77.150.30 铜产品 标准查询与下载

ASTM B197/B197M-20 铜铍合金线标准规范

Standard Specification for Copper-Beryllium Alloy Wire

ASTM B30-20 铸锭和其他重熔形式的铜合金的标准规范

Standard Specification for Copper Alloys in Ingot and Other Remelt Forms

ASTM B301/B301M-13(2020) 自由切割铜杆 棒 线和形状的标准规格

1.1 This specification establishes the requirements for freecutting copper rod, bar, wire, and shapes of UNS Alloy Nos. C14500, C14510, C14520, C14700, and C18700, suitable for high-speed screw machine work or for general applications. 1.2 Typically, product made to this specification is furnished as straight lengths. Sizes 1⁄2 in. [12 mm] and under may be furnished in coils when requested. 1.3 Units—The values stated in either SI units or inchpound units are to be regarded separately as standard. Within the text, SI units are shown in brackets. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Free-Cutting Copper Rod, Bar, Wire, and Shapes

T/CNIA 0039-2020 真空自耗电弧炉用铜坩埚

本标准规定了真空自耗电弧炉用铜坩埚的技术要求、试验方法、检验规则、标志、包装、运输、贮存、质量证明书与订货单（或合同）内容。 本标准适用于拼焊结构或整体锻造、挤压等方法生产的真空自耗电弧炉用铜坩埚。

Copper crucible for vacuum consumable electric arc furnace

T/CNIA 0041-2020 真空凝壳炉用铜坩埚

本标准规定了真空凝壳炉用铜坩埚的技术要求、试验方法、检验规则、标志、包装、运输、贮存、质量证明书和订货单（或合同）内容。 本标准适用于整体生产的真空凝壳炉用铜坩埚（以下简称坩埚）。

Copper crucible for vacuum shell furnace

T/CIAA 006-2020 防霉抗菌铜锌复合粉

本标准规定了防霉抗菌铜锌复合粉的术语和定义、技术要求、试验方法、检验规则、标志、包装、运输与储存。

Anti-mildew and antibacterial Cu/Zn composite powder

ASTM F96-77(2020) 铜和镍在锻造形式的电子级合金的标准规范

1.1 This specification covers alloys of copper and nickel in a variety of wrought shapes suitable for external and internal use in electron devices. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 The following safety hazards caveat applies to Test Methods Section 8 only: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Electronic Grade Alloys of Copper and Nickel in Wrought Forms

ASTM B747-20 铜锆合金薄板和带材的标准规范

1.1 This specification establishes the requirements for Copper Alloy UNS C15100 sheet and strip. 1.2 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.2.1 Exception—Values given in inch-pound units are the standard except for grain size, which is stated in SI units. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Copper-Zirconium Alloy Sheet and Strip

ASTM B75/B75M-20 无缝铜管标准规范

1.1 This specification2 establishes the requirements for seamless round, rectangular, and square copper tube suitable for general engineering applications. 1.1.1 Tubes made from any of the following Copper UNS No. designations shall be supplied unless otherwise specified in the contract or purchase order: Copper UNS No. Type of Copper C10100 Oxygen-free electronic C10200 Oxygen-free without residual deoxidants C10300 Oxygen-free, extra low phosphorus C10800 Oxygen-free, low phosphorus C12000 Phosphorus deoxidized, low residual phosphorus C12200 Phosphorus deoxidized, high residual phosphorus 1.2 Units—The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, SI units are shown in brackets. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.3 The following safety hazard caveat pertains only to the test methods described in this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Seamless Copper Tube

ASTM B43-20 标准尺寸红色无缝黄铜管的标准规范

1.1 This specification2 establishes requirements for seamless red brass (Copper Alloy UNS No. C23000)3 pipe in nominal pipe sizes, both regular and extra-strong. In the annealed temper (O61), the pipe is suitable for use in plumbing, boiler feed lines, and for similar purposes. In the drawn general purpose temper (H58), the pipe is suitable for architectural applications, such as guard railings and stair hand railings. 1.2 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 The following hazard caveat pertains only to the test method portion, 9.1.1, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 Warning—Mercury has been designated by many regulatory agencies as a hazardous substance that can cause serious medical issues. Mercury, or its vapor, has been demonstrated to be hazardous to health and corrosive to materials. Use caution when handling mercury and mercury-containing products. See the applicable product Safety Data Sheet (SDS) for additional information. The potential exists that selling mercury or mercury-containing products, or both, is prohibited by local or national law. Users must determine legality of sales in their location. (See 9.2.) 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Seamless Red Brass Pipe, Standard Sizes

ASTM B464/B464M-15(2020) 焊接UNS N08020合金管的标准规范

1.1 This specification2 covers welded UNS N08020 alloy pipe for general corrosion-resisting and lowor hightemperature service. 1.2 The pipe covered is nominal pipe sizes up to and including NPS 6 [168 mm] with the nominal wall thicknesses given as Schedules 5S, 10S, and 40S and nominal pipe sizes up to and including NPS 2 [60 mm] also including Schedule 80S. Table 2 of Specification B775 is based on Table A1 of ANSI B36.19 and gives the nominal dimensions of these sizes. Table 3 of Specification B775 lists the dimensional requirements of these sizes. Pipe having other dimensions may be furnished provided such pipe complies with all other requirements of this specification. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Welded UNS N08020 Alloy Pipe

ASTM B592-20 铜 - 锌 - 钴 - 钴合金 铜 - 锌 - 锡 - 铁合金板 板 带和轧制棒的标准规范

1.1 This specification establishes the requirements for Copper Alloy UNS C66300 and C68800 plate, sheet, strip, and rolled bar.2 NOTE 1—Since alloy C68800 is frequently used in a variety of applications where yield strength and stress-corrosion resistance may be critical, it is recommended that drawings or samples of the part to be fabricated and details of application be submitted for use in establishing temper and treatment of material. 1.2 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units, which are provided for information only and are not considered standard. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Copper-Zinc-Aluminum-Cobalt Alloy, Copper-Zinc-Tin-Iron Alloy Plate, Sheet, Strip, and Rolled Bar

ASTM B249/B249M-20 锻铜和铜合金棒、棒材、型材和锻件的一般要求

Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Rod, Bar, Shapes and Forgings

ASTM B591-20 铜锌锡和铜锌锡铁镍合金板、薄板、带材和轧制棒材的标准规范

Standard Specification for Copper-Zinc-Tin and Copper-Zinc-Tin-Iron-Nickel Alloys Plate, Sheet, Strip, and Rolled Bar

ASTM B534-20 铜 - 钴 - 铍合金和铜 - 铍 - 铍合金板 板 带和轧制棒的标准规范

1.1 This specification establishes the requirements for plate, sheet, strip, and rolled bar. The following alloys are included:2 Previously Nominal Composition, % Copper Alloy Used UNS No. Designation Beryllium Cobalt Nickel Iron C17500 Alloy 10 0.6 2.5 ... ... C17510 Alloy 3 or 14 0.4 ... 1.8 ... C71700 ... 0.5 ... 31.0 0.70 1.2 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 The following safety hazard caveat pertains only to the test methods described in this specification: 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Copper-Cobalt-Beryllium Alloy and Copper-Nickel-Beryllium Alloy Plate, Sheet, Strip, and Rolled Bar

ASTM B455/B455M-20 铜 - 铅铅合金（铅 - 黄铜）挤压形状的标准规范

1.1 This specification establishes the requirements for extruded leaded-brass angles, channels, and other architectural shapes of solid cross section produced in Copper Alloy UNS Nos. C38000 and C38500. 1.1.1 Pipe, tube, or other hollow section products are not included in this specification. 1.2 Units—The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, SI units are shown in brackets. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Copper-Zinc-Lead Alloy (Leaded-Brass) Extruded Shapes

ASTM B379-20 磷化铜标准规范&x2014；炼油厂形状

1.1 This specification establishes the requirements for phosphorized copper wire bars, billets, and cakes. NOTE 1—Wire bars furnished under this specification do not conform in dimensions with that furnished under Specification B5. 1.2 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 The following safety hazard caveat pertains only to the test method in 14.2 and 14.3 in this specification. 1.3.1 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Phosphorized Coppers—Refinery Shapes

ASTM B283/B283M-20 铜和铜合金模锻件（热压）的标准规范

Standard Specification for Copper and Copper-Alloy Die Forgings (Hot-Pressed)

ASTM B593-20 铜合金弹簧材料弯曲疲劳试验的标准试验方法

Standard Test Method for Bending Fatigue Testing for Copper-Alloy Spring Materials

ASTM B124/B124M-20 铜和铜合金锻造棒、棒和型材的标准规范

1.1 This specification establishes the requirements for copper and copper alloy rod, bar, and shapes intended for hot forging. The following coppers and copper alloys are involved: Copper UNS Nos. Copper Alloy UNS Nos. Copper Alloy EN 1412 Nos. C11000 C27450 C49350 CW612N C14500 C27451 C49355 CW617N C14700 C27453 C49360 C28500 C61900 C35330 C62300 C36300 C63000 C36500 C63200 C37000 C64200 C37700 C64210 C46400 C65500 C46500 C65680 C46750 C67500 C48200 C67600 C48500 C69150 C48600 C69240 C48640 C69300 C48645 C69410 C49250 C69850 C49255 C70620 C49260 C71520 C49265 C77400 C49300 C87700 C49340 C87710 C49345 NOTE 1—Additional information about forging practice and forgings produced from these alloys is given in Appendix X1 and in Specification B283/B283M. 1.2 Units—The values stated in either SI units or inchpound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory requirements prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Copper and Copper Alloy Forging Rod, Bar, and Shapes