材料无颗粒侵蚀腐蚀的标准试验方法

This document specifies a test method for particle-free erosion corrosion of metallic materials by use of jet-in-slit which is flow induced corrosion in single phase flowing liquids. The test method can be used for ranking materials performance, selecting candidate materials and testing the effects of corrosion inhibitors.

Corrosion of metals and alloys — Standard test method for particle-free erosion corrosion of metallic materials by jet-in-slit

ISO 9227:2022 人造大气中的腐蚀试验 - 盐雾试验

This document specifies the apparatus, the reagents and the procedure to be used in conducting the neutral salt spray (NSS), acetic acid salt spray (AASS) and copper-accelerated acetic acid salt spray (CASS) tests for assessment of the corrosion resistance of metallic materials, with or without permanent or temporary corrosion protection. It also describes the method employed to evaluate the corrosivity of the test cabinet environment. It does not specify the dimensions or types of test specimens, the exposure period to be used for a particular product, or the interpretation of results. Such details are provided in the appropriate product specifications. The salt spray tests are particularly useful for detecting discontinuities, such as pores and other defects, in certain metallic, organic, anodic oxide and conversion coatings. The NSS test is particularly applicable to: — metals and their alloys; — metallic coatings (anodic and cathodic); — conversion coatings; — anodic oxide coatings; — organic coatings on metallic materials. The AASS test is especially useful for testing decorative coatings of copper + nickel + chromium, or nickel + chromium. It has also been found suitable for testing anodic and organic coatings on aluminium. The CASS test is useful for testing decorative coatings of copper + nickel + chromium, or nickel + chromium. It has also been found suitable for testing anodic and organic coatings on aluminium. The salt spray methods are all suitable for checking that the quality of a metallic material, with or without corrosion protection, is maintained. They are not intended to be used for comparative testing as a means of ranking different materials relative to each other with respect to corrosion resistance or as means of predicting long-term corrosion resistance of the tested material.

Corrosion tests in artificial atmospheres — Salt spray tests

KS H ISO 9233-2021 干酪和干酪皮.纳他霉素含量的测定.分子吸收光谱法和高效液相色谱法

Cheese and cheese rind — Determination of natamycin content —Method by molecular absorption spectrometry and by high-performance liquid chromatography

KS H ISO 9233:2021 干酪和干酪皮.纳他霉素含量的测定.分子吸收光谱法和高效液相色谱法

Cheese and cheese rind — Determination of natamycin content —Method by molecular absorption spectrometry and by high-performance liquid chromatography

KS D ISO 22910-2021 金属和合金的腐蚀.通过添加剂制造方法制造的钛合金电化学临界局部腐蚀温度（E-CLCT）的测量

Corrosion of metals and alloys — Measurement of the electrochemical critical localized corrosion temperature(E-CLCT) for Ti alloys fabricated via the additive manufacturing method