77.150.10 铝产品 标准查询与下载

EN 16914:2017 铝及铝合金热轧钢板可焊铝合金的交货技术条件

This European Standard specifies the technical delivery conditions relating to armour plates in weldable aluminium alloy with a nominal thickness between 10 mm and 70 mm. For thickness below 10 mm, other specifications may be applied.

Aluminium and aluminium alloys - Hot-rolled armour plates in weldable aluminium alloy - Technical delivery conditions

DIN EN 754-2:2017 铝和铝合金.冷拉杆材/棒材和管材.第2部分:机械特性.德文版本EN 754-2-2016

Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 2: Mechanical properties; German version EN 754-2:2016

GOST R 57511-2017 铝合金开式和闭式模锻件 缺陷的术语和定义

Aluminium alloy open and closed die forgings. Terms and definitions of defects

GOST R 57517-2017 通用铝及铝合金拉丝 规格

General-purpose aluminium and aluminium alloys drawn wire. Specifications

GOST R 57510-2017 铝合金轧制产品. 缺陷术语和定义

Aluminium alloy rolled products. Terms and definitions of defects

ASTM B179-17 铸造用铝合金原锭及熔融锭在各铸造过程的标准规格

1.1 This specification covers commercial aluminum alloys in ingot form for remelting and molten form for the manufacture of castings. The specific gravity of these alloys does not exceed 3.0 and they are designated as shown in Table 1. Note 1: Throughout this specification the use of “ingot” in a general sense includes sow, T-bar, T-ingot, and pig. 1.2 Alloy designations are in accordance with ANSI H35.1/H35.1(M). Note 2: Supplementary data pertaining to the alloys covered by this specification when used in the form of castings are given in Specifications B26/B26M, B85/B85M, B108/B108M, B618/B618M, B686/B686M, B955/B955M, and B969/B969M. 1.3 Unless the order specifies the “M” specification designation, the material shall be furnished to the inch-pound units. 1.4 For acceptance criteria for inclusion of new aluminum and aluminum alloys in this specification, see Annex A1. 1.5 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Aluminum Alloys in Ingot and Molten Forms for Castings from All Casting Processes

ASTM B969/B969M-17 用模压铸造, 触变铸造和流变铸造半固体铸件法生产的铝合金铸件的标准规格

1.1 This specification covers aluminum-alloy castings, produced by the thixocast, rheocast, semi-solid, and squeeze casting processes shown in Table 1. (A) When single units are shown, they indicate the maximum amounts permitted.(B) Analysis shall be made for the elements for which limits are shown in this table.(C) The following applies to all specified limits in this table: For purposes of determining conformance to these limits, an observed value or a calculated value obtained from analysis shall be rounded to the nearest unit in the last right-hand place of figures used in expressing the specified limit in accordance with the rounding-off method of Practice E29.(D) In case of discrepancy between the values listed in Table 1 and those listed in the “œDesignations and Composition Limits for Aluminum Alloys in the Form of Castings and Ingot (known as the “œPink Sheets”)”€œ, the composition limits registered with the Aluminum Association and published in the “œPink Sheets” shall be considered the controlling composition.(E) “Others” includes listed elements for which no specific limit is shown as well as unlisted metallic elements. The producer may analyze samples for trace elements not specified in the specification. However, such analysis is not required and may not cover all metallic “Others” elements. Should any analysis by the producer or the purchaser establish that an “Others” element exceeds the limit of “Each” or that the aggregate of several “Others” elements exceeds the limit of “Total,” the material shall be considered nonconforming.(F) Other Elements—Total shall be the sum of unspecified metallic elements 0.0108201;% or more, rounded to the second decimal before determining the sum.(G) If iron exceeds 0.45, manganese content shall not be less than one-half iron content.(H) The Aluminum Association ruling on the number of decimal places to which Mg percent is expressed is exempted for some long standing alloys. See A2.2.6.(I) For a cross reference of current and former alloy designations see the Aluminum Association’€™s “Designations and Chemical Composition Limits for Aluminum Alloys in the Form of Castings and Ingot (The Pink Sheets)”.

Standard Specification for Aluminum-Alloy Castings Produced by Squeeze Casting, Thixocast and Rheocast Semi-Solid Casting Processes

ASTM B234M-17 表面冷凝器, 蒸发器和热交换器用铝和铝合金拉制无缝管的标准规格(米制)

1.1 This specification covers aluminum-alloy (Note 1) drawn seamless round tube in straight lengths designated as shown in the Table 2, for use in surface condensers, evaporators, and heat exchangers. Note 1: Throughout this specification use of the term alloy in the general sense includes aluminum as well as aluminum alloy. Note 2: For drawn seamless tubes used in general applications, see Specifications B210 and B210M; for extruded tubes see Specifications B221 and B221M; for seamless pipe and seamless extruded tube used in pressure applications, see Specification B241/B241M; and for structural pipe and tube see Specification B429/B429M. (A) Limits are in percent maximum unless shown as a range or otherwise stated.(B) Analysis shall be made for the elements for which limits are shown in this table.(C) For purposes of determining conformance to these limits, an observed value or a calculated value attained from analysis shall be rounded to the nearest unit in the last right-hand place of figures used in expressing the specified limit, in accordance with the rounding-off method of Practice E29.(D) Others includes listed elements for which no specific limit is shown as well as unlisted metallic elements. The producer may analyze samples for trace elements not specified in this specification. However, such analysis is not required and may not cover all metallic Others elements. Should any analysis by the producer or the purchaser establish that an Others element exceeds the limit of Each or that the aggregate of several Others elements exceeds the limit of Total, the material shall be considered nonconforming.(E) Other Elements—Total shall be the sum of unspecified metal

Standard Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes for Surface Condensers, Evaporators, and Heat Exchangers (Metric)

ASTM E2422-17 用于铝铸件检测的标准0716数cb5f字参考图像

1.1 These digital reference images illustrate the types and degrees of discontinuities that may be found in aluminum-alloy castings. The castings illustrated are in thicknesses of 1⁄4 in. (6.35 mm) and 3⁄4 in. (19.1 mm). 1.2 All areas of this standard may be open to agreement between the cognizant engineering organization and the supplier, or specific direction from the cognizant engineering organization. These items should be addressed in the purchase order or the contract. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 These digital reference images are not intended to illustrate the types and degrees of discontinuities found in aluminum-alloy castings when performing film radiography. If performing film radiography of aluminum-alloy castings, refer to Reference Radiographs E155. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 Only licensed copies of the software and images shall be utilized for production inspection. A copy of the ASTM/User license agreement shall be kept on file for audit purposes. NOTE 1—The set of digital reference images consists of 13 digital files, software to load the desired format and specific instructions on the loading process. The 13 reference images illustrate eight grades of severity and contain an image of a step wedge and two line pair gauges. Available from ASTM International Headquarters, Order No: RRE02422. Refer to Practice E2002 for line pair gauge details. NOTE 2—Reference radiographs applicable to aluminum and magnesium die castings up to 1 in. (25 mm) in thickness are contained in Reference Radiographs E505. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Digital Reference Images for Inspection of Aluminum Castings

ASTM B234-17 表面冷凝器, 蒸发器和热交换器用铝和铝合金拉制无缝管的标准规格

1.1 This specification2 covers aluminum-alloy (Note 1) drawn seamless round tube in straight lengths designated as shown in Table 2, for use in surface condensers, evaporators, and heat exchangers. Note 1: Throughout this specification use of the term alloy in the general sense includes aluminum as well as aluminum alloy. Note 2: For drawn seamless tubes used in general applications, see Specifications B210 and B210M; for extruded tubes see Specifications B221 and B221M; for seamless pipe and seamless extruded tube used in pressure applications see Specification B241/B241M; and for structural pipe and tube see Specification B429/B429M. (A) Limits are in percent maximum unless shown as a range or otherwise stated.(B) Analysis shall be made for the elements for which limits are shown in this table.(C) For purposes of determining conformance to these limits, an observed value or a calculated value attained from analysis shall be rounded to the nearest unit in the last right-hand place of figures used in expressing the specified limit, in accordance with the rounding-off method of Practice E29.(D) Others includes listed elements for which no specific limit is shown as well as unlisted metallic elements. The producer may analyze samples for trace elements not specified in this specification. However, such analysis is not required and may not cover all metallic Others elements. Should any analysis by the producer or the purchaser establish that an Others element exceeds the limit of Each or that the aggregate of several Others elements exceeds the limit of Total, the material shall be considered nonconforming.(E) Other Elements—

Standard Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes for Surface Condensers, Evaporators, and Heat Exchangers

BS EN 12020-2:2016 铝及铝合金.合金EN AW-6060和EN AW-6063挤压的精密型材:尺寸和形状公差

Aluminium and aluminium alloys. Extruded precision profiles in alloys EN AW-6060 and EN AW-6063. Tolerances on dimensions and form

GSO ISO 6362-7:2016 变形铝和铝合金 挤压棒材、管材和型材 第7部分：化学成分

This part of ISO 6362 specifies the chemical composition of wrought aluminium and aluminium alloys. The chemical composition limits of aluminium and aluminium alloys specified herein are completely identical with those registered with the Aluminium Association, 1525 Wilson Boulevard, Suite 600, Arlington, VA 22209, USA (known as the “Teal Sheets”), for the corresponding alloys. NOTE In the case of a discrepancy in the values listed in Table 1 with those listed in the “Registration Record Series Teal Sheets, International Alloy Destinations and Chemical Composition Limits for Wrought Aluminum and Wrought Aluminum Alloys”, the composition limits registered with the Aluminium Association and published in the “Teal Sheets” can be considered for controlling the composition.

Wrought aluminium and aluminium alloys -- Extruded rods/bars, tubes and profiles -- Part 7: Chemical composition

GSO ISO 6362-6:2016 变形铝和铝合金 挤压棒材、管材和型材 第6部分：圆形、方形、矩形和六角形管 形状和尺寸公差

This part of ISO 6362 specifies the tolerances on dimensions and shape of wrought aluminium and aluminium alloy extruded round bars having diameters in the range from 8 mm up to 350 mm; and square and hexagonal bars having widths across flats in the range from 10 mm up to 220 mm. It applies to extruded round, square and hexagonal bars.

Wrought aluminium and aluminium alloys -- Extruded rods/bars, tubes and profiles -- Part 6: Round, square, rectangular and hexagonal tubes -- Tolerances on shape and dimensions

EN 12020-2:2016 铝及铝合金.合金EN AW-6060和EN AW-6063挤压的精密型材尺寸和形状公差

This European Standard specifies tolerances on dimensions and form of extruded precision profiles, in alloys EN AW-6060 and EN AW-6063 manufactured with and without a thermal barrier. It applies to extruded products supplied without further surface treatment. Precision profiles covered in this standard are distinguished from extruded profiles for general applications covered in EN 755-9 by the following characteristics: - they are mainly for architectural applications; - they meet more stringent requirements regarding the surface condition of visible surfaces; - the maximum diameter of the circumscribing circle CD is 350 mm; - they are made to closer tolerances on dimensions and form. In the case of profiles which, due to the complexity of their design, are difficult to manufacture and specify, then special agreements between supplier and purchaser may need to be reached. NOTE The effect of the thermal barrier material on the dimensional tolerances is covered by this document although the actual thermal barrier material itself is not (see EN 14024).

Aluminium and aluminium alloys - Extruded precision profiles in alloys EN AW-6060 and EN AW-6063 - Part 2: Tolerances on dimensions and form

BS EN 754-2:2016 铝及铝合金 冷拔棒/棒和管 机械性能

Aluminium and aluminium alloys. Cold drawn rod/bar and tube. Mechanical properties

EN 754-2:2016 铝及铝合金-冷拔棒材条材和管材-第2部分:力学性能

This European Standard specifies the mechanical property limits resulting from tensile testing applicable to aluminium and aluminium alloy cold drawn rod/bar and tube. Technical conditions for inspection and delivery, including product and testing requirements, are specified in EN 754-1. Temper designations are defined in EN 515. The chemical composition limits for these materials are given in EN 573-3.

Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 2: Mechanical properties

DIN EN 754-8:2016 铝和铝合金.冷拉杆材/棒材和管材.第8部分:带孔管材的尺寸和形状公差.德文版本EN 754-8-2016

Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 8: Porthole tubes, tolerances on dimensions and form; German version EN 754-8:2016

DIN EN 755-9:2016 铝和铝合金.挤压杆材/棒材、管材和型材.第9部分:轮廓、尺寸和形状公差.德文版本EN 755-9-2016

Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 9: Profiles, tolerances on dimensions and form; German version EN 755-9:2016

DIN EN 754-7:2016 铝和铝合金.冷拉杆材/棒材和管材.第7部分:无缝管的尺寸和形状公差.德文版本EN 754-7-2016

Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 7: Seamless tubes, tolerances on dimensions and form; German version EN 754-7:2016

DIN EN 755-8:2016 铝和铝合金.挤压杆材/棒材、管材和型材.第8部分:带孔管材的尺寸和形状公差.德文版本EN 755-8-2016

Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 8: Porthole tubes, tolerances on dimensions and form; German version EN 755-8:2016