77.150.10 铝产品 标准查询与下载

KS D ISO 6363-4-2019 变形铝及铝合金冷拔棒材及管材 第4部分：拉制矩形棒材 形状和尺寸公差

Wrought aluminium and aluminium alloy cold－drawn rods/bars and tubes－Part 4：Drawn rectangular bars－Tolerances on form and dimensions

KS D ISO 7274-2019 变形铝及铝合金 拉制圆棒 形状和尺寸公差（全部减去直径公差）

Wrought aluminium and aluminium alloys－Drawn round bars－Tolerances on shape and dimensions(All minus tolerances on diameter)

KS D ISO 6363-5-2019 变形铝及铝合金冷拔棒材及管材 第5部分：拉制方形和六角形棒材 形状和尺寸公差

Wrought aluminium and aluminium alloy cold－drawn rods/bars and tubes－Part 5：Drawn square and hexagonal bars－Tolerances on form and dimensions

T/SPSTS 011-2019 锂离子电池用微孔铝箔集流体

1  范围 2  规范性引用文件 3  术语和定义 4  技术要求 5  检测方法 6  检验规则 7  检测报告 8  标志、包装、运输、贮存 9  使用说明及注意事项 附录A  质量检测报告

Current collector of micro-porous aluminium foil for lithium-ion battery

T/ZZB 1449-2019 乘用车铝制天窗导轨

本标准规定了乘用车铝制天窗导轨（以下简称天窗导轨）的术语和定义、结构示意图、基本要求、技术要求、试验方法、检验规则、标识、包装、运输、贮存、出货报告及质量承诺。 本标准适用于乘用车铝制天窗导轨。

Aluminium sunroof guide rail of passenger vehicle

ASTM B210/B210M-19a 铝和铝合金拉制无缝管的标准规范

1.1 This specification2 covers aluminum and aluminumalloy drawn seamless tubes in straight lengths and coils for general purpose and pressure applications in alloys (Note 2), tempers, and thicknesses shown in Table 2 [Table 3]. Coiled tubes are generally available only as round tubes with a wall thickness not exceeding 0.083 in. [2.00 mm] and only in non-heat-treatable alloys. 1.2 Alloy and temper designations are in accordance with ANSI H35.1/H35.1M. The equivalent Unified Numbering System alloy designations are those of Table 1 preceded by A9, for example, A91100 for aluminum designation 1100 in accordance with Practice E527. NOTE 1—See Specification B483/B483M for aluminum-alloy drawn tubes for general purpose applications; Specification B234 for aluminumalloy drawn seamless tubes for condensers and heat exchangers; and Specification B241/B241M for aluminum-alloy seamless pipe and seamless extruded tube. NOTE 2—Throughout this specification, use of the term alloy in the general sense includes aluminum as well as aluminum alloy. 1.3 For acceptance criteria for inclusion of new aluminum and aluminum alloys in this specification, see Annex A2. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes

ASTM B666/B666M-19 铝和镁制品识别标记的标准实施规程

Standard Practice for Identification Marking of Aluminum and Magnesium Products

T/ZZB 1203-2019 锂离子动力电池用铝及铝合金箔

本标准规定了锂离子动力电池用铝及铝合金箔(以下简称铝箔)的术语和定义、产品分类、基本要求、技术要求、试验方法、检验规则、标志、包装、运输、贮存和质量证明书、质量承诺。 本标准适用于锂离子动力电池集流体用铝箔，铝箔牌号为1060、 1070和1100。

Aluminium and aluminium alloy foil for lithium ion power batteries

DB53/T 938-2019 稀土镧-铸造铝合金锭

Rare earth lanthanum-cast aluminum alloy ingot

DB45/T 1990-2019 航天用2219铝合金板材技术条件

Technical conditions of 2219 aluminum alloy sheet for aerospace

ASTM B108/B108M-19 铝合金永久铸模的标准规范

1.1 This specification2 covers aluminum-alloy permanent mold castings designated as shown in Table 1. 1.2 This specification is for aluminum-alloy permanent mold castings used in general purpose applications. It may not address the mechanical properties, integrity testing, and verification required for highly loaded or safety critical applications. 1.3 Alloy and temper designations are in accordance with ANSI H35.1/H35.1(M). 1.4 Unless the order specifies the “M” specification designation, the material shall be furnished to the inch-pound units. 1.5 For acceptance criteria for inclusion of new aluminum and aluminum alloys and their properties in this specification, see Annex A1 and Annex A2. 1.6 Units—The values stated in either SI units or inchpound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Aluminum-Alloy Permanent Mold Castings

YS/T 1065.6-2019 沸石理化性能检测方法 第6部分：钙交换速率的测定 离子选择电极法

Methods for testing the physical and chemical properties of zeolites Part 6: Determination of calcium exchange rate Ion-selective electrode method

YS/T 624-2019 一般工业用铝及铝合金拉制棒材

Aluminum and aluminum alloy drawn rods for general industrial use

YS/T 1065.5-2019 沸石理化性能检测方法 第5部分：Al3+含量的测定 EDTA容量法

Methods for testing physical and chemical properties of zeolites Part 5: Determination of Al3+ content EDTA volumetric method

T/NAPA 08-2019 铝合金电泳涂漆建筑型材

本标准规定了铝合金电泳涂漆建筑型材产品的技术要求、试验方法、检验规则、标志、包装、运输、贮存与质量证明书及订货单（或合同）内容。 电泳涂漆型材产品应满足GB/T 5237.3-2017的要求，关键技术指标应达到或优于JIS H 8602-2010的要求，关键性能指标为膜厚、漆膜附着性、漆膜硬度、耐沸水性、耐碱性、耐盐雾腐蚀性、加速耐候性和紫外盐雾联合试验。

Aluminum alloy electrophoresis painted architectural profiles

T/NAPA 09-2019 铝合金喷粉建筑型材

本标准规定了铝合金喷粉建筑型材产品的技术要求、试验方法、检验规则、标志、包装、运输、贮存与质量证明书及订货单（或合同）内容。 喷粉型材产品应满足GB/T 5237.4-2017的要求，关键技术指标应达到或优于EN 12206-1-2004的要求，关键性能指标为膜层厚度、附着性、耐冲击性、耐砂浆性、耐沸水性、耐盐雾腐蚀性、耐丝状腐蚀性、耐湿热性、自然耐候性、加速耐候性。

Aluminum alloy powder sprayed building profiles

T/NAPA 07-2019 铝合金阳极氧化建筑型材

本标准规定了铝合金阳极氧化建筑型材产品的技术要求、试验方法、检验规则、标志、包装、运输、贮存与质量证明书及订货单（或合同）内容。     阳极氧化型材产品应满足GB/T 5237.2-2017的要求，关键技术指标应达到或优于JIS H 8401-1999的要求。关键性能指标为氧化默默猴、封孔质量、耐盐雾腐蚀、耐磨性。

Aluminum alloy anodized building profiles

T/NAPA 10-2019 铝合金喷漆建筑型材

本标准规定了铝合金喷漆建筑型材产品的技术要求、试验方法、检验规则、标志、包装、运输、贮存与质量证明书及订货单（或合同）内容。 喷漆型材产品应满足GB/T 5237.5-2017的要求，关键技术指标应达到或优于AAMA 2605-2011的要求，关键性能指标为膜层厚度、附着性、耐沸水性、耐盐雾腐蚀性、耐湿热性、自然耐候性、加速耐候性。

Aluminum Alloy Painted Architectural Profiles

DB13/T 5014-2019 铝板拉伸装饰网通用技术要求

General Technical Requirements for Aluminum Stretched Decorative Mesh

DB13/T 5015-2019 铝窗纱通用技术要求

General Technical Requirements for Aluminum Window Screens