共找到 1326 条与 铜产品 相关的标准,共 89 页
Copper and copper alloys - Seamless copper tubes for electrical purposes
Copper and copper alloys – Copper rod, bar and wire for general electrical purposes
Copper and copper alloys – Copper profiles and profiled wire for electrical purposes
Copper and copper alloys - Copper profiles and profiled wire for electrical purposes
Copper and copper alloys - Copper rod, bar and wire for general electrical purposes
Copper and copper alloys – Seamless copper tubes for electrical purposes
Copper and copper alloys - Seamless copper tubes for electrical purposes
Copper and copper alloys - Seamless copper tubes for electrical purposes
本文件规定了空调四通阀用无缝黄铜管的术语和定义、产品与标记、技术要求、试验方法、检验规则、标志、包装、运输、贮存及随行文件、订货单内容。 本文件适用于空调四通阀用拉制无缝黄铜管材。
Seamless brass tube for air conditioning four-way valve
本标准规定了空调四通阀用无缝黄铜管的术语和定义、产品与标记、技术要求、试验方法、检验规则、标志、包装、运输、贮存及随行文件、订货单内容。
Seamless brass tube for air conditioning four-way valve
1.1?This test method establishes the requirements for the determination of the reversed or repeated bending fatigue properties of copper alloy flat sheet or strip of spring materials by fixed cantilever, constant deflection (that is, constant amplitude of displacement)-type test
Standard Test Method for Bending Fatigue Testing for Copper-Alloy Spring Materials
Standard Guide for Editorial Procedures and Form of Product Specifications for Copper and Copper Alloys
Copper and copper alloys. Copper rod, bar and wire for general electrical purposes
Silicon-manganese bronze strips and ribbons. Specifications
1.1 This specification establishes the requirements for electrolytic copper cathode; electrorefined and electrowon. 1.2 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. NOTE 1—Cathode produced to this specification corresponds to the designation “Cath” as defined in Classification B224 and may be used to produce all other coppers listed in Classification B224 that are normally produced from “Cath” copper. NOTE 2—Grade 1 cathode conforms to the chemical compositional requirements of Copper UNS No. C11040, except for oxygen, and is suitable for the manufacture of wire rod as designated in Specification B49. 1.3 The following hazard caveat applies to the test methods described in Annex A2 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Standard Specification for Electrolytic Copper Cathode
1.1?This specification establishes requirements for round, hexagonal, octagonal, rectangular and square brass wire of UNS Alloy Nos. C21000, C22000, C22600, C23000, C23400, C24000, C26000, C27000, and C27400. 1.2?Units—The values stated in either SI units or inch-pound units ar
Standard Specification for Brass Wire
Silver oxygen-free copper special-shaped wire blank for motor commutator
Copper and copper alloy cast rods
Atomized phosphor bronze powder
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号