77.150.30 铜产品 标准查询与下载

ASTM B103/B103M-19 磷青铜板、薄板、带材和轧制棒材的标准规范

1.1 This specification establishes the requirements for copper-tin alloy (phosphor bronze), copper-tin-lead alloy (leaded phosphor bronze), and copper-tin-lead-zinc alloy (bearing bronze), plate, sheet, strip, and rolled bar. The phosphor bronzes commonly are used for deep drawing into bellows and stamping and forming into spring devices and into terminals and connectors for electrical apparatus because they combine high strength with high elongation. The leaded phosphor bronzes are used where strength, corrosion resistance, and machinability are required. The bearing bronze is used in bushings, bearings, and load-bearing thrust washers. The following alloys are covered: Copper Alloy UNS No.2 Nominal Composition, % Previously Used Designation Copper Tin Zinc Lead C51000 95 5 . . . . . . A1 C51100 96 4 . . . . . . A C51180 96 4 . . . . . . . . . C51900 94 6 . . . . . . C52100A 92 8 . . . . . . C C52180 92 8 . . . . . . . . . C52400 90 10 . . . . . . D C53400 94 5 . . . 1 B1 C54400 88 4 3 4 B2 A SAE Specification CA 521 conforms to the requirements of UNS No. C52100. NOTE 1—All of the above alloys contain small amounts of phosphorus, used as a deoxidant in melting, and to enhance the mechanical properties. 1.2 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, SI units are shown in brackets. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.3 The following safety hazard caveat pertains only to the test method(s) described in this specification. 1.3.1 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Phosphor Bronze Plate, Sheet, Strip, and Rolled Bar

ASTM B101-12(2019) 建筑结构用镀铅铜板和带材的标准规范

Standard Specification for Lead-Coated Copper Sheet and Strip for Building Construction

ASTM B249/B249M-19a 锻铜和铜合金棒、棒材、型材和锻件的一般要求

Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Rod, Bar, Shapes and Forgings

T/ZZB 1173-2019 换向器用银无氧铜线坯

本标准规定换向器用银无氧铜线坯的基本要求、技术要求、试验方法、检验规则、标志、包装、运输与贮存、质量证明书、订货单（或合同）和质量承诺等内容。 本标准适用于直径为 8 mm～20 mm，供进一步加工的换向器用银无氧铜线坯（以下简称线坯）。

Silver oxygen-free copper drawing stock for commutator

YS/T 323-2019 铍青铜板材、带材和箔材

Beryllium Bronze Sheet, Strip and Foil

YS/T 1294-2019 接触线和绞线用铜及铜合金线坯

Copper and copper alloy wire blanks for contact wires and stranded wires

YS/T 648-2019 铜碲合金棒

Copper tellurium alloy rod

BS EN 17263:2019 铜及铜合金 对棒材、棒材、空心棒材和线材的外表面进行涡流检测 通过环绕测试线圈来检测缺陷

What is BS EN 17263- Eddy current testing about?    BS EN 17263 is a European standard on copper and copper alloys that discusses the criteria for eddy current testing. BS EN 17263 specifies a procedure for fully automatic eddy current testing with no operator involvement with an encircling test coil for detecting defects on the surface of copper and copper alloy rods, bars, hollow rods, and wires with a minimum diameter or width across flats defined in the relevant product standards.   NOTE 1: This test method can be continuous or discontinuous depending on the product.  NOTE 2: The product size range and test acceptance level are defined in the relevant product standards.   Who is BS EN 17263-

Copper and copper alloys. Eddy current testing on the outer surface of rods, bars, hollow rods and wires for the detection of defects by encircling test coil

T/ZZB 1104-2019 电机整流子用银无氧铜带材

本标准规定电机整流子用银无氧铜带材的基本要求、技术要求、试验方法、检验规则、标志、包装、运输、贮存、质量证明书、订货单（或合同）和质量承诺内容。 本标准适用于电机整流子用银无氧铜带材（以下简称“铜带”）。

Silver oxygen-free copper strip for engine commutator

T/ZZB 1088-2019 部分填充钢-混凝土组合柱

本标准规定了部分填充钢-混凝土组合柱的术语和定义、基本要求、技术要求、试验方法、检验规则、产品标志、合格证书和使用说明书、包装、运输、贮存和质量承诺。 本标准适用于以钢结构为主体的装配式建筑用部分填充钢-混凝土组合柱（以下简称PEC柱）。

Partially encased composite column

T/ZZB 1067-2019 铜门用及铜门装饰用铜带

本标准规定了牌号为T2、T3铜门用及铜门装饰用铜带的基本要求、技术要求、试验方法、检验规则、包装、标志、运输、贮存、订货单（合同）和质量承诺等内容。 本标准适用于铜门用铜带及铜瓦、铜雕塑、屋面、屋顶、外墙面、工艺品、日常用品等装饰用铜带（以下简称“铜带”）。

Copper doors and copper doors decoration copper strip

ASTM B98/B98M-13(2019) 铜硅合金棒材和型材标准规范

1.1 This specification establishes requirements for coppersilicon rod, bar, and shapes for UNS Copper Alloys C65100, C65500, and C66100. NOTE 1—Material for hot forging is covered by Specification B124/ B124M. NOTE 2—For ASME Boiler and Pressure Vessel Code applications, see Specification SB-98 in Section II of that code. 1.2 Units—The values stated in either SI units or inchpound units are to be regarded separately as standard. Within the text, SI units are shown in brackets. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other and values from the two systems shall not be combined. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Copper-Silicon Alloy Rod, Bar and Shapes

ASTM B272-12(2019) 带成品（轧制或拉制）边（扁线和带材）的铜扁制品的标准规范

1.1 This specification establishes the requirements for copper products, flat wire and strip, with rolled or drawn finished edges produced for general application. 1.1.1 The product is produced in UNS Copper Nos. C10100, C10200, C10300, C10500, C10700, C10800, C11000, C11040, C12200, and C14200 unless otherwise established by agreement between manufacturer and purchaser. 1.2 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units, which are provided for information only and are not considered standard. NOTE 1—When a copper other than that listed in 1.1.1 is designated by the purchaser, the resulting product shall conform to the physical, mechanical, performance, dimensional, and tolerance requirements per agreement between the manufacturer and purchaser. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Copper Flat Products with Finished (Rolled or Drawn) Edges (Flat Wire and Strip)

ASTM B130-19 防弹衣用商业青铜带的标准规范

1.1 This specification establishes the requirements for commercial bronze strip for manufacture of bullet jacket cups and ammunition components from Copper Alloy UNS No. C22000.2 1.2 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Commercial Bronze Strip for Bullet Jackets

ASTM B981/B981M-19 低铅黄铜棒、棒、线和型材的标准规范

1.1 This specification establishes the requirements for low leaded brass rod, bar, wire, and shapes of any specified cross section produced from Copper Alloys UNS No. C36300, C36500, C37000, C37100 and C37700 suitable for high-speed screw machining applications. NOTE 1—Refer to Specification B124/B124M when purchasing bar or rod for forging production. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Low-Leaded Brass Rod, Bar, Wire, and Shapes

ASTM B249/B249M-19 锻铜和铜合金棒、棒材、型材和锻件的一般要求

Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Rod, Bar, Shapes and Forgings

ASTM B68/B68M-19 光亮退火无缝铜管的标准规范

1.1 This specification establishes the requirements for bright annealed seamless copper tube suitable for use in refrigeration, oil lines, gasoline lines, and so forth, where tube with an interior surface essentially free from scale and dirt is required. 1.1.1 Tubes made from any of the following Copper UNS No. designations shall be supplied, unless otherwise specified in the contract or purchase order: Copper UNS No.2 Type of Copper C10200 Oxygen-free C10300 Oxygen-free, (OFXLP) C10800 Oxygen-free, (OFLP) C12000 Phosphorus deoxidized, low residual phosphorus C12200 Phosphorus deoxidized, high residual phosphorus 1.2 Units—The values stated in either SI units or inchpound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Seamless Copper Tube, Bright Annealed

ASTM B694-19 电缆屏蔽用铜、铜合金、铜包青铜（CCB）、铜包不锈钢（CCS）和铜包合金钢（CAS）薄板和带材的标准规范

1.1 This specification establishes the requirements for copper, copper alloy, copper-clad bronze (CCB), copper-clad stainless steel (CCS), and copper-clad alloy steel (CAS) materials, sheet, and strip, in various thicknesses, for use as electrostatic or electromagnetic shielding for insulated power, control, instrumentation, and communication cables. NOTE 1—See Specification B736, for related standards for aluminumbased shielding materials. 1.2 The products covered are the following: Copper or Copper Alloy UNS No. Type of Products C11000 copper C19400 copper-iron alloy C22000 copper-zinc alloy (commercial bronze) C23000 copper-zinc alloy (red brass) C66400 copper-zinc-iron-cobalt alloy C66410 copper-zinc-iron alloy C66430 copper-zinc-iron-tin alloy C71000 cupro-nickel 20 % ... copper-clad bronze (CCB) ... copper-clad stainless steel (CCS) ... copper-clad alloy steel (CAS) 1.3 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3.1 The only exception is grain size, which is reported in SI (mm) units. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Copper, Copper-Alloy, Copper-Clad Bronze (CCB), Copper-Clad Stainless Steel (CCS), and Copper-Clad Alloy Steel (CAS) Sheet and Strip for Electrical Cable Shielding

ASTM B569-19 换热器管用窄宽度黄铜带和轻型量规的标准规范

1.1 This specification establishes the requirements for brass strip in narrow widths and light gages produced from Copper Alloys Nos. C23000, C26000, and C26130.2 NOTE 1—This product is commonly used for the manufacture of thin-wall tubes for water passages in heat exchangers for internal combustion engines and other closed-system heat sources. 1.2 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units, which are provided for information only and are not considered standard. 1.2.1 Exception—Grain size and chemical analysis sampling are stated in SI units. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Brass Strip in Narrow Widths and Light Gage for Heat-Exchanger Tubing

ASTM B315-19 无缝铜合金管

1.1 This specification2 establishes the requirements for seamless, copper alloy pipe and tube in nominal pipe sizes, both regular and extra strong, and seamless tube in straight lengths for general engineering purposes. Pipe and tube are produced in the copper alloy UNS Numbers: C61300, C61400, C63020, C65100, and C65500. 1.2 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 The following safety caveat pertains only to the test method(s) described in this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Seamless Copper Alloy Pipe and Tube