77.150.30 铜产品 标准查询与下载

ASTM B369/B369M-20 铜镍合金铸件的标准规范

1.1 This specification establishes the requirements for copper-nickel alloy castings with nominal compositions shown in Table 1. 1.2 Castings of these alloys are used primarily for corrosion-resistance applications such as construction or pressure vessels, particularly for marine pumps, valves, and fittings. 1.3 These alloys are considered weldable, but they may be ordered with a weld test to ensure weldability. When extensive welding is to be performed on the casting, weldability tests should be specified in the ordering information (5.2.6) to ensure proper welding characteristics. 1.4 Units—The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, SI units are shown in brackets. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.5 The following hazard statement applies only to Section 8, Weldability Test, of this specification.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Copper-Nickel Alloy Castings

ASTM B591-20 铜锌锡和铜锌锡铁镍合金板、薄板、带材和轧制棒材的标准规范

Standard Specification for Copper-Zinc-Tin and Copper-Zinc-Tin-Iron-Nickel Alloys Plate, Sheet, Strip, and Rolled Bar

ASTM B593-20 铜合金弹簧材料弯曲疲劳试验的标准试验方法

Standard Test Method for Bending Fatigue Testing for Copper-Alloy Spring Materials

ASTM B592-20 铜 - 锌 - 钴 - 钴合金 铜 - 锌 - 锡 - 铁合金板 板 带和轧制棒的标准规范

1.1 This specification establishes the requirements for Copper Alloy UNS C66300 and C68800 plate, sheet, strip, and rolled bar.2 NOTE 1—Since alloy C68800 is frequently used in a variety of applications where yield strength and stress-corrosion resistance may be critical, it is recommended that drawings or samples of the part to be fabricated and details of application be submitted for use in establishing temper and treatment of material. 1.2 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units, which are provided for information only and are not considered standard. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Copper-Zinc-Aluminum-Cobalt Alloy, Copper-Zinc-Tin-Iron Alloy Plate, Sheet, Strip, and Rolled Bar

ASTM B249/B249M-20 锻铜和铜合金棒、棒材、型材和锻件的一般要求

Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Rod, Bar, Shapes and Forgings

T/JXTX 0001-2020 江西绿色生态 电工用铜线坯

3 术语和定义      DB36/T 1138-2019界定的以及下列术语和定义适用于本文件。 3.1　     电工用铜线坯 copper drawing stock for electrical purpose 采用连铸连轧法及上引法生产的直径为6.0mm～35.0mm并供进一步拉制线材或其他电工用铜导体的圆形截面铜线坯。 3.2      “江西绿色生态”电工用铜线坯 copper drawing stock for electrical purpose - Jiangxi green ecology 符合“江西绿色生态”品牌评价通用要求及本标准技术要求，并通过“江西绿色生态”品牌评价活动的电工用铜线坯产品。 3.3 　     新鲜水 fresh water 　电工用铜线坯补充进循环水系统的自来水或处理水。 4 评价要求  4.1 基本要求 4.1.1 企业生产的电工用铜坯的化学成分、尺寸及其允许偏差、表面质量、力学性能等产品质量要求应符合GB/T 3952的相关规定，扭转性能、电性能以及铜粉量等产品质量指标应满足表1和表2中要求。 4.1.2 企业的污染物总量控制，应达到国家和地方污染物排放总量的控制指标。 4.1.3 企业的管理，应按照GB/T 19001 、GB/T 28001、 GB/T 24001及GB/T 23331分别建立并运行质量管理体系、职业健康安全管理体系、环境管理体系及能源管理体系，企业安全管理应达到GB/T 33000的要求。 4.1.4 企业的电工用铜线坯单位产品综合能耗应满足GB 32046标准中准入值的要求。 4.1.5 企业不应使用国家或有关部门发布的淘汰或禁止的技术、工艺、装备及材料。  4.1.6 企业所产生危险废物应有符合GB 18597要求的专门储存场所或交有资质的第三方处置。 4.1.7 产品包装材料满足使用要求条件下，应采用可再生利用或可降解材料。 4.1.8 企业应按照GB/T 33635的要求，推行绿色供应链管理，带动供应链上下游企业持续提高资源能源利用效率，改善环境绩效，实现绿色发展。 4.2 评价指标要求  4.2.1 绿色生态电工用铜线坯产品评价指标由一级指标和二级指标组成。一级指标包括资源节约属性指标、环境保护属性指标、生态协同属性指标和质量引领属性指标。二级指标是一级指标的具体化。连铸连轧法及上引法的电工用铜线坯产品的评价指标、基准值、判定依据等要求分别见表1和表2。 4.2.2企业应持续对生态协同、质量引领属性的二级指标进行细化，且细化的指标应遵循技术指标先进、国内一流、优于国家标准的原则。 4.3 数据来源   4.3.1 统计  企业的原辅材料及能源使用量、产品产量、废水、废气和固体废物产生量及相关技术经济指标等，以月报表或年报表为准。 4.3.2 实测  企业的原辅材料及能源使用量、产品产量、废水、废气和固体废物产生量及相关技术经济指标等也可选取有代表性生产时间段进行同步实测，所选取的生产时间段一般不少于一个月。 4.3.3 采样和监测      污染物排放指标的采样和监测按照相关技术规范执行，并采用国家或行业标准监测分析方法。 4.4 评价方法    由“江西绿色生态”评价机构，依据“江西绿色生态”标准及相应评价实施细则，实施评价。 4.5 评价报告 “江西绿色生态”评价机构按照DB 36/T1138-2019的要求，对参评的产品出具评价报告，符合评价要求，授予认证证书和标志。 _________________________________

Copper drawing stock for electrical purpose - Jiangxi green ecology

ASTM B360-20 限流器用硬拉铜毛细管的标准规范

1.1 This specification establishes the requirements for harddrawn, seamless capillary tube made from Copper Alloy UNS Nos. C10800, C12000, or C12200. 1.2 This tube is commonly supplied in straight lengths intended for restrictor applications such as metering lines for liquids and gases where close control over smoothness and diameter of the bore is required to insure uniform flow characteristics between tubes. 1.3 Units—The values stated in inch pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Hard-Drawn Copper Capillary Tube for Restrictor Applications

KS D 6024-2019 铜及铜合金铸件

Copper and copper alloy castings

KS D 6025-2019 铜合金连铸

Copper alloy continuous castings

T/SPSTS 012-2019 锂离子电池用微孔铜箔集流体

1 范围 2 规范性引用文件 3 术语和定义 4 技术要求 5 检测方法 6 检验规则 7 检测报告 8 标志、包装、运输、贮存 9 使用说明及注意事项 附录A 质量检测报告

Current collector of micro-porous copper foil for lithium-ion battery

T/ZZB 1468-2019 复合触点材料用铜及铜合金带材

本标准规定了复合触点材料用铜及铜合金带材的基本要求、技术要求、试验方法、检验规则、标志、包装、运输、贮存、质量证明书和质量承诺。 本标准适用于复合触点材料用铜及铜合金带材（以下简称铜带）。 

Copper and copper alloy strip for compound contacts

T/ZZB 1331-2019 无缝内螺纹铜管

本标准规定了无缝内螺纹铜管的术语和定义、基本要求、技术要求、试验方法、检验规则和包装、标志、运输、贮存、质量证明书、订货单(或合同)内容及质量承诺等。 本标准适用于空调与制冷设备用无缝内螺纹铜管。

Seamless inner grooved copper tube

ASTM B702-93(2019) 铜钨电接触材料的标准规范

1.1 This specification covers electrical contact components made from copper tungsten by powder metallurgical procedures. 1.2 This specification covers compositions within the copper tungsten system normally specified by users of contacts. 1.3 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Data Safety Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Copper-Tungsten Electrical Contact Material

T/ZZB 1251-2019 卫生洁具用黄铜管

本标准规定了卫生洁具用黄铜管的术语和定义、产品分类与标记、基本要求、技术要求、试验方法、检验规则、标志、包装、运输、贮存和质量证明书、质量承诺。 本标准适用于卫生洁具用横截面为圆形、矩（方）形、扁圆形、椭圆形、 D形的拉制黄铜管材(以下简称管材)。

Brass tube for sanitary ware

ASTM B152/B152M-19 铜板、带材、板材和轧制棒材的标准规范

1.1 This specification2 establishes the requirements for copper sheet, strip, plate, and rolled bar produced from the following coppers. Copper UNS No.A Previous Designation Type of Copper C10100B OFE Oxygen-free electronic C10200B OF Oxygen-free without residual deoxidants C10300 OFXLP Oxygen-free extra low phosphorus C10400, C10500, C10700 OFS Oxygen-free, silver bearing C10800 OFLP Oxygen-free low phosphorus C10910 ... Low oxygen C11000B, C ETP, TPC Electrolytic tough pitch,C Tough pitchC C11300, C11400, C11600B STP Silver bearing tough pitch C12000 DLP Phosphorized, low residual phosphorus C12200B DHP Phosphorized, high residual phosphorus C12300 DHPS Phosphorized, silver bearing C14200 DPA Phosphorus deoxidized, arsenical C14420 ... Tin bearing tellurium copper C14530 ... Tin tellurium bearing copper A Except Copper UNS Nos. C10910 (low oxygen), C14200 (phosphorus deoxidized, arsenical), C14420 (tin bearing tellurium), and C14530 (tin tellurium bearing) these types of copper are classified in Classification B224. B SAE Specification CA101 conforms to Copper UNS No. C10100; SAE Specification CA102 conforms to the requirements for Copper UNS No. C10200; SAE Specification CA110 conforms to the requirements for Copper UNS No. C11000; SAE Specifications CA113, CA114, and CA116 conform to the requirements for Copper UNS Nos. C11300, C11400, and C11600; SAE Specification CA120 conforms to Copper UNS No. C12000; and SAE Specification CA122 conforms to the requirements for Copper UNS No. C12200. C Unless specified in the contract or purchase order the supplier is permitted to provide ETP copper or TP copper. NOTE 1—Each of the coppers listed has unique properties that can make it suitable for specific applications. The purchaser should consult with the supplier to determine which copper would be best suited for the intended application. NOTE 2—This specification is not intended to establish requirements for material rolled to ounce-weight thicknesses. Such material is defined in Specification B370. Flat copper products with finished (rolled or drawn) edges (flat wire and strip) are defined in Specification B272. 1.1.1 When a specific copper is not identified in the contract or purchase order, the supplier may furnish product from any of the listed coppers. 1.2 Units—The values stated in either inch-pound units or SI units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other and values from the two systems shall not be combined. 1.3 The following safety hazard caveat pertains only to the test method(s) described in this specification: 1.3.1 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Copper Sheet, Strip, Plate, and Rolled Bar

ASTM B101-12(2019) 建筑结构用镀铅铜板和带材的标准规范

Standard Specification for Lead-Coated Copper Sheet and Strip for Building Construction

ASTM B103/B103M-19 磷青铜板、薄板、带材和轧制棒材的标准规范

1.1 This specification establishes the requirements for copper-tin alloy (phosphor bronze), copper-tin-lead alloy (leaded phosphor bronze), and copper-tin-lead-zinc alloy (bearing bronze), plate, sheet, strip, and rolled bar. The phosphor bronzes commonly are used for deep drawing into bellows and stamping and forming into spring devices and into terminals and connectors for electrical apparatus because they combine high strength with high elongation. The leaded phosphor bronzes are used where strength, corrosion resistance, and machinability are required. The bearing bronze is used in bushings, bearings, and load-bearing thrust washers. The following alloys are covered: Copper Alloy UNS No.2 Nominal Composition, % Previously Used Designation Copper Tin Zinc Lead C51000 95 5 . . . . . . A1 C51100 96 4 . . . . . . A C51180 96 4 . . . . . . . . . C51900 94 6 . . . . . . C52100A 92 8 . . . . . . C C52180 92 8 . . . . . . . . . C52400 90 10 . . . . . . D C53400 94 5 . . . 1 B1 C54400 88 4 3 4 B2 A SAE Specification CA 521 conforms to the requirements of UNS No. C52100. NOTE 1—All of the above alloys contain small amounts of phosphorus, used as a deoxidant in melting, and to enhance the mechanical properties. 1.2 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, SI units are shown in brackets. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.3 The following safety hazard caveat pertains only to the test method(s) described in this specification. 1.3.1 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Phosphor Bronze Plate, Sheet, Strip, and Rolled Bar

ASTM B16/B16M-19 用于螺丝机的自由切割黄铜棒 棒和形状的标准规格

1.1 This specification establishes the requirements for freecutting brass rod, bar, wire, and shapes of any specified cross section produced from Copper Alloy UNS Nos. C36000 or C36010 suitable for high-speed screw machining applications and moderate thread rolling. 1.2 Units—Values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other and values from the two systems shall not be combined. 1.2.1 Within the text, SI units are shown in brackets. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Free-Cutting Brass Rod, Bar and Shapes for Use in Screw Machines

ASTM B124/B124M-19a 铜和铜合金锻造棒、棒和型材的标准规范

Standard Specification for Copper and Copper Alloy Forging Rod, Bar, and Shapes

ASTM B249/B249M-19a 锻铜和铜合金棒、棒材、型材和锻件的一般要求

Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Rod, Bar, Shapes and Forgings