77.140.65 钢丝、钢丝绳和环节链 标准查询与下载

T/CISA 352-2024 电梯提升带用钢丝绳

本文件规定了电梯提升带用钢丝绳的术语和定义、分类与标记、技术要求、试验方法、检验规则、验收、包装、贮存和运输、标志和质量证明书。                                                                                                                                                                                                                                                               本文件适用于公称直径为1.2 mm～3.0 mm的电梯提升带用包覆钢丝绳。

Steel wire ropes for elevator lifting belt

T/CISA 353-2024 工程机编钢丝网用钢丝 涂塑层 厚度均匀性试验方法

本文件描述了工程机编钢丝网用钢丝涂塑层厚度均匀性的术语和定义、试验设备及工具、试验原理、取样、试验方法与步骤、仲裁检验和数字修约。 本文件适用于工程机编钢丝网用钢丝涂塑层厚度均匀性检测。其他涂塑钢丝涂塑层厚度均匀性检测也可以参照执行。

Steel wire for engineering woven wire mesh — Plastic coating — Thickness uniformity test

YB/T 6091-2023 桥梁缆索企业绿色工厂评价要求

本文件规定了桥梁缆索企业绿色工厂评价的基本原则、评价指标体系及要求、评价程序。本文件适用于桥梁缆索企业绿色工厂的评价。

Green factory evaluation requirements for bridge and cable companies

YB/T 6090-2023 钢帘线企业绿色工厂评价要求

本文件规定了钢帘线企业绿色工厂评价的术语和定义、总则、评价要求、评价程序和评价报告。本文件适用于钢帘线企业绿色工厂的评价。

Green factory evaluation requirements for steel cord enterprises

DB32/T 4601-2023 桥梁缆索用锌-10%铝-稀土多元合金镀层钢丝通用技术条件

General technical conditions for zinc-10% aluminum-rare earth multicomponent alloy coated steel wire for bridge cables

T/QGCML 2054-2023 柔性超耐磨抗拉钢丝绳

本文件规定了柔性超耐磨抗拉钢丝绳的分类和标记、订货内容、材料、技术要求、试验方法、检验规则、标志、包装、运输和贮存、安全使用和维护。 本文件适用于柔性超耐磨抗拉钢丝绳的生产和检验。

Flexible super wear-resistant tensile steel wire rope

ASTM C933-23 焊接钢丝车床标准规范

1.1 This specification covers welded wire lath, flat or self-furring, with or without backing, designed for use as a base to receive portland cement-based interior plaster and exterior stucco. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Welded Wire Lath

ASTM B958/B958M-23 架空导线用超高强度和超高强度A级锌-5%铝混合稀土合金涂层钢芯线的标准规范

1.1 This specification covers round, extra-high-strength, and ultra-high-strength, Class A coated zinc–5 % aluminummischmetal (Zn–5Al–MM) alloy-coated, steel core wire for use in Overhead Electrical Conductors. 1.2 This specification covers wire of diameter from 0.0500 in. to 0.1900 in. inclusive or 1.27 mm to 4.82 mm inclusive. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Extra-High-Strength and Ultra-High-Strength Class A Zinc–5% Aluminum-Mischmetal Alloy-Coated Steel Core Wire for Use in Overhead Electrical Conductors

ASTM B957/B957M-23 架空导线用超高强度和超高强度镀锌（镀锌）钢芯线的标准规范

1.1 This specification covers round, extra-high-strength and ultra-high-strength, Class A zinc-coated (galvanized), steel core wire used for use in Overhead Electrical Conductors. 1.2 This specification covers wire of diameter from 0.0500 in. to 0.1900 in. inclusive or 1.27 mm to 4.82 mm inclusive. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Extra-High-Strength and Ultra-High-Strength Zinc-Coated (Galvanized) Steel Core Wire for Use in Overhead Electrical Conductors

ASTM B910/B910M-07(2023) 退火铜包钢丝的标准规范

Standard Specification for Annealed Copper-Clad Steel Wire

ASTM A741-23 公路护栏用金属涂层钢丝绳和配件标准规范

Standard Specification for Metallic-Coated Steel Wire Rope and Fittings for Highway Guardrail

ASTM A809-23 镀铝（渗铝）碳素钢丝的标准规范

1.1 This specification covers soft, medium, and hard temper carbon steel wire coated with aluminum by a hot-dip process, supplied in coils for general use. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Aluminum-Coated (Aluminized) Carbon Steel Wire

T/QGCML 1584-2023 PC钢棒

本文件规定了 PC 钢棒的分类、代号及标记、订货内容、尺寸、重量及允许偏差、技术要求、试验方法、检验规则、包装、标志及质量证明书。 本文件适用于 PC 钢棒的生产、检验、采购活动。

PC Gangbang

T/QGCML 1491-2023 汽车用冷拔低碳钢丝

本文件规定了汽车用冷拔低碳钢丝的术语和定义、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本文件适用于汽车用冷拔低碳钢丝，以下简称“钢丝”。

Cold drawn low carbon steel wire for automobiles

ASTM A555/A555M-23 不锈钢线材和盘条一般要求标准规范

1.1  This specification covers general requirements that shall apply to stainless wire and wire rods. Wire rods are a semifinished product intended primarily for the manufacture of wire. Wire is intended primarily for cold forming, including coiling, stranding, weaving, heading and machining as covered under the latest revision of each of the following ASTM specifications: A313/A313M , A368 , A478 , A492 , A493 , A580/A580M , and A581/A581M . 1.2  In case of conflicting requirements, the individual material specification and this general requirement specification shall prevail in the order named. 1.3  General requirements for flat products other than wire are covered in Specification A480/A480M . 1.4  General requirements for bar and billet products are covered in Specification A484/A484M . 1.5  The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.6  Unless the order specifies the applicable metric specification designation, the material shall be furnished in the inch-pound units. 1.7  This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for General Requirements for Stainless Steel Wire and Wire Rods

ASTM F552-14(2023) 与勾花栅栏相关的标准术语

Standard Terminology Relating to Chain Link Fencing

T/CRIA 29004-2023 胎圈钢丝涂层中古马隆树脂含量的测定

本文件规定了分光光度法测定胎圈钢丝涂层古马隆树脂含量，原理，测试的试剂和材料，仪器和设备，试验步骤，结果计算，结果表达和试验报告。 本文件仅适用于橡胶轮胎用胎圈钢丝涂层古马隆树脂含量的测定。

Determination of coumaron resin content in bead wire coating

ASTM A981/A981M-23 用于预应力地锚的直径0.600-in.[15.24-mm]的270级[1860]七线钢绞线粘结强度评定的标准试验方法

1.1 This test method describes procedures to establish the relative bond strength of 0.600 in. [15.24 mm] diameter, Grade 270 [1860] seven-wire steel strand in cement grout as used in prestressed ground anchors for the purpose of evaluating the effects of manufacturing practices on bond strength. 1.2 The bond strength values obtained are not intended to be used to design the bond length of ground anchors that depend on field conditions. 1.3 This test method is not intended to be used as a bond test for prestressed concrete applications. 1.4 The values stated in either inch-pound or SI units are to be regarded as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Evaluating Bond Strength for 0.600-in. [15.24-mm] Diameter Seven-Wire Steel Strand, Grade 270 [1860], Used in Prestressed Ground Anchors

ASTM F2611-23 链式安全围栏的设计和施工标准指南

1.1 This guide covers the material and installation for selection in the design of a security chain link fence system. The proper material selection, system installation and layout can substantially increase the difficulty to penetrate; thereby, increasing the intrusion delay time. 1.2 This guide does not purport to address all of the physical protection security concerns. It is the responsibility of the user of this standard to establish the appropriate design for the level of physical protection required and determine the applicability of regulatory requirements or limitations prior to use. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 It is recommended that Guide F1553 be followed for the format of this guide. 1.5 This guide is not intended to set specific requirements for chain link security fencing. It intends to cover the considerations or options pertinent to the design and construction of chain link security fencing. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Design and Construction of Chain Link Security Fencing

YB/T 6104-2023 线材用砂带除锈机技术规范

本文件规定了线材用砂带除锈机的术语和定义、型式及基本参数、订货内容、技术要求、试验方法与验收规则、标志、包装、运输与贮存和制造保证。本文件适用于采取砂带磨削形式对制丝用线材、热处理半成品钢丝表面氧化铁皮及锈迹的清除。

Technical Specifications for Abrasive Belt Rust Remover for Wire Rods