77.150.10 铝产品 标准查询与下载

YS/T 1455-2021 汽车天窗导轨用铝合金型材

Aluminum alloy profiles for automobile sunroof guide rails

YS/T 1515-2021 铝-空燃料电池用铝合金电极材料

Aluminum alloy electrode materials for aluminum-air fuel cells

ASTM B209/B209M-21a 铝及铝合金薄板和板材的标准规范

1.1 This specification2 covers aluminum and aluminumalloy flat sheet, coiled sheet, and plate in the alloys (Note 1) and tempers shown in Tables 2, 3, 4, and 5, and in the following finishes: 1.1.1 Plate in all alloys and sheet in heat-treatable alloys: mill finish. 1.1.2 Sheet in nonheat-treatable alloys: mill finish, one-side bright mill finish, standard one-side bright finish, and standard two-sides bright finish. 1.2 Alloy and temper designations are in accordance with ANSI H35.1/H35.1M. The equivalent Unified Numbering System alloy designations are those of Table 1 preceded by A9, for example, A91100 for aluminum 1100 in accordance with Practice E527. NOTE 1—Throughout this specification, use of the term alloy in the general sense includes aluminum as well as aluminum alloy. NOTE 2—See Specification B632/B632M for tread plate. NOTE 3—See Specification B928/B928M for 5xxx-H116 and 5xxxH321 aluminum alloys containing 3 % or more nominal magnesium and intended for marine service and similar environments. Other alloy-temper products listed in this specification, which do not require the additional corrosion testing/capability called out in Specification B928/B928M, may be suitable for marine and similar environment applications. 1.3 For acceptance criteria for inclusion of new aluminum and aluminum alloys in this specification, see Annex A2. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate

ASTM B769-11(2021) 铝合金剪切试验的标准试验方法

1.1 This test method covers double-shear testing of wrought and cast aluminum products to determine shear ultimate strengths. NOTE 1—The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are provided for information only. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Shear Testing of Aluminum Alloys

FprEN 12020-1-2021 铝和铝合金 合金挤压精密型材 EN AW-6060 和 EN AW-6063 第1部分：检验和交货的技术条件

Aluminium and aluminium alloys - Extruded precision profiles in alloys EN AW-6060 and EN AW-6063 - Part 1: Technical conditions for inspection and delivery

DIN EN 603-3:2021 铝和铝合金. 锻造坯料. 第3部分: 尺寸和形状公差; 德文版本EN 603-3-2021

This document specifies the tolerances on dimensions and form of wrought aluminium and aluminium alloy forging stock. It applies to extruded and rolled products.

Aluminium and aluminium alloys - Wrought forging stock - Part 3: Tolerances on dimensions and form; German version EN 603-3:2021

LST EN 1706+A1-2021 铝和铝合金 铸件 化学成分和机械性能

Aluminium and aluminium alloys - Castings - Chemical composition and mechanical properties

UNI EN 603-3-2021 铝和铝合金 锻造坯料 第3部分：尺寸和形状的公差

Aluminium and aluminium alloys - Wrought forging stock - Part 3: Tolerances on dimensions and form

ASTM B609/B609M-12(2021) 电气用退火和中间回火铝1350圆线的标准规范

1.1 This specification covers aluminum 1350-O (annealed), 1350-H12 or -H22 (1⁄4 hard), 1350-H14 or -H24 (1⁄2 hard), 1350-H16 or -H26 (3⁄4 hard) and 1350-H142 or -H242 (1⁄2 hard), suitable for stranding into conductors or for solid single conductors, either bare or insulated (see Table 1 or Table 2). 1.2 The values stated in inch-pound units or SI units are to be regarded separately as standard. The values in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. 1.2.1 For density, resistivity, and temperature, the values stated in SI units are to be regarded as standard. NOTE 1—Prior to 1975, aluminum 1350 was designated as ECaluminum. NOTE 2—The aluminum and temper designations conform to ANSI H35.1. Aluminum 1350 corresponds to Unified Numbering System A91350 in accordance with Practice E527. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Aluminum 1350 Round Wire, Annealed and Intermediate Tempers, for Electrical Purposes

ASTM B233-97(2021) 电气用铝1350拉伸坯料的标准规范

1.1 This specification covers aluminum 1350 drawing stock 0.375 in. (9.52 mm) to 1.000 in. (25.40 mm) in diameter, in the tempers shown in Table 1, for drawing into wire for electrical conductors (Explanatory Note 1 and Note 2). 1.2 The SI values of density and resistivity are to be regarded as the standard. For all other properties the inchpound values are to be regarded as standard and the SI units may be approximate. NOTE 1—Prior to 1975, aluminum 1350 was designated as EC aluminum. NOTE 2—The aluminum and temper designations conform to ANSI H35.1. Aluminum 1350 corresponds to unified numbering system A91350 in accordance with Practice E527. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Aluminum 1350 Drawing Stock for Electrical Purposes

DIN EN 1706:2021 铝和铝合金 铸件 化学成分和机械性能；德文版 EN 1706:2020+A1:2021

This document specifies the chemical composition limits for aluminium casting alloys and mechanical properties of separately cast test pieces for these alloys. Annex C is included as a guide to the selection of alloys for a specific use or process.This document is intended to be

Aluminium and aluminium alloys - Castings - Chemical composition and mechanical properties; German version EN 1706:2020+A1:2021

DS/EN 603-3:2021 铝和铝合金“锻造坯料”第3部分：尺寸和形状的公差

Aluminium and aluminium alloys – Wrought forging stock – Part 3: Tolerances on dimensions and form

BS EN 603-3:2021 铝及铝合金 锻件锻件 尺寸和形状公差

Aluminium and aluminium alloys. Wrought forging stock. Tolerances on dimensions and form

NF A50-922*NF EN 603-3:2021 铝及铝合金. 锻造锻坯. 第3部分: 尺寸和形状公差

Aluminium and aluminium alloys - Wrought forging stock - Part 3 : tolerances on dimensions and form

UNI EN 1706-2021 铝和铝合金 铸件 化学成分和机械性能

Aluminium and aluminium alloys - Castings - Chemical composition and mechanical properties

T/ZZB 2528-2021 新能源动力电池壳用3003铝合金板、带材

本文件规定了新能源动力电池壳用3003铝合金板、带材的产品分类、基本要求、技术要求、试验方法、检验规则、标志、包装、运输和贮存、质量承诺。 本文件适用于电动汽车、电动自行车等领域用新能源动力电池壳用3003铝合金板材（以下简称板材）、铝合金带材（以下简称带材）。

3003 Aluminum alloys plates, sheets and strips for cans of new energy power batteries

T/SZBX 038-2021 铝合金建筑型材 电泳涂漆型材

本文件规定了电泳涂漆铝合金建筑型材的术语和定义、要求、试验方法、检验规则、包装、标志、运输、贮存、质量证明书及合同（或订货单）内容。

Wrought aluminium alloy extruded profiles for architecture-Electrodeposition coating profiles

ASTM B221-21 铝和铝合金挤压棒材、棒材、线材、型材和管材的标准规范

1.1 This specification2 covers aluminum and aluminumalloy extruded bars, rods, wire, profiles, and tubes in the aluminum alloys (Note 1) and tempers shown in Table 2. NOTE 1—Throughout this specification, the use of the term alloy in the general sense includes aluminum as well as aluminum alloy. NOTE 2—For rolled or cold-finished bar and rod refer to Specification B211/B211M, for drawn seamless tube used in pressure applications, Specification B210/B210M, for structural pipe and tube, Specification B429/B429M, and for seamless pipe and tube used in pressure applications, Specification B241/B241M. NOTE 3—Pipe and tube products listed in this specification are intended for general purpose applications. This specification may not address the manufacturing processes, integrity testing, and verification required for fluid-carrying applications involving pressure. See Specifications B210/ B210M or B241/B241M, or both as appropriate, for seamless pipe and tube used in fluid-carrying applications involving pressure. See Specification B234, as appropriate, for use in surface condensers, evaporators, and heat exchangers. 1.2 Alloy and temper designations are in accordance with ANSI H35.1/H35.1M. The equivalent Unified Numbering System alloy designations are those of Table 1 preceded by A9; for example, A91100 for Aluminum 1100 in accordance with Practice E527. 1.3 For acceptance criteria for inclusion of new aluminum and aluminum alloys in this specification, see Annex A2. 1.4 A complete metric companion to Specification B221 has been developed—Specification B221M; therefore, no metric equivalents are presented in this specification. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes

ASTM B221M-21 铝和铝合金挤压棒材、棒材、线材、型材和管材的标准规范（米制）

1.1 This specification covers aluminum and aluminum-alloy extruded bars, rods, wires, profiles, and tubes in the aluminum alloys (Note 1) and tempers shown in Table 2. NOTE 1—Throughout this specification the use of the term alloy in the general sense includes aluminum as well as aluminum alloy. NOTE 2—For rolled or cold-finished bars and rods refer to Specification B211/B211M, for drawn seamless tube used in pressure applications, Specification B210/B210M, for structural pipe and tube, Specification B429/B429M, and for seamless pipe and tube used in pressure applications, Specification B241/B241M. NOTE 3— Pipe and tube products listed in this specification are intended for general purpose applications. This specification may not address the manufacturing processes, integrity testing, and verification required for fluid-carrying applications involving pressure. See Specification B210/ B210M, B241/B241M, or both as appropriate for seamless pipe and tube used in fluid-carrying applications involving pressure. See Specification B234M, as appropriate, for use in surface condensers, evaporators, and heat exchangers. 1.2 Alloy and temper designations are in accordance with ANSI H35.1/H35.1M. The equivalent Unified Numbering System alloy designations are those of Table 1 preceded by A9, for example, A91100 for Aluminum 1100 in accordance with Practice E527. 1.3 For acceptance criteria for inclusion of new aluminum and aluminum alloys in this specification, see Annex A2. 1.4 This specification is the metric counterpart of Specification B221. 1.5 The values stated in SI are to be regarded as standard. No other units of measurement are included in this specification. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes (Metric)

T/ZZB 2366-2021 商用车用铝合金车轮

本文件规定了商用车用铝合金车轮的术语和定义、基本要求、技术要求、试验方法、检验规则、标志、包装、运输、贮存、质量承诺。 本文件适用于商用车用铸造铝合金车轮（以下简称“车轮”）。

Aluminum alloy wheels for commercial vehicles