77.150.10 (Aluminium products) 标准查询与下载

ASTM E1976-05 不可膨胀战术掩体的标准规范

1.1 This specification covers a rigid wall, nonexpandable shelter constructed of aluminum-faced, nonmetallic honeycomb sandwich panels, and meeting the International Organization for Standardization (ISO) Cargo Container specification. Nominal dimensions are: height 8 ft, width 8 ft and length 20 ft (2.4 by 2.4 by 6.1 m).1.2 The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information only.1.3 The following precautionary statement pertains to the test method portion only, Section 7, of this specification: This statement does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Shelter, Tactical, Nonexpandable

ASTM B221-05a 铝和铝合金挤制棒材、条材、线材、型材和管材的标准规范

1.1 This specification covers aluminum and aluminum-alloy extruded bar, rod, wire, profile, and tube in the aluminum alloys (Note 1) and tempers shown in Table 2. Note 18212;Throughout this specification, the use of the term alloy in the general sense includes aluminum as well as aluminum alloy.Note 28212;For rolled or cold-finished bar and rod refer to Specification B 211, for drawn tube, Specification B 210, for structural pipe and tube, Specification B 429, and for seamless pipe and tube, Specification B 241/B 241M. 1.2 Alloy and temper designations are in accordance with ANSI H35.1. The equivalent Unified Numbering System alloy designations are those of Table 1 preceded by A9; for example, A91100 for Aluminum 1100 in accordance with Practice E 527.1.3 For acceptance criteria for inclusion of new aluminum and aluminum alloys in this specification, see Annex A2.1.4 A complete metric companion to B 221 has been developed-B 221M; therefore, no metric equivalents are presented in this specification.

Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes

ASTM B941-05 电工用耐热铝锆合金丝的标准规范

1.1 This specification covers heat resistant aluminum-zirconium alloy round wire for electrical purposes. There is a family of aluminum-zirconium alloys that are used for heat-resistance (i.e. resist annealing), which differ by zirconium content, tensile strength, electrical conductivity, and maximum use temperature. This standard covers one currently commercially applicable alloy from this family.1.2 The values stated in inch-pound units are standard. The SI equivalents of inch-pound units may be approximate.

Standard Specification for Heat Resistant Aluminum-Zirconium Alloy Wire for Electrical Purposes

ASTM B210-04 拉制无缝铝和铝合金管的标准规范

1.1 This specification covers aluminum and aluminum-alloy drawn seamless tubes in straight lengths and coils for general purpose and pressure applications in alloys (Note 0), tempers, and thicknesses shown in . Coiled tubes are generally available only as round tubes with a wall thickness not exceeding 0.083 in. and only in nonheat-treatable alloys.1.2 Alloy and temper designations are in accordance with ANSI H35.1. The equivalent Unified Numbering System alloy designations are those of preceded by A9, for example, A91100 for aluminum designation 1100 in accordance with Practice E 527. Note 2See Specification B 483 for aluminum-alloy drawn tubes for general purpose applications; Specification B 234 for aluminum-alloy drawn seamless tubes for condensers and heat exchangers; and Specification B 241/B 241M for aluminum-alloy seamless pipe and seamless extruded tube.Note 0Throughout this specification, use of the term alloyin the general sense includes aluminum as well as aluminum alloy.1.3 A complete metric companion to Specification B 210 has been developed-Specification B 210M; therefore, no metric equivalents are presented in this specification.1.4 For acceptance criteria for inclusion of new aluminum and aluminum alloys in this specification, see . 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes

ASTM B234M-04 冷凝器及热交换器用铝和铝合金拉制无缝管的标准规范(米制)

1.1 This specification covers aluminum-alloy (Note 0) drawn seamless round tube in straight lengths designated as shown in the , for use in surface condensers, evaporators, and heat exchangers. Note 0Throughout this specification use of the term alloy in the general sense includes aluminum as well as aluminum alloy.Note 2For drawn seamless tubes used in general applications, see Specification B 210M; for extruded tubes see Specification B 221M; for seamless pipe see Specification B 241/B 241M; and for structural pipe and tube see Specification B 429.Note 3This specification is the metric counterpart of Specification B 234.1.2 Alloy and temper designations are in accordance with ANSI H35.1M. The equivalent Unified Numbering System alloy designations are those of preceded by , for example, A91060 for aluminum 1060, in accordance with Practice E 527.1.3 For acceptance criteria for inclusion of new aluminum and aluminum alloys in this specification, see .1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes for Condensers and Heat Exchangers [Metric]

ASTM B209-04 铝和铝合金薄板和中厚板标准规范

1.1 This specification covers aluminum and aluminum-alloy flat sheet, coiled sheet, and plate in the alloys (Note 1) and tempers shown in Tables 2and 3, and in the following finishes: 1.1.1 Plate in all alloys and sheet in heat-treatable alloys: mill finish.1.1.2 Sheet in nonheat-treatable alloys: mill finish, one-side bright mill finish, standard one-side bright finish, and standard two-sides bright finish. Note 18212;Throughout this specification, use of the term alloyin the general sense includes aluminum as well as aluminum alloy.Note 28212;See Specification B 632/B 632M for tread plate.Note 38212;See Specification B 928/B 928M for marine sheet and plate. Due to additional corrosion testing required, it is not intended that Specification B 209 be used for marine sheet and plate.1.2 Alloy and temper designations are in accordance with ANSI H35.1. The equivalent Unified Numbering System alloy designations are those of preceded by A9, for example, A91100 for aluminum 1100 in accordance with Practice E 527.1.3 A complete metric companion to Specification B 209 has been developed-Specification B 209M; therefore, no metric equivalents are presented in this specification.1.4 For acceptance criteria for inclusion of new aluminum and aluminum alloys in this specification, see .

Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate

ASTM B221-04a 铝和铝合金挤压棒材、棒材、线材、型材和管材的标准规范（米制）

1.1 This specification covers aluminum and aluminum-alloy extruded bar, rod, wire, profile, and tube in the aluminum alloys (Note 0) and tempers shown in Tabld 2. Note 18212;Throughout this specification, the use of the term alloy in the general sense includes aluminum as well as aluminum alloy.Note 28212;For rolled or cold-finished bar and rod refer to Specification B 211, for drawn tube, Specification B 210, for structural pipe and tube, Specification B 429, and for seamless pipe and tube, Specification B 241/B 241M. 1.2 Alloy and temper designations are in accordance with ANSI H35.1. The equivalent Unified Numbering System alloy designations are those of preceded by A9; for example, A91100 for Aluminum 1100 in accordance with Practice E 527.1.3 For acceptance criteria for inclusion of new aluminum and aluminum alloys in this specification, see .1.4 A complete metric companion to B 221 has been developed-B 221M; therefore, no metric equivalents are presented in this specification.

Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes

ASTM E1976-04 可长期使用的战术掩体的标准规范

1.1 This specification covers a rigid wall, nonexpandable shelter constructed of aluminum-faced, nonmetallic honeycomb sandwich panels, and meeting the International Organization for Standardization (ISO) Cargo Container specification. Nominal dimensions are: height 8 ft, width 8 ft and length 20 ft (2.4 by 2.4 by 6.1 m).1.2 The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information only.1.3 The following precautionary statement pertains to the test method portion only, Section 7, of this specification: This statement does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Shelter, Tactical, Nonexpandable

ASTM B234-04 冷凝器及热交换器用铝和铝合金拉制无缝管的标准规范

1.1 This specification covers aluminum-alloy (Note 1) drawn seamless round tube in straight lengths designated as shown in Table 2, for use in surface condensers, evaporators, and heat exchangers. Note 1 Throughout this specification use of the term alloy in the general sense includes aluminum as well as aluminum alloy.Note 2For drawn seamless tubes used in general applications, see Specification B 210; for extruded tubes see Specification B 221; for seamless pipe see Specification B 241/B 241M; and for structural pipe and tube see Specification B 429.1.2 Alloy and temper designations are in accordance with ANSI H35.1. The equivalent Unified Numbering System alloy designations are those of preceded by A9, for example, A91060 for aluminum 1060, in accordance with Practice E 527.1.3 A complete metric companion to Specification B 234 has been developed-B 234M; therefore, no metric equivalents are presented in this specification.1.4 For acceptance criteria for inclusion of new aluminum and aluminum alloys in this specification, see .1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes for Condensers and Heat Exchangers

ASTM E1978-04 可长期使用的双面战术掩体的标准规范

1.1 This specification covers a rigid wall, two-side expandable shelter constructed of aluminum-faced, nonmetallic honeycomb sandwich panels and meeting the International Organization for Standardization (ISO) cargo container specification in the transport mode. Nominal dimensions when closed (container mode) are: height 8 ft, width 8 ft, and length 20 ft (2.4 by 2.4 by 6.1 m). Approximate dimensions when expanded (shelter mode) are: height 8 ft, width 22 ft, and length 20 ft (2.4 by 6.7 by 6.1 m).1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Shelter, Tactical, Expandable, Two-Side

ASTM B221M-04 铝和铝合金挤制棒材、条材、线材、型材和管材(米制)标准规范

1.1 This specification covers aluminum and aluminum-alloy extruded bar, rod, wire, profile, and tube in the aluminum alloys (Note 1) and tempers shown in Table 2. Throughout this specification the use of the term alloy in the general sense includes aluminum as well as aluminum alloy.Note 1For rolled or cold-finished bars and rods refer to Specification B 211M, for drawn tube, Specification B 210M, for structural pipe and tube, Specification B 429M, and for seamless pipe and tube, Specification B 241/B 241M. 1.2 Alloy and temper designations are in accordance with ANSI H35.1M. The equivalent Unified Numbering System alloy designations are those of preceded by A9, for example, A91100 for Aluminum 1100 in accordance with Practice E 527.1.3 For acceptance criteria for inclusion of new aluminum and aluminum alloys in this specification, see .1.4 This specification is the metric counterpart of Specification B 221.1.5 The values stated in SI are to be regarded as standard. No other units of measurement are included in this specification.

Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes [Metric]

ASTM E1977-04 可长期使用的单面战术掩体的标准规范

1.1 This specification covers a rigid wall, one-side expandable shelter constructed of aluminum-faced, nonmetallic honeycomb sandwich panels, and meeting the International Organization for Standardization (ISO) Cargo Container specification in the transport mode. Nominal dimensions when closed (container mode) are: height 8 ft, width 8 ft and length 20 ft (2.4 by 2.4 by 6.1 m). Approximate dimensions, when expanded (shelter mode) are: height 8 ft, width 15 ft and length 20 ft (2.4 by 4.6 by 6.1 m). 1.2 The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information only. 1.3 The following precautionary statement pertains to the test method portion only, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Shelter, Tactical, Expandable, One-Side

ASTM B85-03 铝合金压模铸件标准规范

1.1 This specification covers aluminum-alloy die castings of all compositions. Thirteen of the most commonly die cast alloy compositions are specified, designated as shown in Table 1.1.2 Alloy and temper designations are in accordance with ANSI H35.1. The equivalent unified numbering system alloy designations are in accordance with Practice E 527.1.3 For acceptance criteria for inclusion of new aluminum and aluminum alloys and their properties in this specification, see Annex A1 and Annex A2.1.4 Units8212;The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are mathematical conversions to SI units which are provided for information only and are not considered standard.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

Standard Specification for Aluminum-Alloy Die Castings

ASTM B686-03 高强度铝合金铸件标准规范

1.1 This specification covers aluminum-alloy high-strength castings designated as shown in Table 1. 1.2 Castings covered by this specification are intended for use in airframe, missile, and other critical applications where high strength, ductility, and sound castings are required.1.3 For acceptance criteria for inclusion of new aluminum and aluminum alloys and their properties in this specification, see Annex A1 and Annex A1.1.4 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regular limitations prior to use.

Standard Specification for Aluminum Alloy Castings, High-Strength

ASTM B179-03 铸造工艺用的铝合金铸锭和熔融成形铸件的标准规范

1.1 This specification covers commercial aluminum alloys in ingot form for remelting and molten form for the manufacture of castings. The specific gravity of these alloys does not exceed 3.0 and they are designated as shown in Tables 1 and 2. Note 18212;Throughout this specification the use of "ingot" in a general sense includes sow, T-bar, T-ingot, and pig.1.2 Alloy designations are in accordance with ANSI H35.1. The equivalent Unified Numbering System alloy designations are in accordance with Practice E 527. Note 28212;Supplementary data pertaining to the alloys covered by this specification when used in the form of castings are given in Specifications B 26/B 26M, B 85, B 108, B 618, and B 686.1.3 For acceptance criteria for inclusion of new aluminum and aluminum alloys in this specification, see Annex A1.1.4 The values stated in inch-pound units are to be regarded as the standard.

Standard Specification for Aluminum Alloys in Ingot and Molten Forms for Castings from All Casting Processes

ASTM B108-03a 铝合金永久铸模的标准规范

1.1 This specification covers aluminum-alloy permanent mold castings designated as shown in Table 1.1.2 This specification is not intended for aluminum-alloy permanent mold castings used in aerospace applications.1.3 Alloy and temper designations are in accordance with ANSI H35.1. The equivalent unified numbering system alloy designations are in accordance with Practice E 527.1.4 For acceptance criteria for inclusion of new aluminum and aluminum alloys and their properties in this specification, see Annex A1 and Annex A2.1.5 The values stated in inch-pound units are to be regarded as the standard. The SI values given in parentheses are for information only.

Standard Specification for Aluminum-Alloy Permanent Mold Castings

ASTM B26/B26M-03 铝合金砂型铸件标准规范

1.1 This specification covers aluminum-alloy sand castings designated as shown in Table 1.1.2 This specification is not intended for aluminum-alloy sand castings used in aerospace applications.1.3 Alloy and temper designations are in accordance with ANSI H35.1 and H35.1M. Unified Numbering System alloy designations are in accordance with Practice E 527.1.4 Unless the order specifies the "M" specification designation, the material shall be furnished to the inch-pound units.1.5 For acceptance criteria for inclusion of new aluminum and aluminum alloys and their properties in this specification, see Annex A1 and Annex A2.1.6 The values stated in either inch-pound units or SI units are to be regarded separately as standards. The SI units are shown in brackets or in separate tables or columns. The values stated in each system are not exact equivalents; therefore, each system must be used independent of the other. Combining values from the two systems may result in nonconformance with the specification. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Aluminum-Alloy Sand Castings

ASTM B150/B150M-03 铝青铜杆材, 棒材和型材的标准规格

1.1 This specification establishes the requirements for aluminum bronze rod, bar, and shapes for Copper Alloys UNS Nos. C61300, C61400, C61900, C62300, C62400, C63000, C63020, C63200, C64200, and C64210.Note 18212;Product intended for hot forging is described in Specification B 124/B 124M.Note28212;Warning8212;Mercury is a definite health hazard in use and in disposal.1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

Standard Specification for Aluminum Bronze Rod, Bar, and Shapes

ASTM B211-03 铝及铝合金棒材、条材和线材标准规范

1.1 This specification covers rolled or cold-finished bar, rod, and wire in alloys (Note 1) and tempers as shown in Table 2. Note 18212;Throughout this specification use of the term alloyin the general sense includes aluminum as well as aluminum alloy.Note 28212;The term cold finished is used to indicate the type of surface finish, sharpness of angles, and dimensional tolerances produced by drawing through a die.Note 3See Specification B 221 for aluminum and aluminum-alloy extruded bars, rods, wire, shapes, and tubes; and Specification B 316 for aluminum and aluminum-alloy rivet and cold-heading wire and rods.1.2 Alloy and temper designations are in accordance with ANSI H35.1. The equivalent UNS alloy designations are those of preceded by A9, for example, A91100 for aluminum 1100 in accordance with Practice E 527.1.3 A complete metric companion to Specification B 211 has been developed8212;B 211M; therefore, no metric equivalents are presented in this specification.1.4 For acceptance criteria for inclusion of new aluminum and aluminum alloys in this specification, see Annex A2.

Standard Specification for Aluminum and Aluminum-Alloy Bar, Rod, and Wire

ASTM B211M-03 铝及铝合金棒材、条材和线材(米制)标准规范

1.1 This specification covers rolled or cold-finished bar, rod, and wire in alloys (Note 1) and tempers as shown in . Note 8212;Throughout this specification use of the term alloy in the general sense includes aluminum as well as aluminum alloy.Note 28212;The term cold finished is used to indicate the type of surface finish, sharpness of angles, and dimensional tolerances produced by drawing through a die.Note 38212;See Specification B 221M for aluminum and aluminum-alloy extruded bars, rods, wire, shapes, and tubes; and Specification B 316M for aluminum and aluminum-alloy rivet and cold-heading wire and rods.1.2 Alloy and temper designations are in accordance with ANSI H35.1M. The equivalent Unified Numbering System alloy designations are those of preceded by A9, for example, A91100 for aluminum 1100 in accordance with Practice E 527.1.3 This specification is the metric counterpart of Specification B 211.1.4 For acceptance criteria for inclusion of new aluminum and aluminum alloys in this specification, see Annex A2.

Standard Specification for Aluminum and Aluminum-Alloy Bar, Rod, and Wire [Metric]