77.140.65 钢丝、钢丝绳和环节链 标准查询与下载

ASTM B957/B957M-22 用于架空电导体的超高强度和超高强度镀锌（镀锌）钢芯线的标准规范

1.1 This specification covers round, extra-high-strength and ultra-high-strength, Class A zinc-coated (galvanized), steel core wire used for use in Overhead Electrical Conductors. 1.2 This specification covers wire of diameter from 0.0500 in. to 0.1900 in. inclusive or 1.27 mm to 4.82 mm inclusive. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Extra-High-Strength and Ultra-High-Strength Zinc-Coated (Galvanized) Steel Core Wire for Overhead Electrical Conductors

YB/T 4996-2022 索氏体化热处理碳素钢丝

本文件规定了索氏体化热处理碳素钢丝的术语和定义、分类及标记、订货内容、技术要求、检验和试验、验收方法、包装、标志、运输、贮存和质量证明书等。 本文件适用于碳含量0.32%~0.90%、直径0.80mm~16.00mm，经过铅液、盐液、水溶性有机物等淬火介质进行索氏体化热处理的碳素钢丝。 索氏体化热处理盘条可参照本文件执行。

Sorting heat treated carbon steel wire

YB/T 6032-2022 制簧用钢丝绳

本文件规定了制簧用钢丝绳的术语和定义、分类和标记、订货内容、材料、技术要求、检查与试验、检验规则、包装、标志及质量证明书。 本文件适用于汽车座靠垫、床垫、以及其他家具、室内装饰等弹簧用钢丝绳。

Wire rope for spring making

YB/T 6079-2022 胎圈钢丝试验方法

本文件规定了胎圈用钢丝的试样一般规定、外观质量、尺寸、工艺性能、力学性能、镀层分析试验方法、粘合性能试验方法。 本文件适用于各类轮胎胎圈用回火圆形钢丝的试验方法。

Bead wire test method

YB/T 6030-2022 汽车掣动推拉索芯

本文件规定了汽车掣动推拉索芯的定义、分类和标记、订货内容、材料、技术要求、试验方法、检验规则、质量保证期、包装、贮存、运输及质量证明书。 本文件适用于汽车选换档掣动总成、刹车掣动总成用推拉索芯。工程机械、轨道交通、游艇、船舶、航空飞行器等其他控制总成用推拉索芯也可参照本文件执行。

Car brake push-pull cable core

YB/T 6031-2022 汽车发动机燃油导轨用不锈钢丝及棒

本文件规定了汽车发动机燃油导轨用不锈钢丝及棒的订货内容、尺寸、外形及允许偏差、技术要求、试验方法、检验规则、包装、标志和质量证明书。 本文件适用于直径10.00 mm ～50.00 mm的汽车发动机燃油导轨用不锈钢丝及棒。

Stainless steel wire and rod for automobile engine fuel rail

ASTM A581/A581M-22 高速切削用耐热不锈钢丝和盘条的标准规格

Standard Specification for Free-Machining Stainless Steel Wire and Wire Rods

ASTM A555/A555M-22 不锈钢丝和盘条一般要求的标准规范

1.1 This specification covers general requirements that shall apply to stainless wire and wire rods. Wire rods are a semifinished product intended primarily for the manufacture of wire. Wire is intended primarily for cold forming, including coiling, stranding, weaving, heading and machining as covered under the latest revision of each of the following ASTM specifications: A313/A313M, A368, A478, A492, A493, A580/A580M, and A581/A581M. 1.2 In case of conflicting requirements, the individual material specification and this general requirement specification shall prevail in the order named. 1.3 General requirements for flat products other than wire are covered in Specification A480/A480M. 1.4 General requirements for bar and billet products are covered in Specification A484/A484M. 1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.6 Unless the order specifies the applicable metric specification designation, the material shall be furnished in the inch-pound units. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for General Requirements for Stainless Steel Wire and Wire Rods

KS D 7063-2022 镀锌钢丝

Zinc-coated steel wires

22/30455581 DC BS EN 10264-3 钢丝及线材制品 绳索用钢丝 第 3 部分：用于高负荷应用的圆形和异形非合金钢丝

BS EN 10264-3. Steel wire and wire products. Steel wire for ropes. - Part 3. Round and shaped non alloyed steel wire for high duty applications

ASTM A1007-22 钢丝绳用碳钢钢丝的标准规范

1.1 This specification covers uncoated and metallic coated classes of round, cold-drawn, carbon steel wire for wire rope in five strength levels. This specification specifies: 1.1.1 Dimensional tolerances, 1.1.2 Mechanical characteristics, 1.1.3 Chemical composition requirements, 1.1.4 Coating requirements (if applicable), and 1.1.5 Packaging requirements. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Carbon Steel Wire for Wire Rope

ASTM A1096/A1096M-22 评定混凝土钢筋用凹痕或普通钢丝粘结性的标准试验方法

1.1 This test method describes procedures for evaluating bond of individual steel wire, indented or plain, for concrete reinforcement. The bond determined by this test method is stated as the tensile force needed to pull the wire through the cured mortar in a cylindrical steel casing. 1.2 The result of the test is the maximum tensile force measured on the loaded end of the wire recorded at a free-end slip less than or equal to 0.10 in. [2.5 mm]. 1.3 Units—The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Evaluating Bond of Individual Steel Wire, Indented or Plain, for Concrete Reinforcement

GSO ISO 3108:2022 钢丝绳 试验方法 测量破断拉力的测定

ISO 3108:2017 specifies a method of tensile test to destruction for determining the actual breaking force of steel wire ropes as given in ISO 2408. It is also applicable for other ropes, unless the International Standard concerned specifically excludes its use, or gives another method.

Steel wire ropes — Test method — Determination of measured breaking force

GSO ISO 2408:2022 钢丝绳 要求

ISO 2408:2017 specifies requirements for the manufacture, testing, acceptance, packing, marking and issuing of a certificate of quality of wire ropes. It is applicable to round strand ropes and compacted strand ropes made from wires ropes that are uncoated (bright), zinc-coated or Zn-Al coated. It is not applicable to ropes for - mining purposes, - aircraft control, - aerial ropeways and funiculars, and - lifts.

Steel wire ropes — Requirements

T/SSEA 0183-2022 金属饰品用镀锌钢丝

本文件规定了金属饰品用镀锌钢丝的订货内容、尺寸、外形、重量、技术要求、试验方法、检验规则、包装、运输、贮存、标志及质量证明书。 本文件适用于制造手镯、手链、项链、眼镜架、宠物链等金属饰品用公称直径0.40mm~5.50mm的镀锌钢丝。

Galvanized steel wire for metal ornaments

T/SSEA 0182-2022 清洁球用镀锌钢丝

本文件规定了清洁球用镀锌钢丝的订货内容、尺寸、外形、重量、技术要求、试验方法、检验规则、包装、运输、贮存、标志及质量证明书。 本文件适用于制造清洁球用公称直径0.7mm~1.2mm的镀锌圆钢丝。

Galvanized steel wire for cleaning ball

T/SSEA 0184-2022 文教类包胶用镀锌钢丝

本文件规定了文教类包胶用镀锌钢丝的订货内容、尺寸、外形、重量、技术要求、试验方法、检验规则、包装、标志及质量证明书。 本文件适用于制造挂历圈、回形针等文教类PVC、PE包胶用公称直径1.20mm~2.50mm的镀锌圆钢丝。

Galvanized steel wire for culture and education

BS ISO 23717:2022 钢丝及线材制品 软管加固钢丝

1   Scope This document specifies the composition, dimensions and mechanical properties of steel wire with a high mass fraction of carbon, generally brass coated, for reinforcing high-pressure hoses. It is applicable to multiple parallel wires, braided or spirally wrapped for reinforcement in a rubber or synthetic hose that is made to withstand a relatively high bursting pressure.

Steel wire and wire products. Hose reinforcement wire

ASTM A411-08(2022) 镀锌（镀锌）低碳钢铠装线标准规范

1.1 This specification covers zinc-coated low-carbon steel wire for use in armoring for protection against damage of submarine and underground cables used for communication, control, or power purposes. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Zinc-Coated (Galvanized) Low-Carbon Steel Armor Wire

ASTM A121-22 金属涂层碳钢带刺铁丝的标准规范

1.1 This specification covers metallic-coated steel barbed wire, consisting of a strand of two wires. 1.2 The barbed wire is available with aluminum, zinc, and zinc-5 % aluminum-mischmetal alloy coatings, with a number of coating weights, in a number of different constructions (designs), and in two grades. Not all designs are available in all coating types. 1.3 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 The text of this specification references notes and footnotes that provide explanatory information. These notes and footnotes (excluding those in tables) shall not be considered as requirements of the specification. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Metallic-Coated Carbon Steel Barbed Wire