77.150.30 铜产品 标准查询与下载

T/CSTM 00651-2021 钢/铁双金属复合耐磨铸件

本文件规定了钢/铁双金属复合耐磨铸件的术语和定义、分类、代号和标记、技术要求、试验方法、检验规则、标志、包装、贮存和运输等。 本文件适用于矿山、冶金、水泥、电力、化工、机械和建材等行业的钢/铁双金属耐磨铸件。其他类型的双金属耐磨铸件也可参照执行。

Steel/iron bimetal composite abrasion-resistant castings

T/SHSE 0001-2021 粗铜

标准中粗铜牌号为Cu90.00。化学成分符合下表规定：      牌号   　    Cu 不小于　      杂质含量  不大于 　　                         As　  Sb　    Bi　      Pb Cu90?.00C　90.00　0.50　 0.40   0.10    0.6 Cu80?.00C　80.00　0.50　 0.40   0.10    0.6 Cu70?.00C　70.00　0.50  0.40   0.10    0.6 Cu60?.00C　60.00　0.50　 0.40   0.10    0.6 化学成分的仲裁分析方法按YS/T 521（所有部分）的规定进行，物理规格采用相应的测量工具进行检测；表面质量用目视检查。检查规则：粗铜应由供方技术监督部门进行检验,保证产品质量符合本标准的规定，并填写质量证明书。粗铜应成批提交检验，每批由同一炉次的产品组成。化学成分按批检验，物理规格、表面质量逐块检验 。化学成分检验结果的数值修约接GB/T 8170的规定进行。  粗铜锭上应有生产厂的产品标志，每块粗铜锭上应用鲜明颜色标明批号、重量和牌号。每批粗铜应附有质量证明书，注明：供方名称、地址、电话、传真；产品名称和牌号、规格；批号；净重和件数；分析检验结果和质量监督部门印记；本标准编号； 出厂日期和需方名称。

Blister Copper

PN-EN 13605-2021-10 E 铜和铜合金—电工用铜型材和异型线

Copper and copper alloys -- Copper profiles and profiled wire for electrical purposes

PN-EN 13601-2021-10 E 铜及铜合金 通用电工用铜棒、棒、线

Copper and copper alloys -- Copper rod, bar and wire for general electrical purposes

ASTM B61-15(2021) 蒸汽或阀门青铜铸件的标准规范

1.1 This specification2 establishes requirements for a highgrade steam-metal or valve-bronze alloy (Copper Alloy UNS No. C922003 ) used for component castings of valves, flanges, and fittings. 1.2 The castings covered are used in products that may be manufactured in advance and supplied from stock by the manufacturer or other dealer. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Steam or Valve Bronze Castings

ASTM B740-21 铜镍锡调幅合金带材的标准规范

1.1 This specification establishes requirements for coppernickel-tin alloy strip for Copper Alloy UNS Nos. C72700, C72900, and C72650 in the following alloys: Copper Alloy UNS No. Nominal Composition Weight % Copper Nickel Tin C72700 85 9 6 C72900 77 15 8 C72650 87.5 7.5 5 1.2 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 The following safety hazard caveat pertains only to the test method(s) described in this specification. 1.3.1 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Copper-Nickel-Tin Spinodal Alloy Strip

ASTM B770-21 一般用途铜铍合金砂铸件标准规范

1.1 This specification establishes requirements for sand castings produced from copper-beryllium alloys. The following alloys are covered: Copper Alloy UNS No. Designation Copper Nickel Beryllium C81400 70C 99.1 ... 0.06 C82000 10C 97 ... 0.5 C82200 3C, 14C 98 2.0 0.5 C82400A 165C, 165CTA 97.8 ... 1.7 C82500A 20C, 20CTA 97.2 ... 2.0 C82510 21C 96.6 ... 2.0 C82600A 245C, 245CTA 96.8 ... 2.4 C82800A 275C, 275CTA 96.6 ... 2.6 C96700 72C 67.2 31.0 1.2 A When fine-grained castings are specified, 0.02 to 0.12 titanium is added for grain refinement, usually in the remelt ingot. See Specification B30. 1.2 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 The following safety hazard caveat pertains only to the test methods described in this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory requirements prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Copper-Beryllium Alloy Sand Castings for General Applications

ASTM B66-15(2021) 蒸汽机车易损件用青铜铸件标准规范

1.1 This specification establishes requirements for bronze castings for steam locomotive wearing parts. The following Copper Alloy UNS Nos. are specified: C93200, C93400, C93600, C93700, C93800, C94300, C94400, C94500, and C95400.2 NOTE 1—Historically, the alloys in this specification have been used in the applications listed in the Appendix. Actual practice may vary according to locomotive type and service. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Bronze Castings for Steam Locomotive Wearing Parts

PN-EN 13600-2021-09 E 铜及铜合金 电工用无缝铜管

Copper and copper alloys -- Seamless copper tubes for electrical purposes

OENORM EN 1978-2021 铜和铜合金 铜阴极

Copper and copper alloys - Copper cathodes

OENORM EN 13601-2021 铜和铜合金 一般电气用铜棒、棒和线材

Copper and copper alloys - Copper rod, bar and wire for general electrical purposes

OENORM EN 13605-2021 铜和铜合金 电工用铜型材和异型线

Copper and copper alloys - Copper profiles and profiled wire for electrical purposes

prEN 1978-2021 铜和铜合金 铜阴极

Copper and copper alloys - Copper cathodes

LST EN 13601-2021 铜和铜合金 一般电气用铜棒、棒和线材

Copper and copper alloys - Copper rod, bar and wire for general electrical purposes

LST EN 13603-2021 铜和铜合金 评估电工用拉制圆铜线上保护性锡涂层的试验方法

Copper and copper alloys - Test methods for assessing protective tin coatings on drawn round copper wire for electrical purposes

LST EN 13605-2021 铜和铜合金 电工用铜型材和异型线

Copper and copper alloys - Copper profiles and profiled wire for electrical purposes

DIN EN 13601:2021 铜和铜合金 一般电工用铜棒、条和线；德文版 EN 13601:2021

This document specifies the composition, property requirements including electrical properties, and tolerances on dimensions and form for copper rod, bar and wire for general electrical purposes. Cross sections and size ranges are:- round, square and hexagonal rod with diameters

Copper and copper alloys - Copper rod, bar and wire for general electrical purposes; German version EN 13601:2021

UNI EN 13601-2021 铜和铜合金 一般电气用铜棒、棒和线材

Copper and copper alloys - Copper rod, bar and wire for general electrical purposes

UNI EN 13605-2021 铜和铜合金 电工用铜型材和异型线

Copper and copper alloys - Copper profiles and profiled wire for electrical purposes

LST EN 13600-2021 铜和铜合金 电工用无缝铜管

Copper and copper alloys - Seamless copper tubes for electrical purposes