77.140.80 钢铁铸件 标准查询与下载

SAE J1993-2013 高碳铸钢粗砂

This SAE Recommended Practice describes the chemical composition, and physical characteristic requirements for high-carbon cast-steel grit, to be used for blast cleaning and etching operations.

High-Carbon Cast-Steel Grit

GSO ISO 3755:2013 一般工程用铸钢

1.1 This International Standard specifies requirements for eight grades of heat-treated cast carbon steels for general engineering purposes. Four of the grades have a restricted chemical composition to ensure uniform weldability. 1.2 In cases where castings are produced by welding together component parts, this International Standard does not cover the welding process or the properties of the weldment. 1.3 These grades are intended to be used at ambient temperature. However, properties at other temperatures may be agreed upon by using the supplementary requirements in 9.4.1 or 9.4.4 of ISO 4990:1986.

Cast carbon steels for general engineering purposes

DS/EN 13835:2013 创始 奥氏体铸铁

This European Standard specifies the grades and corresponding requirements for austenitic cast irons. These requirements are specified in terms of: graphite form and metal structure: either flake or spheroidal graphite in an austenitic matrix; chemical co

Founding - Austenitic cast irons

DS/EN 1563:2013 创立 球墨铸铁

This European Standard defines the grades and the corresponding requirements for spheroidal graphite cast irons. This European Standard specifies 2 groups of spheroidal graphite cast iron grades by a classification based on mechanical properties measured

Founding - Spheroidal graphite cast irons

DS/EN 1561:2013 创立 灰口铸铁

This European Standard specifies the properties of unalloyed and low-alloyed grey cast irons used for castings, which have been manufactured in sand moulds or in moulds with comparable thermal behaviour. This European Standard specifies the characterizing

Founding - Grey cast irons

DS/EN 1562:2013 创始 可锻铸铁

This European Standard defines grades and the corresponding requirements for malleable cast irons. This European standard specifies five grades of whiteheart malleable cast iron and nine grades of blackheart malleable cast iron, based on mechanical proper

Founding - Malleable cast irons

DS/EN 1564:2013 创立 奥氏体球墨铸铁

This European Standard defines the grades and the corresponding requirements for ausferritic spheroidal graphite cast irons. This European Standard specifies five grades of ausferritic spheroidal graphite cast iron by a classification based on mechanical

Founding - Ausferritic spheroidal graphite cast irons

NB/T 20007.20-2013 压水堆核电厂用不锈钢.第20部分:泵用马氏体不锈钢 A、B、C 类非承压铸造 内件

本部分规定了压水堆核电厂2、3级泵A、B、C类非承压可焊马氏体不锈钢铸造内件的制造、化学成分、力学性能、试验方法、无损检测等技术要求。本部分适用于压水堆核电厂2、3级泵A (包括A1和A2)、B (包括B1和B2)、C类非承压马氏体不锈钢铸件。

Stainless steel for pressurized water reactor power plant.Part 20: Martensitic stainless steel for non-pressure-retaining internal category A,B and C parts of pumps

NB/T 20007.23-2013 压水堆核电厂用不锈钢.第23部分:1、2、 3级奥氏体-铁素体不锈钢承压铸件

本部分规定了压水堆核电厂1、2、3级可焊奥氏体-铁素体不锈钢承压铸件的制造、试验、检验和验收等技术要求。本部分适用于压水堆核电厂1、2、3级可焊奥氏体-铁素体不锈钢承压铸件,其中含钼钢只允许用于工作温度低于250 ℃的铸件。本部分不适用于反应堆冷却剂泵蜗壳用奥氏体-铁素体不锈钢承压铸件及反应堆冷却剂系统管道用奥氏体-铁素体不锈钢离心浇铸管、铸造弯管和斜接管嘴。

Stainless steel for pressurized water reactor nuclear power plants.Part 23: Class 1、2 and 3 pressure-retaining austenitic-ferritic stainless steel castings

NB/T 20007.27-2013 压水堆核电厂用不锈钢.第27部分:反应堆冷却剂管道用奥氏体-铁素体不锈钢铸造弯头和斜接管嘴

本部分规定了压水堆核电厂反应堆冷却剂管道用奥氏体-铁素体不锈钢铸造弯头和斜接管嘴(以下简称“铸件”)的制造、化学成分、力学性能、组织检验、无损检测、缺陷部位的清除和焊补等技术要求。本部分适用于压水堆核电厂反应堆冷却剂管道用ZG04Cr20Ni9奥氏体-铁素体不锈钢铸造弯头和斜接管嘴。

Stainless steel for pressurized water reactor nuclear power plants.Part 27: Cast Elbows and inclined nozzles made from Austenitic-ferritic stainless steel for reactor coolant piping

NB/T 20007.24-2013 压水堆核电厂用不锈钢.第24部分:反应堆冷却剂泵蜗壳用奥氏体-铁素体不锈钢承压铸件

本部分规定了压水堆核电厂反应堆冷却剂泵蜗壳用奥氏体-铁素体不锈钢铸件的制造、化学成分、力学性能、无损检测等技术要求。本部分适用于压水堆核电厂反应堆冷却剂泵蜗壳用ZG04Cr20Ni9奥氏体-铁素体不锈钢铸件。

Stainless steel for pressurized water reactor nuclear power plants.Part 24: austenitic-ferritic stainless steel castings pressured for reactor coolant pump casing

NB/T 20005.6-2013 压水堆核电厂用碳钢和低合金钢.第6部分:反应堆冷却剂泵电动机机座铸件

本部分规定了压水堆核电厂冷却剂泵电动机机座用碳钢或低合金钢铸件的制造、化学成分、力学性能、无损检测、缺陷部位的清除和修补、尺寸检查等技术要求。本部分适用于压水堆核电厂冷却剂泵电动机机座用碳钢或低合金钢铸件。

Carbon steel and alloy steel for pressurized water reactor nuclear power plants.Part 6: Motor support stand castings for reactor coolant pumps

NB/T 20005.5-2013 压水堆核电厂用碳钢和低合金钢.第5部分:1、2、3 级承压铸件

本部分规定了压水堆核电厂用1、2、3级碳钢和低合金钢承压铸件的化学成分、力学性能、试验方法、检验规则及外形尺寸等技术要求。本部分适用于压水堆核电厂用1、2、3级碳钢和低合金钢承压铸件的制造和验收。本部分不适用于主蒸汽隔离阀阀体、主给水止回阀体及其他有特殊要求的碳钢和低合金钢铸件。

Carbon steel and low alloy steel for pressurized water reactor nuclear power plants.Part 5: Class 1, 2 and 3 pressure retaining castings

NB/T 20007.19-2013 压水堆核电厂用不锈钢.第19部分:1、2、 3 级马氏体不锈钢承压铸件

本部分规定了压水堆核电厂用1、2、3级可焊马氏体不锈钢承压铸件的制造、试验、检验和验收等技术要求。本部分适用于压水堆核电厂1、2、3级部件用ZG06Cr13Ni4Mo、ZG08Cr12Ni1、ZG07Cr16Ni4Cu3Nb可焊马氏体不锈钢承压铸件。

Stainless steel for pressurized water reactor nuclear power plants.Part 19: Class 1、2 and 3 pressure-retaining martensitic stainless steel castings

NB/T 20007.25-2013 压水堆核电厂用不锈钢.第25部分:泵用不含钼的铬镍奥氏体-铁素体不锈钢 A、B、 C类非承压铸造内件

本部分规定了压水堆核电厂泵用不含钼的铬镍奥氏体-铁素体不锈钢A、B、C类非承压铸造内件的制造、力学性能、无损检测、缺陷部位的清除和修补、尺寸检查等要求。本部分适用于压水堆核电厂泵用ZG04Cr20Ni9奥氏体-铁素体不锈钢A(包括A1、A2)、B (包括B1、B2)、C类非承压铸造内件。

Stainless steel for pressurized water reactor nuclear power plant.Part25: Chromium nickel austenitic-ferritic stainless steel containing no molybdenum for no-pressure-retaining cast internal pump parts of category A, B and C

JIS G 5505:2013 紧密石墨铸铁(蠕墨铸铁)

This Standard specifies CV graphite cast irons.

Compacted (vermicular) graphite cast irons

GSO ISO 10679:2013 钢 工具钢铸件

This International Standard covers tool-steel compositions for usable cast shapes in the annealed condition

Steel -- Cast tool steel

DS/EN 1559-3:2013 铸造 交货技术条件 第3部分：铸铁件的附加要求

This European Standard specifies the additional technical delivery conditions for castings made from all cast iron materials.This European Standard applies to iron castings produced in sand or permanent moulds or by centrifugal casting, continuous casting

Founding - Technical conditions of delivery - Part 3: Additional requirements for iron castings

DB13/T 1650-2012 双面埋弧螺旋焊管机组技术要求

本标准规定了双面埋弧螺旋焊管机组（以下简称机组）的术语和定义、结构、参数、技术要求、试验方法、检验规则、标志、包装、运输、贮存和安全使用说明书等。本标准适用于将低碳碳素结构钢或低合金结构钢钢带按一定的螺旋线的角度（叫成型角）卷成管坯，然后将管缝焊接起来相同工艺的设备机组的设计生产。

Technical requirements for double-sided submerged arc spiral welded pipe unit

ASTM A781/A781M-12b 标准规范铸件 钢和合金 通用要求 一般工业用

Standard Specification for Castings, Steel and Alloy, Common Requirements, for General Industrial Use