77.140.01 钢铁产品综合 标准查询与下载

DB13/T 2467-2017 石油套管用热轧钢带通用技术要求

General technical requirements for hot-rolled steel strip for oil casing

ASTM A1040-17 说明锻制碳素, 低合金和合金钢用协调标准等级组合的标准指南

4.1 It is anticipated that the ASTM Subcommittees A01.02, A01.03, A01.06, A01.09, A01.11, A01.15, A01.19, A01.22, and A01.28 will use the standard composition limits listed in this guide for the grades identified in their product specifications unless there is a specific technical justification for doing otherwise. 4.2 The composition limits given in this guide are to be used as guides in determining limits for each of the elements included in the total composition of each grade. The composition limits have been established with the intent that each ASTM subcommittee will find it necessary to require only a minimum number of changes to reflect specific technical effects. Section 5 lists the general guidelines followed for determining the limits for each element; the limits established in this guide are based upon these guidelines. 1.1 This guide covers ASTM Subcommittees A01.02, A01.03, A01.06, A01.09, A01.11, A01.15, A01.19, A01.22, and A01.28 for specifying chemical composition limits of wrought carbon, low-alloy, and alloy steels. It is intended that these recommended grade composition limits be suitable for adoption by other standardization bodies that prepare standards for carbon, low-alloy, and alloy steel products, including discontinued steels. 1.2 Included in this guide are the recommendations for determining the number of significant figures for specifying chemical composition. 1.3 The carbon and alloy steel grades in all standards overseen by the aforementioned ASTM subcommittees have been included, except those grades applicable to restricted special end uses. 1.4 Not addressed are minor composition modifications that a specific ASTM subcommittee may find necessary to accommodate effects of normal processing or to enhance fabricability by the producer or user, or both. 1.5 Also not generally addressed (except where established by ASTM subcommittees) is a complete rationalization of all limits, especially where such would conflict with long-standing practices and is not justified by special technical effect. 1.6 This guide does not address discontinued or formerly standard steel grades. A listing of such steel grades can be found in SAE J1249. Also excluded from this guide are cast materials and welding filler metals. 1.7 In 1995, the AISI made the decision to transfer the responsibility of maintaining its numbering system to the Society of Automotive Engineers (SAE) for carbon and alloy steels (SAE J403 and SAE J404) and to ASTM International for stainless steels (Guide A959 and others). To inform users of this important event, historical information is included in the appendix of this standard. 1.8 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered s......

Standard Guide for Specifying Harmonized Standard Grade Compositions for Wrought Carbon, Low-Alloy, and Alloy Steels

GSO ISO 630-3:2016 结构钢 第3部分：细晶粒结构钢的技术交货条件

This part of ISO 630 specifies requirements for flat and long products of hot-rolled weldable fine-grain structural steels in the as-rolled (for SG grades only), normalized/normalized-rolled and thermomechanical-rolled delivery conditions. It applies to steel plates rolled on a reversing mill, wide flats, hot-rolled sections and bars, which are intended for use in heavily loaded parts of welded or bolted structures. This part of ISO 630 covers 11 grades and four qualities. Grades S275, S355, S420 and S460 are covered in Annex A. Grades SG245, SG290, SG325, SG345, SG365, SG415 and SG460 are covered in Annex B. Not all grades are available in all qualities, and some qualities have Charpy V-notch requirements. This part of ISO 630 does not include the following structural steels, some of which are covered by other International Standards: — Sheet and strip — refer to ISO TC 17/SC 12, Continuous mill flat rolled products; — Tubular products — refer to ISO TC 5/SC 1, Steel tubes. NOTE Lists of standards covered by ISO/TC 17/SC 12 and ISO/TC 5/SC 1 are available on the ISO Web site.

Structural steels -- Part 3: Technical delivery conditions for fine-grain structural steels

GSO ISO 630-4:2016 结构钢 第4部分：高屈服强度调质结构钢板交货技术条件

This part of ISO 630 specifies qualities for high-yield-strength quenched and tempered structural steels. This part of ISO 630 applies to steel plates rolled on a reversing mill which are used in the quenched and tempered condition and normally intended for welded or bolted structures. This part of ISO 630 does not include the following structural steels, some of which are covered by other International Standards: — Sheet and strip — refer to ISO TC 17/SC 12, Continuous mill flat rolled products; — Tubular products — refer to ISO TC 5/SC 1, Steel tubes. NOTE Lists of standards covered by ISO/TC 17/SC 12 and ISO/TC 5/SC 1 are available on the ISO Web site. This part of ISO 630 covers 10 grades. Grades S460Q, S500Q, S550Q, S620Q, S690Q, S890Q and S960Q are covered in Annex A. Grades SG460Q, SG500Q, and SG700Q are covered in Annex B.

Structural steels -- Part 4: Technical delivery conditions for high-yield-strength quenched and tempered structural steel plates

KS D 3865-2016 建筑结构用耐火钢

Fire resistance steels for building structure

SN/T 4564-2016 电工钢片（带）晶粒取向性鉴定用金相试样制备方法

Preparation method of metallographic specimens for identification of grain orientation of electrical steel sheets (strips)

SN/T 4563-2016 电工钢片（带）晶粒取向性鉴定方法 金相法

Method for identification of grain orientation of electrical steel sheets (strips) Metallographic method

DB13/T 2328-2016 钢铁企业通用质量要求

General quality requirements for iron and steel enterprises

DB13/T 2329-2016 钢铁企业通用技术要求

General Technical Requirements for Iron and Steel Enterprises

GSO ISO 1052:2015 一般工程用钢

1.1 This International Standard specifies the qualities of general purpose steel set out in table 1 intended for engineering purposes. 1.2 This International Standard applies to hot-rolled steel sheet 3 mm or more thick, flats and bars generally used in the delivered state and as a rule in engineering structures. It does not deal with the following steels, which are dealt with in other International Standards : — steels for boilers and pressure vessels (ISO 2604/4); — sheet for forming and stamping (ISO 3573 and ISO 3574); — structural steels for heat treatment; — bars for concrete; — general-purpose steels intended for metal construc-tions (ISO 630).

Steels for general engineering purposes

SAE AMS2489A-2015 钢材发黑补漆法

This specification covers the requirements for an inorganic black coating applied at ambient temperature to steel to touch up black oxide coating in areas where the black oxide has been removed. This coating is intended only to visually change the surface to a black color, not to meet the requirements of any black oxide specification.

Blackening of Steel Touch Up Method

GOST 31458-2015 钢和铸铁管及配件. 检验文件

Steel and cast iron pipes and fittings. Inspection documents

GOST R 56731-2015 混凝土用锚固. 试验方法

Anchors for use in concrete. Test methods

ASTM A1080-15 高温等静力压制钢, 不锈钢和相关合金铸件的标准实践规程

1.1 This practice covers general requirements for Hot Isostatic Pressing (HIP) of steel, stainless steel, and related alloy castings. 1.2 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Hot Isostatic Pressing of Steel, Stainless Steel, and Related Alloy Castings

JIS G 0415:2014 钢和钢制品.检验文件

This Standard defines the different types of inspection documents supplied to the purchaser,in accordance with the requirements of the order,for the delivery of steel and steel products specifiesd in Japanese industrial Standards.This Standard is also applicable to other products upon agreement between the purchaser and the manufacturer.

Steel and steel products -- Inspection documents

GSO ISO 10474:2013 钢材及钢材产品检验文件

This International Standard defines the different types of inspection documents supplied to the purchaser, in accordance with the requirements of the order, for the delivery of steel products. This International Standard is to be used in conjunction with other International Standards which specify the general technical delivery conditions: — for steel and steel products, see ISO 404; — for steel castings, see ISO 4990. NOTE This International Standard can also apply to other products

Steel and steel products -- Inspection documents

KS D ISO 1052:2013 一般工程用钢

Steels for engineering purposes

BS ISO 10474:2013 钢和钢制品.检验文件

Steel and steel products. Inspection documents

ISO 10474:2013 钢和钢制品.检验文件

This International Standard defines the different types of inspection documents supplied to the purchaser, in accordance with the requirements of the order, for the delivery of steel products. This International Standard is to be used in conjunction with other International Standards which specify the general technical delivery conditions: — for steel and steel products, see ISO 404; — for steel castings, see ISO 4990. NOTE This International Standard can also apply to other products.

Steel and steel products - Inspection documents

UL 2840-2013 建筑产品中用钢制品的可持续性

Sustainability for Steel for Use in Construction Products