77.060 金属的腐蚀 标准查询与下载

KS D ISO 7539-8-2020 金属和合金的腐蚀 - 应力腐蚀试验 - 第8部分:样品的制备和使用评估焊接

Corrosion of metals and alloys — Stress corrosion testing —Part 8: Preparation and use of specimens to evaluate weldments

KS D ISO 7539-7:2020 金属和合金的腐蚀 - 应力腐蚀试验 - 第7部分:慢应变率试验方法

Corrosion of metals and alloys — Stress corrosion testing —Part 7: Method for slow strain rate testing

KS D ISO 11845-2020 金属和合金的腐蚀.腐蚀试验的一般原则

Corrosion of metals and alloys — General principles for corrosion testing

KS D ISO 7539-7-2020 金属和合金的腐蚀 - 应力腐蚀试验 - 第7部分:慢应变率试验方法

Corrosion of metals and alloys — Stress corrosion testing —Part 7: Method for slow strain rate testing

KS D 8329-2020 镁合金防蚀处理法

Processes for corrosion protection of magnesium alloys

KS D 4325-2020 受保护金属户外暴露试验

Outdoor exposure test for protected metals

KS D ISO 7539-1-2020 金属和合金的腐蚀 - 应力腐蚀测试 - 第1部分:测试程序的一般指导

Corrosion of metals and alloys — Stress corrosion testing — Part 1: General guidance on testing procedures

KS D ISO 11845:2020 金属和合金的腐蚀.腐蚀试验的一般原则

Corrosion of metals and alloys — General principles for corrosion testing

KS D ISO 11303:2020 金属和合金的腐蚀 - 选择防止大气腐蚀的方法指南

Corrosion of metals and alloys — Guidelines for selection of protection methods against atmospheric corrosion

KS D ISO 7539-8:2020 金属和合金的腐蚀 - 应力腐蚀试验 - 第8部分:样品的制备和使用评估焊接

Corrosion of metals and alloys — Stress corrosion testing —Part 8: Preparation and use of specimens to evaluate weldments

PN-EN ISO 11844-2-2020-12 E 金属和合金的腐蚀 室内大气低腐蚀性分类 第2部分：室内大气腐蚀侵蚀的测定（ISO 11844-2:2020）

Corrosion of metals and alloys -- Classification of low corrosivity of indoor atmospheres -- Part 2: Determination of corrosion attack in indoor atmospheres (ISO 11844-2:2020)

PN-EN ISO 11844-1-2020-12 E 金属和合金的腐蚀 室内大气低腐蚀性分类 第1部分：室内腐蚀性的测定和估算（ISO 11844-1:2020）

Corrosion of metals and alloys -- Classification of low corrosivity of indoor atmospheres -- Part 1: Determination and estimation of indoor corrosivity (ISO 11844-1:2020)

KS W 1128-2020 可硬化不锈钢零件的航空表面处理

AEROSPACE-SURFACE TREATMENT OF HARDENABLE STAINLESS STEEL PARTS

OENORM EN ISO 11463:2020 金属和合金的腐蚀 点腐蚀评估指南（ISO 11463:2020）

Corrosion of metals and alloys - Guidelines for the evaluation of pitting corrosion (ISO 11463:2020)

LST EN ISO 11463:2020 金属和合金的腐蚀 点腐蚀评估指南（ISO 11463:2020）

Corrosion of metals and alloys - Guidelines for the evaluation of pitting corrosion (ISO 11463:2020)

DS/ISO 23226:2020 金属和合金的腐蚀 暴露在深海水中的金属和合金的腐蚀试验指南

Corrosion of metals and alloys – Guidelines for the corrosion testing of metals and alloys exposed in deep-sea water

PN-EN ISO 7539-10-2020-11 E 金属和合金的腐蚀 应力腐蚀试验 第10部分：反向 U 型弯曲法（ISO 7539-10:2020）

Corrosion of metals and alloys -- Stress corrosion testing -- Part 10: Reverse U-bend method (ISO 7539-10:2020)

DS/ISO 23449:2020 金属和合金的腐蚀 用于腐蚀测量的多电极阵列

Corrosion of metals and alloys – Multielectrode arrays for corrosion measurement

ASTM G52-20 表面海水中金属和合金的暴露和评估标准实践

1.1 This practice covers conditions for the exposure of metals, alloys, and other materials in natural surface seawater such as those typically found in bays, harbors, channels, and so forth,2 as contrasted with deep ocean testing.3 This practice covers full immersion, tidal zone and related splash, and spray zone exposures.2,4 1.2 This practice sets forth general procedures that should be followed in conducting seawater exposure tests so that meaningful comparisons may be made from one location to another. 1.3 This practice identifies recommended procedures for evaluating the effects of natural surface seawater on the materials exposed. 1.4 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Exposing and Evaluating Metals and Alloys in Surface Seawater

ASTM G199-09(2020)e1 电化学噪声测量标准指南

1.1 This guide covers the procedure for conducting online corrosion monitoring of metals by the use of the electrochemical noise technique. Within the limitations described, this technique can be used to detect localized corrosion activity and to estimate corrosion rate on a continuous basis without removal of the monitoring probes from the plant or experimental cell. 1.2 This guide presents briefly some generally accepted methods of analyses that are useful in the interpretation of corrosion test results. 1.3 This guide does not cover detailed calculations and methods; rather it covers a range of approaches that have found application in corrosion testing. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Electrochemical Noise Measurement