77.150.10 铝产品 标准查询与下载

GSO ISO 3522:2015 铝及铝合金铸件化学成分和机械性能

This International Standard specifies the chemical composition limits for aluminium casting alloys and mechanical properties of separately cast test bars for these alloys.

Aluminium and aluminium alloys -- Castings -- Chemical composition and mechanical properties

T/ZZB 012-2015 汽车铝合金车轮

本标准规定了汽车铝合金车轮术语和定义、基本要求、技术要求、试验方法、检验规则、标志、包装、运输和贮存要求。 本标准适用于乘用车用铸造铝合金车轮。

Aluminum alloy auto wheel

LST EN 1559-4-2015 铸造. 技术交货条件. 第4部分: 锌合金铸件的补充要求

Founding - Technical conditions of delivery - Part 4: Additional requirements for aluminium alloy castings

DIN EN 1396:2015 铝和铝合金.普通绕涂板材和带材.规范;德文版本EN 1396-2015

Aluminium and aluminium alloys - Coil coated sheet and strip for general applications - Specifications; German version EN 1396:2015

NF A50-432*NF EN 1396:2015 铝和铝合金.通用彩色涂层的薄板材和带材.规范

Aluminium and aluminium alloys - Coil coated sheet and strip for general applications - Specifications

DIN EN 1559-4:2015 铸造.交货技术条件.第4部分:铝合金铸件的附加要求;德文版本EN 1559-4-2015

Founding - Technical conditions of delivery - Part 4: Additional requirements for aluminium alloy castings; German version EN 1559-4:2015

YS/T 1088-2015 湿法冶金锌电积用阴极板

本标准规定了湿法冶金锌电积用阴极板(以下简称为“阴极板”)产品的术语和定义、要求、试验方法、检验规则与包装、标志、运输、贮存及质量证明书与订货单(或合同)内容。 本标准适用于以双零铝合金板材为基本材料，经焊接与组装加工而成用于湿法冶金锌电积用的阴极板。

Cathode plate for zinc electrowinning in hydrometallurgy

BS EN 1396:2015 铝和铝合金.通用卷绕涂层薄板材和带材.规范

Aluminium and aluminium alloys. Coil coated sheet and strip for general applications. Specifications

YS/T 95.1-2015 空调器散热片用铝箔 第1部分 基材

Aluminum foil for air conditioner radiator part 1 base material

NF A00-500-4*NF EN 1559-4:2015 铸造.交货技术条件.第4部分:铝合金铸件的附加要求

Founding - Technical conditions of delivery - Part 4 : additional requirements for aluminium alloy castings

YS/T 1037-2015 铝箔生产用铝管芯

本标准规定了铝箔生产用铝管芯的要求、试验方法、检验规则和标志、包装、运输、贮存及质量证明书与订货单(或合同)内容。 本标准适用于铝箔生产用铝管芯(以下简称管芯)。

Aluminium alloy pipe core used in the producing of aluminium and aluminium alloy foil

EN 1396:2015 铝及铝合金.卷材和带材的一般用途.分类

This European Standard specifies the particular requirements for wrought aluminium and wrought aluminium alloys in the form of coil coated sheet and strip for general applications. This product is generally supplied in thicknesses up to 3,0 mm. It applies to cold-rolled aluminium and aluminium alloy strip coated by the coil coating process both with liquid as well as with powder paints, either in the final width or slit afterwards, and to sheet obtained from such strip. It does not apply to coil coated sheet and strip used for special applications such as cans, closures and lids which are dealt with in separate EN 541.

Aluminium and aluminium alloys - Coil coated sheet and strip for general applications - Specifications

BS EN 1559-4:2015 创立 交货技术条件 铝合金铸件的附加要求

Founding. Technical conditions of delivery. Additional requirements for aluminium alloy castings

EN 1559-4:2015 铸造.交货技术条件.第2部分：钢铸件的附加要求

This European Standard specifies the additional technical delivery conditions for aluminium alloy castings unless other conditions have been agreed at the time of enquiry and order. This European Standard retains the same structure and numbering system as used in EN 1559-1 and repeats the numbering of clauses and sub-clauses even if nothing extra or different has been added. It also indicates items specific to aluminium alloy castings under existing or new headings.

Founding - Technical conditions of delivery - Part 4: Additional requirements for aluminium alloy castings

ASTM B557-15 锻造和铸造的铝及镁合金制品抗拉试验的标准试验方法

4.1 Tension tests provide information on the strength and ductility of materials under uniaxial tensile stresses. This information may be useful in comparisons of materials, alloy development, quality control, and design under certain circumstances. 4.2 The results of tension tests of specimens machined to standardized dimensions from selected portions of a part or material may not totally represent the strength and ductility properties of the entire end product or its in-service behavior in different environments. 4.3 These test methods are considered satisfactory for acceptance testing of commercial shipments and have been used extensively in the trade for this purpose. 1.1 These test methods cover the tension testing of wrought and cast aluminum- and magnesium-alloy products, with the exception of aluminum foil,2 and are derived from Test Methods E8, which cover the tension testing of all metallic materials. 1.2 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 1: Foil is sheet metal less than 0.00798201;in. thick. There is an overlap in the thickness range 0.006 to 0.00798201;in. defined for foil and sheet. Sheet products in this thickness range are supplied to sheet product specifications and foil products in this thickness range are supplied to foil product specifications. Exceptions to the provisions of these test methods may need to be made in individual specifications or test methods for a particular material. Note 2: A complete metric companion to Test Methods B557 has been developed—Test Methods B557M; therefore, no metric equivalents are presented in these test methods.

Standard Test Methods for Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products

GOST R 56371-2015 造船用铝合金薄板. 规格

Aluminium alloy sheets for shipbuilding. Specifications

ASTM B557M-15 锻造和铸造的铝及镁合金制品抗拉试验的标准试验方法 (米制)

4.1 Tension tests provide information on the strength and ductility of materials under uniaxial tensile stresses. This information may be useful in comparisons of materials, alloy development, quality control, and design under certain circumstances. 4.2 The results of tension tests of specimens machined to standardized dimensions from selected portions of a part or material may not totally represent the strength and ductility properties of the entire end product or its in-service behavior in different environments. 4.3 These test methods are considered satisfactory for acceptance testing of commercial shipments and have been used extensively in the trade for this purpose. 1.1 These test methods cover the tension testing of wrought and cast aluminum- and magnesium-alloy products, with the exception of aluminum foil,2 and are derived from Test Methods E8M, which cover the tension testing of all metallic materials. Note 1: These metric test methods are the equivalents of those in Test Methods B557, and are compatible in technical content except for the requirement of longer gage lengths for round specimens. Note 2: Foil is sheet metal less than 0.20 mm thick. There is an overlap in the thickness range 0.15 to 0.20 mm defined for foil and sheet. Sheet products in this thickness range are supplied to sheet product specifications and foil products in this thickness range are supplied to foil product specifications. Exceptions to the provisions of these test methods may need to be made in individual specifications or test methods for a particular material. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products (Metric)

ASTM B247M-15 铝和铝合金模锻件, 手持式锻件以及滚环锻件的标准规格 (米制)

1.1 This specification covers aluminum-alloy (Note 1) die forgings, hand forgings, and rolled ring forgings as shown in Tables 2-4 and in Section 10 for heat-treatable alloy forgings supplied in the F and 01 tempers. The maximum thicknesses for forgings within the scope of this specification are as indicated in those tables. Note 1: Throughout this specification use of the term alloy in the general sense includes aluminum as well as aluminum alloy. Note 2: For forging stock supplied as rolled or cold-finished bar or rod see Specification B211M. For forging stock supplied as extruded bar or rod see Specification B221M. (A) Limits are in mass percent maximum unless shown as a range or stated otherwise.(B) Analysis shall be made for the elements for which limits are shown in this table.(C) For purposes of determining conformance to these limits, an observed value or a calculated value obtained from analysis shall be rounded to the nearest unit in the last right-hand place of figures used in expressing the specified limit, in accordance with the rounding-off method of Practice E29.(D) Others includes listed elements for which no specific limit is shown as well as unlisted metallic elements. The producer may analyze samples for trace elements not specified in the specification. However, such analysis is not required and may not cover all metallic Others elements. Should any analysis by the producer or the purchaser establish that an Others element exceeds the limit of Each or that the aggregate of several Others elements exceeds the limit of Total, the material shall be considered nonconforming.(E) Other Elements—Total shall be the sum of unspecified metallic elements 0.0108201;% or more, rounded to the second decimal before determining the sum.

Standard Specification for Aluminum and Aluminum-Alloy Die Forgings, Hand Forgings, and Rolled Ring Forgings (Metric)

ASTM B666/B666M-15 用于铝和镁产品的识别标记的标准实施规程

1.1 This practice establishes the physical item marking requirements for identification purposes for aluminum and magnesium products. Package marking for shipment and inspection acceptance is not within the scope of this standard. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Identification Marking of Aluminum and Magnesium Products

ASTM B632/B632M-15 铝合金冷轧板的标准规格

1.1 This specification covers aluminum-alloy rolled flat tread plate, mill-finish, with a raised pattern on one side, in the alloy, tempers, and thicknesses shown in Table 1 and Table 2 [Table 3]. (A) Limits in weight percent maximum unless shown as a range or minimum(B) Analysis shall be made for the elements for which limits are shown in this table.(C) For purposes of determining conformance to these limits, an observed value or a calculated value obtained from analysis shall be rounded to the nearest unit in the last right-hand place of figures used in expressing the specified limit, in accordance with the rounding off method of Practice E29.(D) Others includes listed elements for which no specific limit is shown as well as unlisted metallic elements. The producer may analyze samples for trace elements not specified in the specification. However, such analysis is not required and may not cover all metallic Others elements. Should any analysis by the producer or purchaser establish that an Others element exceed the limit of Each or that the aggregate of several Others elements exceeds the limit of Total, the material shall be considered non-conforming.(E) Other Elements—Total shall be the sum of unspecified metallic elements 0.0108201;% or more, rounded to the second decimal before determining the sum.(F) In case there is a discrepancy in the values listed in Table 1 with those listed in the “International Alloy Designations and Chemical Composition Limits for Wrought Aluminum and Wrought Aluminum Alloys” (known as the “Teal Sheets”), the composition limits registered with the Aluminum Association and published in the “Teal Sheets” shall be considered the controlling composition. The “Teal Sheets” are available at http://www.aluminum.org/tealsheets. (A) To determine conformance to this specification, each value for tensile strength and for yield strength shall be rounded to the nearest 0.1 ksi and each value for elongation to the nearest 0.58201;%, both in accordance with the rounding-off method of Practice E29.(B) 

Standard Specification for Aluminum-Alloy Rolled Tread Plate