77.120.60 铅、锌、锡及其合金 标准查询与下载

ASTM B852-16(2022) 钢板热浸镀锌用连续镀锌级（CGG）锌合金标准规范

1.1 This specification covers grades of zinc alloys, commonly known as Continuous Galvanizing Grade (CGG) alloys that contain aluminum, or aluminum and lead, that are used in continuous hot-dip galvanizing of steel sheet. The compositions for CGG grades made from primary zinc are shown in Table 1. Exceptions for grades made from secondary zinc are found in footnote C. 1.2 CGG alloys specified in Specification B852 are used in continuous hot-dip galvanizing of steel sheet to produce product, as specified in Specification A653/A653M. 1.3 Other alloy compositions not included in Specification B852, and as may be agreed upon between the producer and the user, may be used for continuous galvanizing. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Continuous Galvanizing Grade (CGG) Zinc Alloys for Hot-Dip Galvanizing of Sheet Steel

ASTM B860-18(2022) 热浸镀锌用锌母合金标准规范

1.1 This specification covers zinc master alloys which are used in hot dip galvanizing for the purpose of adjusting the concentration of certain alloying elements in the molten zinc bath. Table 1 covers the chemical composition of these materials which include six master alloys of zinc-aluminum (brightener) and one master alloy of zinc-antimony. ASTM Common UNS Type A-1 90/10 Zn/Al High Purity Z30750 Type A-2 90/10 Zn/Al Low Purity Z31710 Type A-3 95/5 Zn/Al High Purity Z30503 Type A-4 95/5 Zn/Al Low Purity Z31510 Type A-5 96/4 Zn/Al High Purity Z31520 Type A-6 96/4 Zn/Al Low Purity Z30504 Type S-1 90/10 Zn/Sb Z55710 NOTE 1—The master alloys in Specification B860 are intended to be used primarily in hot-dip galvanizing to adjust the concentration of certain elements in a molten zinc bath, and differ from the zinc-aluminum alloys in Specification B997 which are intended to be used primarily in molten zinc-aluminum. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Zinc Master Alloys for Use in Hot Dip Galvanizing

YS/T 1530-2022 高纯锡化学分析方法 杂质元素含量的测定 辉光放电质谱法

本文件适用于高纯锡中杂质元素含量的测定。各元素测定范围：0.001 μg/g~5 μg/g。

High purity tin chemical analysis method Determination of impurity element content Glow discharge mass spectrometry

KS D 5589-2022 镀锡铜卷板

Tinned copper coiled sheets

KS D 6018-2022 硬铅铸件

Hard lead castings

T/CNIA 0145-2022 绿色设计产品评价技术规范 铸造用锌合金锭

本文件规定了铸造用锌合金锭绿色设计产品评价的评价要求、产品生命周期评价报告编制方法，以及评价方法和流程。

Green Design Product Evaluation Technical Specifications Zinc Alloy Ingots for Casting

KS D ISO 714-2022 锌 铁含量的测定 光度法

Zinc－Determination of iron content－Photometric method

KS D ISO 4192-2022 铝及铝合金 铅含量的测定 火焰原子吸收光谱法

Aluminium and aluminium alloys－Determination of lead content－Flame atomic absorption spectrometric method

KS D ISO 3750-2022 锌合金 镁含量的测定 火焰原子吸收光谱法

Zinc alloys－Determination of magnesium content－Flame atomic absorption spectrometric method

ASTM B750-22 热浸镀锌用铸锭形式的GALFAN（锌-5%铝-混合稀土）合金标准规范

1.1 This specification covers GALFAN, zinc-5 % aluminum-mischmetal (Zn-5Al-MM) alloy (UNS Z38510)3 in ingot form for remelting for use in the production of hot-dip coatings on steel. Alloy composition is specified in Table 1. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for GALFAN (Zinc-5 % Aluminum-Mischmetal) Alloy in Ingot Form for Hot-Dip Coatings

T/CFA 0102033-2022 压铸锌合金

本文件规定了压铸锌合金的牌号及代号，技术要求，试验方法，检验规则，包装、贮存、运输和质量证明书等要求。

Zinc alloys for die casting

SN/T 5412-2022 钴精矿中钴、铜和锰含量的测定 波长色散X射线荧光光谱法

Determination of cobalt, copper and manganese content in cobalt concentrates by wavelength dispersive X-ray fluorescence spectrometry

SN/T 5413-2022 镍矿、镍精矿及主要含镍物料鉴别方法

Identification method of nickel ore, nickel concentrate and main nickel-containing materials

SN/T 5409-2022 锌冶炼用氧化锌富集物鉴别方法

Identification method of zinc oxide enrichment for zinc smelting

SN/T 5410.1-2022 铅矿及主要含铅的矿渣鉴别方法 第1部分：通则

Methods for identification of lead ores and slags mainly containing lead Part 1: General principles

SN/T 5411-2022 钴精矿及主要含钴物料鉴别方法

Identification method of cobalt concentrate and main cobalt-containing materials

T/SHMHZQ 158-2021 拉链头生产技术规范

4 生产设施  4.1 厂房  4.2 设施  4.3 设备  5 原料要求  6 生产工艺  6.1 工艺流程  6.2 工序要点  7 生产管理  7.1 基本要求  7.2 安全生产  7.3 质量控制  7.4 人员  8 生产记录

Technical specification for production of zipper head

T/SHMHZQ 115-2021 压铸锌合金通用规范

4 生产工艺流程 5 要求 6 试验方法 7 检验规则 8 标志、包装、运输和贮存

General specification for die cast zinc alloys

T/SHMHZQ 116-2021 锌锭通用规范

3 术语和定义 4 要求 5 试验方法 6 检验规则 7 标志、包装、运输和贮存

General specification for zinc ingot

YS/T 1462.5-2021 粗锡化学分析方法 第5部分：锑含量的测定 火焰原子吸收光谱法和硫酸铈滴定法

Methods for chemical analysis of crude tin Part 5: Determination of antimony content Flame atomic absorption spectrometry and cerium sulfate titration