77.120.60 铅、锌、锡及其合金 标准查询与下载

JIS H 1123:2021 铅金属光电发射光谱分析方法

Method for photoelectric emission spectrochemical analysis of lead metal

YS/T 1415-2021 湿法炼锌浸出液中酸度的测定 络合掩蔽—中和滴定法

Determination of acidity in hydrometallurgical zinc leaching solution complex masking-neutralization titration method

KS D 1682-2020 铅金属光电发射光谱分析方法

Method for photoelectric emission spectrochemical analysis of lead metal

KS D 5512-2020 铅片和板以及硬铅片和板

Lead sheets and plates and hard lead sheets and plates

ASTM B560-20 现代锡合金标准规范

1.1 This specification covers three Pewter alloy types as shown in Table 1, made from tin, antimony, and copper, used in the production and fabrication of finished or semi-finished pewter products by casting, spinning, drawing, or forming. The metal may be supplied in the form of bars, ingots, rolled sheet, and circles. 1.2 Pewter alloy shall be defined as having a composition within the range from 90 to 98 % tin, 1 to 8 % antimony, and 0.25 to 3 % copper. Compositions are given in Table 1. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Modern Pewter Alloys

ASTM B982-20 用于光发射光谱或ICP分析的铅和铅合金的取样和样品制备标准规范

1.1 This specification covers the sampling of lead and lead alloys to obtain a sample suitable for quantitative optical emission spectrochemical analysis. Included are procedures for sample preparation, obtaining representative samples from molten metal, from fabricated, or cast products that can be melted, and from other forms that cannot be melted. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Sampling and Sample Preparation of Lead and Lead Alloys for Optical Emission Spectrometric or ICP Analysis

ASTM B69-20 轧制锌标准规格

Standard Specification for Rolled Zinc

T/CNIA 0048-2020 绿色设计产品评价技术规范 铅锭

本标准规定了铅锭绿色设计产品评价的术语和定义、评价要求、产品生命周期评价报告编制方法，以及评价方法和流程。 本标准适用于以铅精矿、铅膏或其他含铅物料为原料，经过火法熔炼、电解精炼生产的铅锭的绿色设计产品评价。

Green design product evaluation technical specification lead ingot

YS/T 1345.6-2020 高铋铅化学分析方法 第6部分：锡含量的测定 碘酸钾滴定法

Methods for chemical analysis of high bismuth lead Part 6: Determination of tin content Potassium iodate titration method

YS/T 1345.4-2020 高铋铅化学分析方法 第4部分：锑含量的测定 火焰原子吸收光谱法和硫酸铈滴定法

Methods for chemical analysis of bismuth-rich lead Part 4: Determination of antimony content Flame atomic absorption spectrometry and cerium sulfate titration

YS/T 1345.2-2020 高铋铅化学分析方法 第2部分：铋含量的测定 Na2EDTA滴定法

Methods for chemical analysis of bismuth-rich lead Part 2: Determination of bismuth content Na2EDTA titration method

YS/T 1345.3-2020 高铋铅化学分析方法 第3部分：金和银含量的测定 火试金重量法

Methods for chemical analysis of bismuth-rich lead Part 3: Determination of gold and silver content Fire gold gravimetric method

YS/T 1345.5-2020 高铋铅化学分析方法 第5部分：铜含量的测定 火焰原子吸收光谱法

Methods for chemical analysis of bismuth-rich lead Part 5: Determination of copper content Flame atomic absorption spectrometry

YS/T 1345.1-2020 高铋铅化学分析方法 第1部分：铅含量的测定 Na2EDTA滴定法

Methods for chemical analysis of high bismuth lead - Part 1: Determination of lead content Na2EDTA titration method

KS D 2305-2019 锡金属

Tin metal

KS D 1757-2019 金属锌中镉的测定方法

Methods for determination of cadmium in zinc metal

KS D 1756-2019 锌金属中铅的测定方法

Methods for determination of lead in zinc metal

KS D 1929-2019 压铸锌合金光电发射光谱化学分析方法

Methods for photoelectric emission spectrochemical analysis of die casting zinc alloys

ASTM B339-19 猪锡标准规格

1.1 This specification covers refined tin in pig form recovered and cast from primary and secondary tin-bearing materials. One grade of tin metal is specified and is designated by the grade letter shown in Table 1. 1.2 The percent values of tin contained are to be regarded as the standard. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Pig Tin

YS/T 1341.5-2019 粗锌化学分析方法 第5部分：铜含量的测定 火焰原子吸收光谱法

Methods of chemical analysis of crude zinc Part 5: Determination of copper content Flame atomic absorption spectrometry