77.060 金属的腐蚀 标准查询与下载
共找到 1478 条与 金属的腐蚀 相关的标准，共 99 页
What is BS EN ISO 11844 ‑ 3 about ? ISO 11844-3 is the third part of the ISO 11844 series of documents on corrosion of metals and alloys. ISO 11844-3 is an international standard on corrosion of metals and alloys that assists you in measuring the environmental parameters affecting indoor corrosivity. ISO 11844 ‑ 3 parameters include humidity and temperature parameters, airborne gas contaminants, airborne particle contaminants.
Corrosion of metals and alloys. Classification of low corrosivity of indoor atmospheres - Measurement of environmental parameters affecting indoor corrosivity
- ICS
- 77.060
- CCS
- 发布
- 2020-02-29
- 实施
- 2020-02-29
This document specifies requirements for the design, installation, positioning, sizing, use and maintenance of coupons for the assessment of the effectiveness of cathodic protection (CP) of buried and immersed metallic structures, such as pipelines, in the case of normal operation as well as AC and DC interference conditions.
Assessment of the effectiveness of cathodic protection based on coupon measurements
- ICS
- 77.060
- CCS
- 发布
- 2020-02-10
- 实施
This document specifies methods for measuring the environmental parameters used to classify the corrosivity of indoor atmospheres on metals and alloys.
Corrosion of metals and alloys - Classification of low corrosivity of indoor atmospheres - Part 3: Measurement of environmental parameters affecting indoor corrosivity (ISO 11844-3:2020)
- ICS
- 77.060
- CCS
- 发布
- 2020-01-29
- 实施
- 2020-04-30
This document specifies methods for measuring the environmental parameters used to classify the corrosivity of indoor atmospheres on metals and alloys.
Corrosion of metals and alloys — Classification of low corrosivity of indoor atmospheres — Part 3: Measurement of environmental parameters affecting indoor corrosivity
- ICS
- 77.060
- CCS
- 发布
- 2020-01-07
- 实施
Passivation treatments for corrosion-resisting steel of aerospace use
- ICS
- 77.060
- CCS
- 发布
- 20191231
- 实施
- 20191231
本标准规定了金属表面清理的方法及技术规范。 本标准适用于通过阴极等离子电解表面处理工艺清理任何金属材料表面存留的一般污染、氧化物、油脂、污垢、腐蚀产物及以表面污染形式存在的外来物。
Cathode plasma electrolytic surface preparation— Technical specification for metal surface cleaning
- ICS
- 77.060
- CCS
- M731
- 发布
- 2019-12-20
- 实施
- 2020-09-21
数据准确可靠是腐蚀检测体系中的基本要求，包括源数据、元数据和所有后续转换、传输的数据。现代电子、通讯以及互联网技术越来越多地应用于腐蚀检监测，腐蚀传感器数据、采集器与传输数据的可靠性，对监测质量和评估结论有重大影响。 制定本标准的目的是：对腐蚀传感器数据、硬件采集器数据及数据传输可靠性的验证进行规范。 制定原则：本标准吸取了相关标准和国内外腐蚀检测领域的科研成果与实践经验，符合腐蚀大数据规则，先进性与广泛性有机结合。
Corrosion monitoring data reliability verification specification
- ICS
- 77.060
- CCS
- M748
- 发布
- 2019-12-20
- 实施
- 2019-12-23
本标准规定了金属表面沉积金属涂层的方法及技术规范。 本标准适用于通过阴极等离子电解表面处理工艺在导电性金属材料表面沉积单组元金属或合金涂层。
Cathode plasma electrolytic surface preparation— Technical specification for deposition of metallic coatings
- ICS
- 77.060
- CCS
- M731
- 发布
- 2019-12-20
- 实施
- 2020-09-21
This document specifies protection criteria for determining the AC corrosion risk of cathodically protected pipelines. It is applicable to buried cathodically protected pipelines that are influenced by AC traction systems and/or AC power lines. In the presence of AC interference, the protection criteria given in ISO 15589-1 are not sufficient to demonstrate that the steel is being protected against corrosion. This document provides limits, measurement procedures, mitigation measures, and information to deal with long-term AC interference for AC voltages at frequencies between 16,7 Hz and 60 Hz and the evaluation of AC corrosion likelihood. This document deals with the possibility of AC corrosion of metallic pipelines due to AC interferences caused by conductive, inductive or capacitive coupling with AC power systems and the maximum tolerable limits of these interference effects. It takes into account the fact that this is a long-term effect, which occurs during normal operating conditions of the AC power system. This document does not cover the safety issues associated with AC voltages on pipelines. These are covered in national standards and regulations (see, e.g., EN 50443).
Corrosion of metals and alloys — Determination of AC corrosion — Protection criteria
- ICS
- 77.060
- CCS
- 发布
- 2019-12-10
- 实施
1.1 This practice covers procedures for designing, preparing, and using ASTM standard tension test specimens for investigating susceptibility to stress-corrosion cracking. Axially loaded specimens may be stressed quantitatively with equipment for application of either a constant load, constant strain, or with a continuously increasing strain. 1.2 Tension test specimens are adaptable for testing a wide variety of product forms as well as parts joined by welding, riveting, or various other methods. 1.3 The exposure of specimens in a corrosive environment is treated only briefly because other standards are being prepared to deal with this aspect. Meanwhile, the investigator is referred to Practices G35, G36, G37, and G44, and to ASTM Special Technical Publication 425 (1).2 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Standard Practice for Preparation and Use of Direct Tension Stress-Corrosion Test Specimens
- ICS
- 77.060
- CCS
- 发布
- 2019-11-01
- 实施
1.1 This practice covers the apparatus, procedure, and conditions required to create and maintain the salt spray (fog) test environment. Suitable apparatus which may be used is described in Appendix X1. 1.2 This practice does not prescribe the type of test specimen or exposure periods to be used for a specific product, nor the interpretation to be given to the results. 1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Standard Practice for Operating Salt Spray (Fog) Apparatus
- ICS
- 77.060
- CCS
- 发布
- 2019-11-01
- 实施
Corrosion of metals and alloys — Corrosion and fouling in industrial cooling water systems — Part 1: Guidelines for conducting pilot-scale evaluation of corrosion and fouling control additives for ope
- ICS
- 77.060
- CCS
- 发布
- 2019-10-31
- 实施
Corrosion of metals and alloys — Stress corrosion testing — Part 6: Preparation and use of pre-cracked specimens for tests under constant load or constant displacement
- ICS
- 77.060
- CCS
- 发布
- 2019-10-31
- 实施
Corrosion of metals and alloys — Corrosion and fouling in industrial cooling water systems — Part 1: Guidelines for conducting pilot-scale evaluation of corrosion and fouling control additives for ope
- ICS
- 77.060
- CCS
- 发布
- 2019-10-31
- 实施
Determination of resistance to intergranular corrosion of stainless steels — Part 2: Ferritic, austenitic and ferritic-austenitic(duplex) stainless steels — Corrosion test in media containing sulfuric
- ICS
- 77.060
- CCS
- 发布
- 2019-10-31
- 实施
Determination of resistance to intergranular corrosion of stainless steels — Part 1: Austenitic and ferritic-austenitic(duplex) stainless steels — Corrosion test in nitric acid medium by measurement o
- ICS
- 77.060
- CCS
- 发布
- 2019-10-31
- 实施
Corrosion of metals and alloys — Alternate immersion test in salt solution
- ICS
- 77.060
- CCS
- 发布
- 2019-10-31
- 实施
Corrosion tests in artificial atmosphere at very low concentrations of polluting gas(es)
- ICS
- 77.060
- CCS
- 发布
- 2019-10-31
- 实施
Corrosion of Metals and alloys — Removal of corrosion products from corrosion test specimens
- ICS
- 77.060
- CCS
- 发布
- 2019-10-31
- 实施
Corrosion of metals and alloys — Stress corrosion testing — Part 5: Preparation and use of C-ring specimens
- ICS
- 77.060
- CCS
- 发布
- 2019-10-31
- 实施
